SIST EN ISO 8207:2027
(Main)Gas welding equipment - Specification for hose assemblies for equipment for welding, cutting and allied processes (ISO 8207:2026)
- Abstract
This document specifies the performance and test requirements of hose assemblies supplied in assembled condition using rubber hose according to ISO 3821 up to and including nominal size 20,0, for gas welding, cutting and allied processes.
This document is not applicable to high-pressure hose assemblies upstream of the pressure regulators.
- Status
- Not Published
- Public Enquiry End Date
- 19-Dec-2025
- Technical Committee
- VAR - Welding
- Current Stage
- 6060 - National Implementation/Publication (Adopted Project)
- Start Date
- 20-Nov-2026
- Due Date
- 25-Jan-2027
SIST EN ISO 8207:2027 is the Slovenian adoption of ISO 8207 for hose assemblies used in gas welding, cutting and allied processes. It specifies the performance, construction, marking, and test requirements for assembled rubber-hose hose assemblies up to nominal size 20,0. The document is for manufacturers, testers, and users who need defined hose assemblies for equipment downstream of pressure regulators.
What does SIST EN ISO 8207:2027 specify?
SIST EN ISO 8207:2027 specifies hose assemblies supplied in assembled condition for gas welding, cutting and allied processes. It applies to hose assemblies using rubber hose according to ISO 3821 up to and including nominal size 20,0.
SIST EN ISO 8207:2027 does not apply to high-pressure hose assemblies upstream of the pressure regulators. In practice, that separates the document from upstream high-pressure service and keeps its requirements focused on the assembled hose used at the equipment side.
The document is organized into:
- Clause 1 Scope
- Clause 2 Normative references
- Clause 3 Terms and definitions
- Clause 4 Construction
- Clause 5 Marking
- Clause 6 Performance requirements, operational criteria and test methods
- Annex A, informative, with examples of kinking protection design
- Bibliography
| Annex | What it covers |
|---|---|
| Annex A | Examples of kinking protection design for hose assemblies |
What are the key requirements of SIST EN ISO 8207:2027?
SIST EN ISO 8207:2027 combines construction rules with type-test requirements. The most important points are the hose materials and fittings, the marking, and the three performance checks for leakage and resistance to separation.
Construction and materials
SIST EN ISO 8207:2027 requires hose assemblies to use hoses complying with ISO 3821 and appropriate hose fittings. Components in direct contact with the gas supply have to comply with ISO 9539, and hose mounting device materials must be corrosion resistant or protected against corrosion.
The standard also prohibits greases or pastes during manufacture. That matters because contamination can affect sealing, assembly quality, or service life.
Hose tail and assembly design
SIST EN ISO 8207:2027 requires the hose tail profile to avoid sharp edges that could damage the hose during assembly or use. The hose tail must also provide enough mounting area for secure positioning of the hose mounting device.
The hose must be secured to the hose tail with a compatible hose mounting device that provides repeatable resistance to separation under axial load. Worm drive screws and similar detachable clips or clamps are not allowed for securing the hose to the hose tail.
Marking
SIST EN ISO 8207:2027 requires durable marking with the manufacturer name or trade mark and a reference to ISO 8207. The marking is placed on the end fitting or on a separate band fixed to the hose next to the end fitting.
The standard also allows date coding, such as the last two digits of the year of assembly plus month or week. That helps trace production and service history.
Performance requirements and test methods
SIST EN ISO 8207:2027 says the tests in Clause 6 apply to type testing. For gas tightness, the hose assembly is tested in accordance with ISO 9090 and must meet the maximum permissible leakage rate from that standard.
For resistance to separation under pressure, the hose assembly is tested for one minute at three times the maximum working pressure at laboratory temperature, using a test piece with 500 mm free length. The hose must not separate from the hose tail.
For resistance to separation under axial load, an unpressurized hose assembly is loaded in the axial direction for 2 minutes. The load depends on nominal size, and the hose must not separate, fracture, or lose gas tightness after the test.
What terms does SIST EN ISO 8207:2027 define?
SIST EN ISO 8207:2027 uses terms from ISO 8330 and adds one document-specific definition.
- Hose assembly - a hose with a hose fitting attached to one or both ends.
- Assembled condition - the state in which the hose is supplied as a completed assembly rather than as hose alone.
- Gas tightness - the sealing condition checked by the leakage test in Clause 6.2.
- Resistance to separation under pressure - the ability of the hose to stay attached to the hose tail when pressurized.
- Resistance to separation under axial load - the ability of the hose to stay attached when pulled in line with the hose axis.
- Kinking protection - an added design feature shown in Annex A to reduce damage near the hose tail.
Who uses SIST EN ISO 8207:2027?
SIST EN ISO 8207:2027 is used by manufacturers of gas welding equipment and hose assemblies, because it defines how the assembly is built, marked, and tested. It is also used by test laboratories and quality teams that need type-testing procedures and acceptance criteria.
Buyers, specifiers, and inspectors use it when they need to compare hose assemblies on a common technical basis. In practice, it helps them choose assemblies for welding, cutting, and allied processes while staying within the scope of rubber-hose assemblies supplied in assembled condition.
What changed in SIST EN ISO 8207:2027 from the previous edition?
SIST EN ISO 8207:2027 replaces ISO 8207:1996 and is technically revised. The foreword states these changes:
- the scope was clarified to limit the document to rubber hoses according to ISO 3821 up to nominal size 20,0
- a definition of assembled hose was added in Clause 3 and aligned with ISO 15296:2017
- Clause 4 Construction was modified
- the former Clause 5 Operational criteria was moved into Clause 6
- a new Clause 5 Marking was added
- nominal sizes 12,5, 16,0 and 20,0 and their axial loads were added to Table 1
- the old informative annex on hose tail dimensions was deleted
- a new informative annex with examples of kinking protection design was added
Which standards are used with SIST EN ISO 8207:2027?
SIST EN ISO 8207:2027 refers to four normative references that supply needed terms, materials, and test methods:
- ISO 3821 - provides the rubber hose specification used for the hose in the assembly
- ISO 8330 - provides vocabulary for rubber and plastics hoses and hose assemblies
- ISO 9090 - provides the gas tightness test and leakage acceptance basis
- ISO 9539 - provides material requirements for equipment used in gas welding, cutting and allied processes
The bibliography also cites ISO/TR 28821 for hose connections listed as standardized or commonly used, which is useful background for connection choices. The foreword also notes alignment of the assembled-hose definition with ISO 15296:2017.
What does the SIST EN ISO 8207:2027 document contain?
SIST EN ISO 8207:2027 contains construction requirements, marking rules, and three performance test areas. It also includes two figures showing hose assembly configurations with a permanent ferrule or a permanent clamp, and a table giving axial loads by nominal size.
Annex A gives examples of kinking protection designs for special applications. That annex is informative, so it helps designers understand one way to reduce damage near the hose tail without adding a mandatory design rule.
Relations
- Effective Date
- 01-Jan-2027
- Effective Date
- 14-Oct-2026
- Effective Date
- 14-Oct-2026
- Effective Date
- 14-Oct-2026
Get Certified
Connect with accredited certification bodies for this standard
DIN CERTCO
DIN Group product certification.

DVS-ZERT GmbH
German welding certification society.
Institut za varilstvo d.o.o. (Welding Institute)
Slovenia's leading welding institute since 1952. ISO 3834, EN 1090, pressure equipment certification, NDT personnel, welder qualification. Only IIW Au
Sponsored listings
Frequently Asked Questions
SIST EN ISO 8207:2027 is a draft published by the Slovenian Institute for Standardization (SIST). Its full title is "Gas welding equipment - Specification for hose assemblies for equipment for welding, cutting and allied processes (ISO 8207:2026)". This standard covers: This document specifies the performance and test requirements of hose assemblies supplied in assembled condition using rubber hose according to ISO 3821 up to and including nominal size 20,0, for gas welding, cutting and allied processes. This document is not applicable to high-pressure hose assemblies upstream of the pressure regulators.
This document specifies the performance and test requirements of hose assemblies supplied in assembled condition using rubber hose according to ISO 3821 up to and including nominal size 20,0, for gas welding, cutting and allied processes. This document is not applicable to high-pressure hose assemblies upstream of the pressure regulators.
SIST EN ISO 8207:2027 is classified under the following ICS (International Classification for Standards) categories: 23.040.70 - Hoses and hose assemblies; 25.160.30 - Welding equipment; 83.140.40 - Hoses. The ICS classification helps identify the subject area and facilitates finding related standards.
SIST EN ISO 8207:2027 has the following relationships with other standards: It is inter standard links to SIST EN 1256:2006, SIST-TP CEN/TR 15339-3:2015, SIST EN 560:2018, SIST EN 17931:2026. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
SIST EN ISO 8207:2027 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
SLOVENSKI STANDARD
oSIST prEN ISO 8207:2025
01-december-2025
Oprema za plamensko varjenje - Popis za cevne vode za opremo za varjenje,
rezanje in sorodne postopke (ISO/DIS 8207:2025)
Gas welding equipment - Specification for hose assemblies for equipment for welding,
cutting and allied processes (ISO/DIS 8207:2025)
Gasschweißgeräte - Festlegungen für Schlauchleitungen für Ausrüstungen für
Schweißen, Schneiden und verwandte Verfahren (ISO/DIS 8207:2025)
Matériel de soudage au gaz - Spécifications relatives aux flexibles pour matériel de
soudage, coupage et techniques connexes (ISO/DIS 8207:2025)
Ta slovenski standard je istoveten z: prEN ISO 8207
ICS:
25.160.30 Varilna oprema Welding equipment
83.140.40 Gumene cevi Hoses
oSIST prEN ISO 8207:2025 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
oSIST prEN ISO 8207:2025
oSIST prEN ISO 8207:2025
DRAFT
International
Standard
ISO/DIS 8207
ISO/TC 44/SC 8
Gas welding equipment —
Secretariat: DIN
Specification for hose assemblies
Voting begins on:
for equipment for welding, cutting
2025-10-13
and allied processes
Voting terminates on:
2026-01-05
Matériel de soudage au gaz — Spécifications relatives aux
assemblages de tuyaux souples sur les douilles porte-tuyau pour
matériel de soudage, coupage et techniques connexes
ICS: 83.140.40; 25.160.30
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document has not been edited by the ISO Central Secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
NATIONAL REGULATIONS.
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Reference number
ISO/DIS 8207:2025(en)
oSIST prEN ISO 8207:2025
DRAFT
ISO/DIS 8207:2025(en)
International
Standard
ISO/DIS 8207
ISO/TC 44/SC 8
Gas welding equipment —
Secretariat: DIN
Specification for hose assemblies
Voting begins on:
for equipment for welding, cutting
and allied processes
Voting terminates on:
Matériel de soudage au gaz — Spécifications relatives aux
assemblages de tuyaux souples sur les douilles porte-tuyau pour
matériel de soudage, coupage et techniques connexes
ICS: 83.140.40; 25.160.30
THIS DOCUMENT IS A DRAFT CIRCULATED
FOR COMMENTS AND APPROVAL. IT
IS THEREFORE SUBJECT TO CHANGE
AND MAY NOT BE REFERRED TO AS AN
INTERNATIONAL STANDARD UNTIL
PUBLISHED AS SUCH.
This document has not been edited by the ISO Central Secretariat.
IN ADDITION TO THEIR EVALUATION AS
BEING ACCEPTABLE FOR INDUSTRIAL,
© ISO 2025
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
STANDARDS MAY ON OCCASION HAVE TO
ISO/CEN PARALLEL PROCESSING
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
BE CONSIDERED IN THE LIGHT OF THEIR
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
or ISO’s member body in the country of the requester.
NATIONAL REGULATIONS.
ISO copyright office
RECIPIENTS OF THIS DRAFT ARE INVITED
CP 401 • Ch. de Blandonnet 8
TO SUBMIT, WITH THEIR COMMENTS,
CH-1214 Vernier, Geneva
NOTIFICATION OF ANY RELEVANT PATENT
Phone: +41 22 749 01 11
RIGHTS OF WHICH THEY ARE AWARE AND TO
PROVIDE SUPPORTING DOCUMENTATION.
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland Reference number
ISO/DIS 8207:2025(en)
ii
oSIST prEN ISO 8207:2025
ISO/DIS 8207:2025(en)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Construction . 3
4.1 Materials .3
4.2 Design of hose tail and hose assembly .3
4.2.1 General .3
4.2.2 Hose tail .3
4.2.3 Hose assembly .4
5 Marking . . 4
6 Performance requirements, operational criteria and test methods . 4
6.1 General .4
6.2 Gas tightness .4
6.2.1 Test method .4
6.2.2 Acceptance requirements .4
6.3 Resistance to separation under pressure .4
6.3.1 Test method .4
6.3.2 Acceptance requirements .4
6.4 Resistance to separation under axial load .5
6.4.1 Test method .5
6.4.2 Acceptance requirements .5
Annex A (informative) Examples of kinking protection design . 6
Bibliography . 7
iii
oSIST prEN ISO 8207:2025
ISO/DIS 8207:2025(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and
...



