SIST EN 300 175-8 V2.9.1:2022
(Main)Digital Enhanced Cordless Telecommunications (DECT) - Common Interface (CI) - Part 8: Speech and audio coding and transmission
Digital Enhanced Cordless Telecommunications (DECT) - Common Interface (CI) - Part 8: Speech and audio coding and transmission
The present document is one of the parts of the specification of the Digital Enhanced Cordless Telecommunications
(DECT) Common Interface (CI).
This part of the DECT CI specifies the speech and audio coding and transmission requirements.
In order to ensure satisfactory interworking of different portable and fixed units, it is necessary to specify the
transmission performance of the analog information over the digital link. This requires not only use of a common
speech algorithm, but also standardization of frequency responses, reference speech levels (or loudness) at the air
interface and various other parameters.
The present document applies to DECT equipment which includes all the necessary functions to provide real-time
two-way speech conversation and stereo audio transmission. Several speech services are defined in the present
document, including conventional 3,1 kHz telephony, wideband 7 kHz voice transmission, super-wideband 14 kHz and
fullband 20 kHz service. DECT Fixed part providing such services may be connected to the public circuit switched
(PSTN/ISDN) network, to private networks or to the Voice over Internet Protocol (VoIP) network.
Tethered fixed point local loop applications are not required to comply with the requirements of the present document.
For the DECT systems which connect to the Public Switched Telephone Network (PSTN) via an analog interface, the
additional requirements, which are implemented in the FP, have as much as possible been aligned with ETSI
TBR 038 [29].
A summary of the control and the use of the DECT echo control functions, to guide on need for options to
manufacturers and installers, is found in annex A.
Information concerning test methods can be found in ETSI EN 300 176-1 [9] and ETSI EN 300 176-2 [10] (previously
covered by ETSI TBR 010 [i.5]). The test methods take into account that DECT is a digital system.
The present document includes New Generation DECT, a further development of the DECT standard introducing
wideband speech, improved data services, new slot types and other technical enhancements.
In addition, the present document includes DECT Evolution, providing SWB and FB speech and audio capabilities and
a new speech coding algorithm for NB and WB allowing to increase the audio quality of the NB and WB speech service
and improve bandwidth efficiency.
The latest update for DECT Evolution includes the support of ultra-band, high resolution, low-latency speech and audio
coding, and additional PP types supported with LC3plus coding. An application profile using these new PP types can be
found in ETSI TS 103 706 [i.28].
Digitalne izboljšane brezvrvične telekomunikacije (DECT) - Skupni vmesnik (CI) - 8. del: Kodiranje in prenos govora in zvoka
Ta dokument je eden od delov specifikacije skupnega vmesnika (CI) za digitalne izboljšane brezvrvične telekomunikacije (DECT).
Ta del specifikacije skupnega vmesnika za digitalne izboljšane brezvrvične telekomunikacije določa zahteve za kodiranje in prenos govora ter zvoka.
Za ustrezno medsebojno delovanje različnih prenosnih in fiksnih enot je treba določiti zmogljivost prenosa analognih informacij prek digitalne povezave. Pri tem se poleg uporabe skupnega govornega algoritma zahtevajo tudi standardizacija frekvenčnih odzivov, ravni referenčnega govora (ali glasnost) pri radijskem vmesniku in drugi različni parametri.
Ta dokument se uporablja za opremo digitalnih izboljšanih brezvrvičnih telekomunikacij, ki vključuje vse potrebne funkcije za zagotavljanje dvosmernih govorjenih pogovorov v realnem času in prenos stereo zvoka. V tem dokumentu je določenih več govornih storitev, vključno s standardno telefonsko storitvijo na frekvenci 3,1 kHz, širokopasovnim prenosom glasu na frekvenci 7 kHz, super širokopasovno storitvijo na frekvenci 14 kHz in polnopasovno storitvijo na frekvenci 20 kHz. Fiksni del digitalnih izboljšanih brezvrvičnih telekomunikacij, ki zagotavlja takšne storitve, je lahko povezan z omrežjem PSTN/ISDN, zasebnimi omrežji ali omrežjem prek internetnega protokola (VoIP).
Ni nujno, da za uporabo lokalnih zank fiksnih točk v skupni rabi veljajo zahteve iz tega dokumenta.
Za sisteme digitalnih izboljšanih brezvrvičnih telekomunikacij, ki so v omrežje PSTN povezani prek analognega vmesnika, so bile dodatne zahteve, uvedene v FP, v največji možni meri usklajene s standardom ETSI TBR 038 [29].
Povzetek nadzora in uporabe funkcij nadzora odmeva digitalnih izboljšanih brezvrvičnih telekomunikacij ter smernice z opisom možnosti za proizvajalce in montažerje so na voljo v Dodatku A.
Informacije o preizkusnih metodah so na voljo v standardih ETSI EN 300 176-1 [9] in ETSI EN 300 176-2 [10] (prej so bile zajete v standardu ETSI TBR 010 [i.5]). Pri preskusnih metodah se upošteva, da je DECT digitalni sistem.
Ta dokument vključuje novo generacijo digitalnih izboljšanih brezvrvičnih telekomunikacij, nadaljnji razvoj standarda o digitalnih izboljšanih brezvrvičnih telekomunikacijah, ki uvaja širokopasovni govor, izpopolnjene podatkovne storitve, nove tipe rež in druge tehnične izpopolnitve.
Poleg tega ta dokument vključuje razvoj digitalne izboljšane brezvrvične telekomunikacije, ki zagotavlja govorne in avdio zmogljivosti za SWB in FB ter nov algoritem kodiranja govora za storitvi NB in WB, kar omogoča večjo kakovost zvoka govornih storitev NB in WB ter izboljšuje zmogljivost pasovne širine.
Najnovejša posodobitev razvoja digitalnih izboljšanih brezvrvičnih telekomunikacij vključuje podporo ultra širokopasovnega, visokoločljivostnega kodiranja govora in zvoka z nižjo zakasnitvijo ter dodatne vrste prenosnih delov (PP), podprte s kodiranjem LC3plus. Profil aplikacije, ki uporablja te nove prenosne dele, je na voljo v standardu ETSI TS 103 706 [i.28].
General Information
Buy Standard
Standards Content (Sample)
ETSI EN 300 175-8 V2.9.1 (2022-03)
EUROPEAN STANDARD
Digital Enhanced Cordless Telecommunications (DECT);
Common Interface (CI);
Part 8: Speech and audio coding and transmission
---------------------- Page: 1 ----------------------
2 ETSI EN 300 175-8 V2.9.1 (2022-03)
Reference
REN/DECT-00358
Keywords
7 kHz, audio, broadband, codec, DECT, handsfree,
IMT-2000, loudspeaking, mobility, narrowband,
quality, radio, speech, TDD, TDMA, telephony,
terminal
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
If you find a security vulnerability in the present document, please report it through our
Coordinated Vulnerability Disclosure Program:
https://www.etsi.org/standards/coordinated-vulnerability-disclosure
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.
Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2022.
All rights reserved.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI EN 300 175-8 V2.9.1 (2022-03)
Contents
Intellectual Property Rights . 16
Foreword . 16
Modal verbs terminology . 16
1 Scope . 17
2 References . 17
2.1 Normative references . 17
2.2 Informative references . 19
3 Definition of terms, symbols and abbreviations . 21
3.1 Terms . 21
3.2 Symbols . 23
3.3 Abbreviations . 23
4 Configurations . 25
4.1 Reference configuration . 25
4.1.1 Basic configuration . 25
4.1.2 Portable Part (PP) . 26
4.1.2.1 Functional organization . 26
4.1.2.2 Volume control . 27
4.1.3 Fixed Part (FP) . 27
4.1.3.1 Digital interface . 27
4.1.3.2 Analog interface . 28
4.1.3.3 FP adaptive volume control . 29
4.1.3.4 Voice over IP (VoIP) interface . 29
4.2 Test configurations . 30
5 Encoding . 30
5.0 General . 30
5.1 32 kbit/s full term (ADPCM) G.726 . 30
5.1.1 Algorithm . 30
5.1.2 Bit sequence . 30
5.1.3 Characteristics of G.726 ADPCM codec . 30
5.2 64 kbit/s PCM G.711 . 31
5.2.1 Algorithm . 31
5.2.2 Bit sequence . 31
5.2.3 Characteristics of G.711 PCM codec . 31
5.2.4 Automatic detection of FAX/modem tone and switch to G.711 . 31
5.3 Wideband speech codec G.722 at 64 kbit/s . 31
5.3.0 General . 31
5.3.1 Algorithm . 31
5.3.2 Bit sequence . 32
5.3.3 Characteristics of G.722 wideband codec . 32
5.3.4 Optional Packet Loss Concealment algorithm (PLC) . 32
5.4 Wideband speech codec G.729.1 up to 32 kbit/s . 33
5.4.1 Algorithm . 33
5.4.2 Bit sequence . 33
5.4.3 Characteristics of G.729.1 codec . 33
5.4.4 Packet Loss Concealment algorithm (PLC) . 33
5.4.5 Supported bit rate in DECT . 34
5.5 Super-wideband MPEG-4 speech and audio coding . 34
5.5.1 Algorithm . 34
5.5.2 64 kbit/s, MPEG-4 ER AAC-LD codec . 34
5.5.3 32 kbit/s, MPEG-4 ER AAC-LD codec . 35
5.6 Narrowband, wideband, super-wideband, fullband, FBHR and ultra-band LC3plus speech and audio
coding . 35
5.6.1 Algorithm . 35
5.6.2 NB mode at 32 kbit/s gross bit rate and 10 ms frame size . 36
ETSI
---------------------- Page: 3 ----------------------
4 ETSI EN 300 175-8 V2.9.1 (2022-03)
5.6.3 WB mode at 32 kbit/s gross bit rate and 10 ms frame size . 36
5.6.4 SWB mode at 64 kbit/s gross bit rate and 10 ms frame size . 37
5.6.5 FB mode at 64 kbit/s gross bit rate and 10 ms frame size . 37
5.6.6 FB mode at 96 kbit/s gross bit rate and 10 ms frame size . 37
5.6.7 FB mode at 128 kbit/s gross bit rate and 10 ms frame size . 38
5.6.8 FB mode at 128 kbit/s gross bit rate and 5 ms frame size . 38
5.6.9 FB mode at 160 kbit/s gross bit rate and 5 ms frame size . 38
5.6.10 FB mode at 192 kbit/s gross bit rate and 5 ms frame size . 39
5.6.11 FB mode at 128 kbit/s gross bit rate and 2,5 ms frame size . 39
5.6.12 FB mode at 256 kbit/s gross bit rate and 2,5 ms frame size . 39
5.6.13 FBLFE mode at 32 kbit/s gross bit rate and 10 ms frame size . 39
5.6.14 FBLFE mode at 64 kbit/s gross bit rate and 5 ms frame size . 40
5.6.15 FB stereo mode at 128 kbit/s gross bit rate and 10 ms frame size . 40
5.6.16 FB stereo mode at 256 kbit/s gross bit rate and 5 ms frame size . 40
5.6.17 FB stereo mode at 320 kbit/s gross bit rate and 2,5 ms frame size . 40
5.6.18 FB stereo mode at 512 kbit/s gross bit rate and 2,5 ms frame size . 41
5.6.19 FBHR mode at 128 kbit/s gross bit rate and 10 ms frame size . 41
5.6.20 FBHR mode at 160 kbit/s gross bit rate and 10 ms frame size . 41
5.6.21 FBHR mode at 192 kbit/s gross bit rate and 10 ms frame size . 41
5.6.22 UBHR mode at 160 kbit/s gross bit rate and 10 ms frame size. 42
5.6.23 UBHR mode at 192 kbit/s gross bit rate and 10 ms frame size. 42
5.6.24 UBHR mode at 256 kbit/s gross bit rate and 10 ms frame size. 42
5.6.25 UBHR mode at 320 kbit/s gross bit rate and 10 ms frame size. 42
6 Transmission aspects . 43
6.1 Relative level . 43
6.2 Acoustic reference level . 43
6.3 Volume control . 43
7 Audio specifications . 43
7.1 Overall description . 43
7.1.1 Introduction to DECT audio specifications . 43
7.1.2 Introduction to the audio types . 43
7.1.3 List of Audio types . 44
7.1.4 Audio types for Portable Parts . 45
7.1.5 Audio types for Fixed Parts . 46
7.1.6 Complete DECT system . 46
7.1.7 Structure of the specification of the audio types . 47
7.1.8 Audio Types and codecs . 55
7.1.9 Audio Types and physical interfaces . 55
7.2 Audio types applicable to Portable Parts . 55
7.2.0 General . 55
7.2.1 Performance levels of DECT Portable Parts (handsets). 55
7.2.2 Type 0: Reference PP (RePP) . 57
7.2.3 PP Type 1a: "Classic" GAP narrowband handset . 57
7.2.3.1 Introduction . 57
7.2.3.2 Compatible services and codecs . 57
7.2.3.3 Specification. 57
7.2.4 PP Type 1b: "Improved" GAP narrowband handset . 58
7.2.4.1 Introduction . 58
7.2.4.2 Compatible services and codecs . 58
7.2.4.3 Specification. 58
7.2.5 PP Type 1c: HATS-tested "standard" narrowband handset . 58
7.2.5.1 Introduction . 58
7.2.5.2 Compatible services and codecs . 58
7.2.5.3 Specification. 58
7.2.6 PP Type 1d: HATS-tested "improved" narrowband handset . 59
7.2.6.1 Introduction . 59
7.2.6.2 Compatible services and codecs . 59
7.2.6.3 Specification. 59
7.2.7 PP Type 3a: HATS tested narrowband "standard" loudspeaking handsfree . 59
7.2.7.1 Introduction . 59
ETSI
---------------------- Page: 4 ----------------------
5 ETSI EN 300 175-8 V2.9.1 (2022-03)
7.2.7.2 Compatible services and codecs . 60
7.2.7.3 Specification. 60
7.2.8 PP Type 3b: HATS tested narrowband "improved" loudspeaking handsfree . 60
7.2.8.1 Introduction . 60
7.2.8.2 Compatible services and codecs . 60
7.2.8.3 Specification. 60
7.2.9 PP Type 2a: P.311-tested wideband handset. 60
7.2.9.1 Introduction . 60
7.2.9.2 Compatible services and codecs . 60
7.2.9.3 Specification. 60
7.2.10 PP Type 2b: HATS-tested "standard" wideband handset or headset . 61
7.2.10.1 Introduction . 61
7.2.10.2 Compatible services and codecs . 61
7.2.10.3 Specification. 61
7.2.11 PP Type 2c: HATS tested "improved" wideband handset or headset . 61
7.2.11.1 Introduction . 61
7.2.11.2 Compatible services and codecs . 61
7.2.11.3 Specification. 61
7.2.12 PP Type 4a: HATS tested wideband "standard" loudspeaking handsfree . 62
7.2.12.1 Introduction . 62
7.2.12.2 Compatible services and codecs . 62
7.2.12.3 Specification. 62
7.2.13 PP Type 4b: HATS tested wideband "improved" loudspeaking and handsfree . 62
7.2.13.1 Introduction . 62
7.2.13.2 Compatible services and codecs . 62
7.2.13.3 Specification. 62
7.2.14 PP Type 5a: super-wideband 14 kHz handset or headset. 63
7.2.14.1 Introduction . 63
7.2.14.2 Compatible services and codecs . 63
7.2.14.3 Specification. 63
7.2.15 PP Type 5b: super-wideband 14 kHz loudspeaking handsfree . 63
7.2.15.1 Introduction . 63
7.2.15.2 Compatible services and codecs . 63
7.2.15.3 Specification. 63
7.2.16 PP Type 6: PPs with external 2 wire, 3,1 kHz telephony interface . 63
7.2.16.1 Introduction . 63
7.2.16.2 Compatible services and codecs . 63
7.2.16.3 Specification. 63
7.2.17 PP Type 7a: fullband 20 kHz handset or headset . 63
7.2.17.1 Introduction . 63
7.2.17.2 Compatible services and codecs . 64
7.2.17.3 Specification. 64
7.2.18 PP Type 7b: fullband 20 kHz loudspeaking handsfree . 64
7.2.18.1 Introduction . 64
7.2.18.2 Compatible services and codecs . 64
7.2.18.3 Specification. 64
7.2.19 PP Type 7c, d, e, f: fullband 20 kHz stereo audio device . 64
7.2.19.1 Introduction . 64
7.2.19.2 Compatible services and codecs . 64
7.2.19.3 Specification. 64
7.2.20 PP Type 7g: FBHR 24 kHz headset device . 65
7.2.20.1 Introduction . 65
7.2.20.2 Compatible services and codecs . 65
7.2.20.3 Specification. 65
7.2.21 PP Type 7h: FBHR 24 kHz loudspeaking device . 65
7.2.21.1 Introduction .
...
SLOVENSKI STANDARD
SIST EN 300 175-8 V2.9.1:2022
01-maj-2022
Digitalne izboljšane brezvrvične telekomunikacije (DECT) - Skupni vmesnik (CI) - 8.
del: Kodiranje in prenos govora in zvoka
Digital Enhanced Cordless Telecommunications (DECT) - Common Interface (CI) - Part
8: Speech and audio coding and transmission
Ta slovenski standard je istoveten z: ETSI EN 300 175-8 V2.9.1 (2022-03)
ICS:
33.070.30 Digitalne izboljšane Digital Enhanced Cordless
brezvrvične telekomunikacije Telecommunications (DECT)
(DECT)
35.040.40 Kodiranje avdio, video, Coding of audio, video,
multimedijskih in multimedia and hypermedia
hipermedijskih informacij information
SIST EN 300 175-8 V2.9.1:2022 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 300 175-8 V2.9.1:2022
---------------------- Page: 2 ----------------------
SIST EN 300 175-8 V2.9.1:2022
ETSI EN 300 175-8 V2.9.1 (2022-03)
EUROPEAN STANDARD
Digital Enhanced Cordless Telecommunications (DECT);
Common Interface (CI);
Part 8: Speech and audio coding and transmission
---------------------- Page: 3 ----------------------
SIST EN 300 175-8 V2.9.1:2022
2 ETSI EN 300 175-8 V2.9.1 (2022-03)
Reference
REN/DECT-00358
Keywords
7 kHz, audio, broadband, codec, DECT, handsfree,
IMT-2000, loudspeaking, mobility, narrowband,
quality, radio, speech, TDD, TDMA, telephony,
terminal
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
If you find a security vulnerability in the present document, please report it through our
Coordinated Vulnerability Disclosure Program:
https://www.etsi.org/standards/coordinated-vulnerability-disclosure
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.
Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2022.
All rights reserved.
ETSI
---------------------- Page: 4 ----------------------
SIST EN 300 175-8 V2.9.1:2022
3 ETSI EN 300 175-8 V2.9.1 (2022-03)
Contents
Intellectual Property Rights . 16
Foreword . 16
Modal verbs terminology . 16
1 Scope . 17
2 References . 17
2.1 Normative references . 17
2.2 Informative references . 19
3 Definition of terms, symbols and abbreviations . 21
3.1 Terms . 21
3.2 Symbols . 23
3.3 Abbreviations . 23
4 Configurations . 25
4.1 Reference configuration . 25
4.1.1 Basic configuration . 25
4.1.2 Portable Part (PP) . 26
4.1.2.1 Functional organization . 26
4.1.2.2 Volume control . 27
4.1.3 Fixed Part (FP) . 27
4.1.3.1 Digital interface . 27
4.1.3.2 Analog interface . 28
4.1.3.3 FP adaptive volume control . 29
4.1.3.4 Voice over IP (VoIP) interface . 29
4.2 Test configurations . 30
5 Encoding . 30
5.0 General . 30
5.1 32 kbit/s full term (ADPCM) G.726 . 30
5.1.1 Algorithm . 30
5.1.2 Bit sequence . 30
5.1.3 Characteristics of G.726 ADPCM codec . 30
5.2 64 kbit/s PCM G.711 . 31
5.2.1 Algorithm . 31
5.2.2 Bit sequence . 31
5.2.3 Characteristics of G.711 PCM codec . 31
5.2.4 Automatic detection of FAX/modem tone and switch to G.711 . 31
5.3 Wideband speech codec G.722 at 64 kbit/s . 31
5.3.0 General . 31
5.3.1 Algorithm . 31
5.3.2 Bit sequence . 32
5.3.3 Characteristics of G.722 wideband codec . 32
5.3.4 Optional Packet Loss Concealment algorithm (PLC) . 32
5.4 Wideband speech codec G.729.1 up to 32 kbit/s . 33
5.4.1 Algorithm . 33
5.4.2 Bit sequence . 33
5.4.3 Characteristics of G.729.1 codec . 33
5.4.4 Packet Loss Concealment algorithm (PLC) . 33
5.4.5 Supported bit rate in DECT . 34
5.5 Super-wideband MPEG-4 speech and audio coding . 34
5.5.1 Algorithm . 34
5.5.2 64 kbit/s, MPEG-4 ER AAC-LD codec . 34
5.5.3 32 kbit/s, MPEG-4 ER AAC-LD codec . 35
5.6 Narrowband, wideband, super-wideband, fullband, FBHR and ultra-band LC3plus speech and audio
coding . 35
5.6.1 Algorithm . 35
5.6.2 NB mode at 32 kbit/s gross bit rate and 10 ms frame size . 36
ETSI
---------------------- Page: 5 ----------------------
SIST EN 300 175-8 V2.9.1:2022
4 ETSI EN 300 175-8 V2.9.1 (2022-03)
5.6.3 WB mode at 32 kbit/s gross bit rate and 10 ms frame size . 36
5.6.4 SWB mode at 64 kbit/s gross bit rate and 10 ms frame size . 37
5.6.5 FB mode at 64 kbit/s gross bit rate and 10 ms frame size . 37
5.6.6 FB mode at 96 kbit/s gross bit rate and 10 ms frame size . 37
5.6.7 FB mode at 128 kbit/s gross bit rate and 10 ms frame size . 38
5.6.8 FB mode at 128 kbit/s gross bit rate and 5 ms frame size . 38
5.6.9 FB mode at 160 kbit/s gross bit rate and 5 ms frame size . 38
5.6.10 FB mode at 192 kbit/s gross bit rate and 5 ms frame size . 39
5.6.11 FB mode at 128 kbit/s gross bit rate and 2,5 ms frame size . 39
5.6.12 FB mode at 256 kbit/s gross bit rate and 2,5 ms frame size . 39
5.6.13 FBLFE mode at 32 kbit/s gross bit rate and 10 ms frame size . 39
5.6.14 FBLFE mode at 64 kbit/s gross bit rate and 5 ms frame size . 40
5.6.15 FB stereo mode at 128 kbit/s gross bit rate and 10 ms frame size . 40
5.6.16 FB stereo mode at 256 kbit/s gross bit rate and 5 ms frame size . 40
5.6.17 FB stereo mode at 320 kbit/s gross bit rate and 2,5 ms frame size . 40
5.6.18 FB stereo mode at 512 kbit/s gross bit rate and 2,5 ms frame size . 41
5.6.19 FBHR mode at 128 kbit/s gross bit rate and 10 ms frame size . 41
5.6.20 FBHR mode at 160 kbit/s gross bit rate and 10 ms frame size . 41
5.6.21 FBHR mode at 192 kbit/s gross bit rate and 10 ms frame size . 41
5.6.22 UBHR mode at 160 kbit/s gross bit rate and 10 ms frame size. 42
5.6.23 UBHR mode at 192 kbit/s gross bit rate and 10 ms frame size. 42
5.6.24 UBHR mode at 256 kbit/s gross bit rate and 10 ms frame size. 42
5.6.25 UBHR mode at 320 kbit/s gross bit rate and 10 ms frame size. 42
6 Transmission aspects . 43
6.1 Relative level . 43
6.2 Acoustic reference level . 43
6.3 Volume control . 43
7 Audio specifications . 43
7.1 Overall description . 43
7.1.1 Introduction to DECT audio specifications . 43
7.1.2 Introduction to the audio types . 43
7.1.3 List of Audio types . 44
7.1.4 Audio types for Portable Parts . 45
7.1.5 Audio types for Fixed Parts . 46
7.1.6 Complete DECT system . 46
7.1.7 Structure of the specification of the audio types . 47
7.1.8 Audio Types and codecs . 55
7.1.9 Audio Types and physical interfaces . 55
7.2 Audio types applicable to Portable Parts . 55
7.2.0 General . 55
7.2.1 Performance levels of DECT Portable Parts (handsets). 55
7.2.2 Type 0: Reference PP (RePP) . 57
7.2.3 PP Type 1a: "Classic" GAP narrowband handset . 57
7.2.3.1 Introduction . 57
7.2.3.2 Compatible services and codecs . 57
7.2.3.3 Specification. 57
7.2.4 PP Type 1b: "Improved" GAP narrowband handset . 58
7.2.4.1 Introduction . 58
7.2.4.2 Compatible services and codecs . 58
7.2.4.3 Specification. 58
7.2.5 PP Type 1c: HATS-tested "standard" narrowband handset . 58
7.2.5.1 Introduction . 58
7.2.5.2 Compatible services and codecs . 58
7.2.5.3 Specification. 58
7.2.6 PP Type 1d: HATS-tested "improved" narrowband handset . 59
7.2.6.1 Introduction . 59
7.2.6.2 Compatible services and codecs . 59
7.2.6.3 Specification. 59
7.2.7 PP Type 3a: HATS tested narrowband "standard" loudspeaking handsfree . 59
7.2.7.1 Introduction . 59
ETSI
---------------------- Page: 6 ----------------------
SIST EN 300 175-8 V2.9.1:2022
5 ETSI EN 300 175-8 V2.9.1 (2022-03)
7.2.7.2 Compatible services and codecs . 60
7.2.7.3 Specification. 60
7.2.8 PP Type 3b: HATS tested narrowband "improved" loudspeaking handsfree . 60
7.2.8.1 Introduction . 60
7.2.8.2 Compatible services and codecs . 60
7.2.8.3 Specification. 60
7.2.9 PP Type 2a: P.311-tested wideband handset. 60
7.2.9.1 Introduction . 60
7.2.9.2 Compatible services and codecs . 60
7.2.9.3 Specification. 60
7.2.10 PP Type 2b: HATS-tested "standard" wideband handset or headset . 61
7.2.10.1 Introduction . 61
7.2.10.2 Compatible services and codecs . 61
7.2.10.3 Specification. 61
7.2.11 PP Type 2c: HATS tested "improved" wideband handset or headset . 61
7.2.11.1 Introduction . 61
7.2.11.2 Compatible services and codecs . 61
7.2.11.3 Specification. 61
7.2.12 PP Type 4a: HATS tested wideband "standard" loudspeaking handsfree . 62
7.2.12.1 Introduction . 62
7.2.12.2 Compatible services and codecs . 62
7.2.12.3 Specification. 62
7.2.13 PP Type 4b: HATS tested wideband "improved" loudspeaking and handsfree . 62
7.2.13.1 Introduction . 62
7.2.13.2 Compatible services and codecs . 62
7.2.13.3 Specification. 62
7.2.14 PP Type 5a: super-wideband 14 kHz handset or headset. 63
7.2.14.1 Introduction . 63
7.2.14.2 Compatible services and codecs . 63
7.2.14.3 Specification. 63
7.2.15 PP Type 5b: super-wideband 14 kHz loudspeaking handsfree . 63
7.2.15.1 Introduction . 63
7.2.15.2 Compatible services and codecs . 63
7.2.15.3 Specification. 63
7.2.16 PP Type 6: PPs with external 2 wire, 3,1 kHz telephony interface . 63
7.2.16.1 Introduction . 63
7.2.16.2 Compatible services and codecs . 63
7.2.16.3 Specification. 63
7.2.17 PP Type 7a: fullband 20 kHz handset or headset . 63
7.2.17.1 Introduction . 63
7.2.17.2 Compatible services and codecs . 64
7.2.17.3 Specification. 64
7.2.18 PP Type 7b: fullband 20 kHz loudspeaking handsfree . 64
7.2.18.1 Introduction . 64
7.2.18.2 Compatible services and codecs . 64
7.2.18.3 Specification. 64
7.2.19 PP Type 7c, d, e, f: fullband 20 kHz stereo audio device . 64
7.2.19.1 Introduction . 64
7.2.19.2 Compatible services and codecs .
...
SLOVENSKI STANDARD
oSIST prEN 300 175-8 V2.8.5:2022
01-marec-2022
Digitalne izboljšane brezvrvične telekomunikacije (DECT) - Skupni vmesnik (CI) - 8.
del: Kodiranje in prenos govora in zvoka
Digital Enhanced Cordless Telecommunications (DECT) - Common Interface (CI) - Part
8: Speech and audio coding and transmission
Ta slovenski standard je istoveten z: ETSI EN 300 175-8 V2.8.5 (2021-12)
ICS:
33.070.30 Digitalne izboljšane Digital Enhanced Cordless
brezvrvične telekomunikacije Telecommunications (DECT)
(DECT)
oSIST prEN 300 175-8 V2.8.5:2022 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 300 175-8 V2.8.5:2022
---------------------- Page: 2 ----------------------
oSIST prEN 300 175-8 V2.8.5:2022
Draft ETSI EN 300 175-8 V2.8.5 (2021-12)
EUROPEAN STANDARD
Digital Enhanced Cordless Telecommunications (DECT);
Common Interface (CI);
Part 8: Speech and audio coding and transmission
---------------------- Page: 3 ----------------------
oSIST prEN 300 175-8 V2.8.5:2022
2 Draft ETSI EN 300 175-8 V2.8.5 (2021-12)
Reference
REN/DECT-00358
Keywords
7 kHz, audio, broadband, codec, DECT, handsfree,
IMT-2000, loudspeaking, mobility, narrowband,
quality, radio, speech, TDD, TDMA, telephony,
terminal
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - APE 7112B
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° w061004871
Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Notice of disclaimer & limitation of liability
The information provided in the present deliverable is directed solely to professionals who have the appropriate degree of
experience to understand and interpret its content in accordance with generally accepted engineering or
other professional standard and applicable regulations.
No recommendation as to products and services or vendors is made or should be implied.
In no event shall ETSI be held liable for loss of profits or any other incidental or consequential damages.
Any software contained in this deliverable is provided "AS IS" with no warranties, express or implied, including but not
limited to, the warranties of merchantability, fitness for a particular purpose and non-infringement of intellectual property
rights and ETSI shall not be held liable in any event for any damages whatsoever (including, without limitation, damages
for loss of profits, business interruption, loss of information, or any other pecuniary loss) arising out of or related to the use
of or inability to use the software.
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2021.
All rights reserved.
ETSI
---------------------- Page: 4 ----------------------
oSIST prEN 300 175-8 V2.8.5:2022
3 Draft ETSI EN 300 175-8 V2.8.5 (2021-12)
Contents
Intellectual Property Rights . 17
Foreword . 17
Modal verbs terminology . 17
1 Scope . 18
2 References . 18
2.1 Normative references . 18
2.2 Informative references . 20
3 Definition of terms, symbols and abbreviations . 22
3.1 Terms . 22
3.2 Symbols . 24
3.3 Abbreviations . 24
4 Configurations . 26
4.1 Reference configuration . 26
4.1.1 Basic configuration . 26
4.1.2 Portable Part (PP) . 27
4.1.2.1 Functional organization . 27
4.1.2.2 Volume control . 28
4.1.3 Fixed Part (FP) . 28
4.1.3.1 Digital interface . 28
4.1.3.2 Analog interface . 29
4.1.3.3 FP adaptive volume control . 30
4.1.3.4 Voice over IP (VoIP) interface . 30
4.2 Test configurations . 31
5 Encoding . 31
5.0 General . 31
5.1 32 kbit/s full term (ADPCM) G.726 . 31
5.1.1 Algorithm . 31
5.1.2 Bit sequence . 31
5.1.3 Characteristics of G.726 ADPCM codec . 31
5.2 64 kbit/s PCM G.711 . 32
5.2.1 Algorithm . 32
5.2.2 Bit sequence . 32
5.2.3 Characteristics of G.711 PCM codec . 32
5.2.4 Automatic detection of FAX/modem tone and switch to G.711 . 32
5.3 Wideband speech codec G.722 at 64 kbit/s . 32
5.3.0 General . 32
5.3.1 Algorithm . 32
5.3.2 Bit sequence . 33
5.3.3 Characteristics of G.722 wideband codec . 33
5.3.4 Optional Packet Loss Concealment algorithm (PLC) . 33
5.4 Wideband speech codec G.729.1 up to 32 kbit/s . 34
5.4.1 Algorithm . 34
5.4.2 Bit sequence . 34
5.4.3 Characteristics of G.729.1 codec . 34
5.4.4 Packet Loss Concealment algorithm (PLC) . 34
5.4.5 Supported bit rate in DECT . 35
5.5 Super-wideband MPEG-4 speech and audio coding . 35
5.5.1 Algorithm . 35
5.5.2 64 kbit/s, MPEG-4 ER AAC-LD codec . 35
5.5.3 32 kbit/s, MPEG-4 ER AAC-LD codec . 36
5.6 Narrowband, wideband, super-wideband, fullband, FBHR and ultra-band LC3plus speech and audio
coding . 36
5.6.1 Algorithm . 36
5.6.2 NB mode at 32 kbit/s gross bit rate and 10 ms frame size . 37
ETSI
---------------------- Page: 5 ----------------------
oSIST prEN 300 175-8 V2.8.5:2022
4 Draft ETSI EN 300 175-8 V2.8.5 (2021-12)
5.6.3 WB mode at 32 kbit/s gross bit rate and 10 ms frame size . 37
5.6.4 SWB mode at 64 kbit/s gross bit rate and 10 ms frame size . 38
5.6.5 FB mode at 64 kbit/s gross bit rate and 10 ms frame size . 38
5.6.6 FB mode at 96 kbit/s gross bit rate and 10 ms frame size . 38
5.6.7 FB mode at 128 kbit/s gross bit rate and 10 ms frame size . 39
5.6.8 FB mode at 128 kbit/s gross bit rate and 5 ms frame size . 39
5.6.9 FB mode at 160 kbit/s gross bit rate and 5 ms frame size . 39
5.6.10 FB mode at 192 kbit/s gross bit rate and 5 ms frame size . 40
5.6.11 FB mode at 128 kbit/s gross bit rate and 2,5 ms frame size . 40
5.6.12 FB mode at 256 kbit/s gross bit rate and 2,5 ms frame size . 40
5.6.13 FBLFE mode at 32 kbit/s gross bit rate and 10 ms frame size . 40
5.6.14 FBLFE mode at 64 kbit/s gross bit rate and 5 ms frame size . 41
5.6.15 FB stereo mode at 128 kbit/s gross bit rate and 10 ms frame size . 41
5.6.16 FB stereo mode at 256 kbit/s gross bit rate and 5 ms frame size . 41
5.6.17 FB stereo mode at 320 kbit/s gross bit rate and 2,5 ms frame size . 41
5.6.18 FB stereo mode at 512 kbit/s gross bit rate and 2,5 ms frame size . 42
5.6.19 FBHR mode at 128 kbit/s gross bit rate and 10 ms frame size . 42
5.6.20 FBHR mode at 160 kbit/s gross bit rate and 10 ms frame size . 42
5.6.21 FBHR mode at 192 kbit/s gross bit rate and 10 ms frame size . 42
5.6.22 UBHR mode at 160 kbit/s gross bit rate and 10 ms frame size. 43
5.6.23 UBHR mode at 192 kbit/s gross bit rate and 10 ms frame size. 43
5.6.24 UBHR mode at 256 kbit/s gross bit rate and 10 ms frame size. 43
5.6.25 UBHR mode at 320 kbit/s gross bit rate and 10 ms frame size. 43
6 Transmission aspects . 44
6.1 Relative level . 44
6.2 Acoustic reference level . 44
6.3 Volume control . 44
7 Audio specifications . 44
7.1 Overall description . 44
7.1.1 Introduction to DECT audio specifications . 44
7.1.2 Introduction to the audio types . 44
7.1.3 List of Audio types . 45
7.1.4 Audio types for Portable Parts . 46
7.1.5 Audio types for Fixed Parts . 47
7.1.6 Complete DECT system . 47
7.1.7 Structure of the specification of the audio types . 48
7.1.8 Audio Types and codecs . 56
7.1.9 Audio Types and physical interfaces . 56
7.2 Audio types applicable to Portable Parts . 56
7.2.0 General . 56
7.2.1 Performance levels of DECT Portable Parts (handsets). 56
7.2.2 Type 0: Reference PP (RePP) . 58
7.2.3 PP Type 1a: "Classic" GAP narrowband handset . 58
7.2.3.1 Introduction . 58
7.2.3.2 Compatible services and codecs . 58
7.2.3.3 Specification. 58
7.2.4 PP Type 1b: "Improved" GAP narrowband handset . 59
7.2.4.1 Introduction . 59
7.2.4.2 Compatible services and codecs . 59
7.2.4.3 Specification. 59
7.2.5 PP Type 1c: HATS-tested "standard" narrowband handset . 59
7.2.5.1 Introduction . 59
7.2.5.2 Compatible services and codecs . 59
7.2.5.3 Specification. 59
7.2.6 PP Type 1d: HATS-tested "improved" narrowband handset . 60
7.2.6.1 Introduction . 60
7.2.6.2 Compatible services and codecs . 60
7.2.6.3 Specification. 60
7.2.7 PP Type 3a: HATS tested narrowband "standard" loudspeaking handsfree . 60
7.2.7.1 Introduction . 60
ETSI
---------------------- Page: 6 ----------------------
oSIST prEN 300 175-8 V2.8.5:2022
5 Draft ETSI EN 300 175-8 V2.8.5 (2021-12)
7.2.7.2 Compatible services and codecs . 61
7.2.7.3 Specification. 61
7.2.8 PP Type 3b: HATS tested narrowband "improved" loudspeaking handsfree . 61
7.2.8.1 Introduction . 61
7.2.8.2 Compatible services and codecs . 61
7.2.8.3 Specification. 61
7.2.9 PP Type 2a: P.311-tested wideband handset. 61
7.2.9.1 Introduction . 61
7.2.9.2 Compatible services and codecs . 61
7.2.9.3 Specification. 61
7.2.10 PP Type 2b: HATS-tested "standard" wideband handset or headset . 62
7.2.10.1 Introduction . 62
7.2.10.2 Compatible services and codecs . 62
7.2.10.3 Specification. 62
7.2.11 PP Type 2c: HATS tested "improved" wideband handset or headset . 62
7.2.11.1 Introduction . 62
7.2.11.2 Compatible services and codecs . 62
7.2.11.3 Specification. 62
7.2.12 PP Type 4a: HATS tested wideband "standard" loudspeaking handsfree . 63
7.2.12.1 Introduction . 63
7.2.12.2 Compatible services and codecs . 63
7.2.12.3 Specification. 63
7.2.13 PP Type 4b: HATS tested wideband "improved" loudspeaking and handsfree . 63
7.2.13.1 Introduction . 63
7.2.13.2 Compatible services and codecs . 63
7.2.13.3 Specification. 63
7.2.14 PP Type 5a: super-wideband 14 kHz handset or headset. 64
7.2.14.1 Introduction . 64
7.2.14.2 Compatible services and codecs . 64
7.2.14.3 Specification. 64
7.2.15 PP Type 5b: super-wideband 14 kHz loudspeaking handsfree . 64
7.2.15.1 Introduction . 64
7.2.15.2 Compatible services and codecs . 64
7.2.15.3 Specification. 64
7.2.16 PP Type 6: PPs with external 2 wire, 3,1 kHz telephony interface . 64
7.2.16.1 Introduction . 64
7.2.16.2 Compatible services and codecs . 64
7.2.16.3 Specification. 64
7.2.17 PP Type 7a: fullband 20 kHz handset or headset . 64
7.2.17.1 Introduction . 64
7.2.17.2 Compatible services and codecs . 65
7.2.17.3 Specification. 65
7.2.18 PP Type 7b: fullband 20 kHz loudspeaking handsfree . 65
7.2.18.1 Introduction . 65
7.2.18.2 Compatible services and codecs . 65
7.2.18.3 Specification. 65
7.2.19 PP Type 7c, d, e, f: fullband 20 kHz stereo audio device . 65
7.2.19.1 Introduction . 65
7.2.19.2 Compatible services and codecs . 65
7.2.19.3 Specification. 65
7.2.20 PP Type 7g: FBHR 24 kHz headset device .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.