SIST EN 10251:2024
(Main)Magnetic materials - Methods of determination of the geometrical characteristics of electrical steel sheet and strip
Magnetic materials - Methods of determination of the geometrical characteristics of electrical steel sheet and strip
This European Standard is intended to define the test methods used for the determination of the following geometrical characteristics of electrical steel sheet and strip:
— edge wave (wave factor);
— residual curvature;
— edge camber;
— deviation from the shearing line due to internal stresses;
— burr height of cut edges.
This European Standard applies to electrical steel sheet and strip intended for the construction of magnetic circuits and corresponding to Clauses B2, C21 and C22 of IEC 60404-1:2000.
Magnetische Werkstoffe - Verfahren zur Bestimmung der geometrischen Kenngrößen von Elektroblech und -band
Dieses Dokument soll die Verfahren festlegen, nach denen die folgenden geometrischen Kenngrößen von Elektroblech und –band zu bestimmen sind:
— Kantenwelligkeit;
— Bogigkeit;
— Kantenkrümmung;
— Abweichung von der Schnittlinie aufgrund innerer Spannungen;
— Grathöhe von Schnittkanten.
Dieses Dokument gilt für Elektroblech und –band, das zum Aufbau magnetischer Kreise und entsprechend den Abschnitten B2, C21 und C22 der EN 60404-1:2017 verwendet werden soll.
Matériaux magnétiques - Méthodes de détermination des caractéristiques géométrique des bandes et tôles en acier électrique
Le présent document a pour objet de définir les méthodes d’essai à utiliser pour la détermination des
caractéristiques géométriques suivantes des bandes et tôles en acier électrique :
— ondulation de rive ;
— courbure résiduelle ;
— rectitude ;
— déviation par rapport à la ligne de cisaillage due aux tensions internes ;
— hauteur de bavure des rives cisaillées.
Le présent document s’applique aux bandes et tôles en acier électrique destinées à la construction de
circuits magnétiques et correspondant aux Articles B2, C21 et C22 de l’EN 60404-1:2017.
Magnetni materiali - Metode za ugotavljanje geometrijskih lastnosti elektropločevin in trakov
Ta evropski standard je namenjen opredelitvi preskusnih metod za ugotavljanje naslednjih geometrijskih lastnosti elektropločevin in trakov:
– robni val (valovni faktor);
– preostala ukrivljenost;
– previsni kot;
– odstopanje od strižne črte zaradi notranjih obremenitev;
– višina zarobka odrezanih robov.
Ta evropski standard se uporablja za elektropločevine in trakove, namenjene konstruiranju magnetnih krogov, ki ustrezajo točkam B2, C21 in C22 iz standarda IEC 60404-1:2000.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 10251:2024
01-maj-2024
Magnetni materiali - Metode za ugotavljanje geometrijskih lastnosti
elektropločevin in trakov
Magnetic materials - Methods of determination of the geometrical characteristics of
electrical steel sheet and strip
Magnetische Werkstoffe - Verfahren zur Bestimmung der geometrischen Kenngrößen
von Elektroblech und -band
Matériaux magnétiques - Méthodes de détermination des caractéristiques géométrique
des bandes et tôles en acier électrique
Ta slovenski standard je istoveten z: EN 10251:2024
ICS:
29.030 Magnetni materiali Magnetic materials
77.140.50 Ploščati jekleni izdelki in Flat steel products and semi-
polizdelki products
SIST EN 10251:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 10251:2024
---------------------- Page: 2 ----------------------
SIST EN 10251:2024
EN 10251
EUROPEAN STANDARD
NORME EUROPÉENNE
March 2024
EUROPÄISCHE NORM
ICS 29.030; 77.140.50 Supersedes EN 10251:2015
English Version
Magnetic materials - Methods of determination of the
geometrical characteristics of electrical steel sheet and
strip
Matériaux magnétiques - Méthodes de détermination Magnetische Werkstoffe - Verfahren zur Bestimmung
des caractéristiques géométrique des bandes et tôles der geometrischen Kenngrößen von Elektroblech und -
en acier électrique band
This European Standard was approved by CEN on 8 January 2024.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 10251:2024 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 10251:2024
EN 10251:2024 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Test Methods . 5
4.1 Edge wave . 5
4.2 Residual curvature . 6
4.3 Edge camber. 8
4.4 Deviation from the shearing line due to internal stresses . 9
4.5 Burr height . 10
5 Test report . 12
Annex A (informative) Examples of clamping systems . 13
Bibliography .
...
SLOVENSKI STANDARD
oSIST prEN 10251:2023
01-marec-2023
Magnetni materiali - Metode za ugotavljanje geometrijskih lastnosti
elektropločevin in trakov
Magnetic materials - Methods of determination of the geometrical characteristics of
electrical steel sheet and strip
Magnetische Werkstoffe - Verfahren zur Bestimmung der geometrischen Kenngrößen
von Elektroblech und -band
Matériaux magnétiques - Méthodes de détermination des caractéristiques géométrique
des bandes et tôles en acier électrique
Ta slovenski standard je istoveten z: prEN 10251
ICS:
29.030 Magnetni materiali Magnetic materials
77.140.50 Ploščati jekleni izdelki in Flat steel products and semi-
polizdelki products
oSIST prEN 10251:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 10251:2023
---------------------- Page: 2 ----------------------
oSIST prEN 10251:2023
DRAFT
EUROPEAN STANDARD
prEN 10251
NORME EUROPÉENNE
EUROPÄISCHE NORM
January 2023
ICS 29.030; 77.140.50 Will supersede EN 10251:2015
English Version
Magnetic materials - Methods of determination of the
geometrical characteristics of electrical steel sheet and
strip
Matériaux magnétiques - Méthodes de détermination Magnetische Werkstoffe - Verfahren zur Bestimmung
des caractéristiques géométrique des bandes et tôles der geometrischen Kenngrößen von Elektroblech und -
en acier électrique band
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 459/SC 8.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2023 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 10251:2023 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 10251:2023
prEN 10251:2023 (E)
Contents Page
European foreword . 3
1 Scope . 4
2 Normative references . 4
3 Terms and definitions . 4
4 Test Methods . 5
4.1 Edge wave . 5
4.1.1 Test specimen . 5
4.1.2 Measuring procedure. 5
4.2 Residual curvature . 6
4.2.1 General . 6
4.2.2 Horizontal method .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.