SIST EN 61000-6-4:2007/A1:2011
(Amendment)Electromagnetic compatibility (EMC) - Part 6-4: Generic standards - Emission standard for industrial environments
Electromagnetic compatibility (EMC) - Part 6-4: Generic standards - Emission standard for industrial environments
This part of IEC 61000 for EMC emission requirements applies to electrical and electronic apparatus intended for use in industrial environments as described below. Emission requirements in the frequency range 0 Hz to 400 GHz are covered. No measurement needs to be performed at frequencies where no requirement is specified. This generic EMC emission standard is applicable if no relevant dedicated product or productfamily EMC emission standard exists. This standard applies to a apparatus intended to be connected to a power network supplied from a high or medium voltage transformer dedicated to the supply of an installation feeding manufacturing or similar plant, and intended to operate in or in proximity to industrial locations, as described below. This standard applies also to apparatus, which is battery operated and intended to be used in industrial locations. The environments encompassed by this standard are industrial, both indoor and outdoor. Industrial locations are in addition characterised by the existence of one or more of the following examples: - industrial, scientific and medical (ISM)1)) apparatus; - heavy inductive or capacitive loads that are frequently switched; - high currents and associated magnetic fields. The object of this standard is to define the emission test requirements for apparatus defined in the scope in relation to continuous and transient, conducted and radiated disturbances. The emission requirements have been selected so as to ensure that disturbances generated by apparatus operating normally in industrial locations do not exceed a level that could prevent other apparatus from operating as intended. Fault conditions of apparatus are not taken into account. Not all disturbance phenomena have been included for testing purposes in this standard but only those considered as relevant for the equipment covered by this standard. These requirements represent essential electromagnetic compatibility emission requirements.
Elektromagnetische Verträglichkeit (EMV) - Teil 6-4: Fachgrundnormen - Störaussendung für Industriebereiche
Compatibilité électromagnétique (CEM) - Partie 6-4: Normes génériques - Norme sur l'émission pour les environnements industriels
Elektromagnetna združljivost (EMC) - 6-4. del: Osnovni (generični) standardi - Standard oddajanja motenj v industrijskih okoljih - Dodatek A1 (IEC 61000-6-4:2006/A1:2010)
Ta del IEC 61000 za zahteve glede elektromagnetne združljivosti pri oddajanju motenj velja za električne in elektronske aparate, ki se uporabljajo v spodaj opisanih industrijskih okoljih. Zajete so zahteve za oddajanje motenj v frekvenčnem razponu od 0 Hz do 400 GHz. Kjer zahteve niso določene, ni potrebno nobeno merjenje. Ta rodovni standard za elektromagnetno združljivost pri oddajanju motenj velja, če ne obstaja noben ustrezni namenski standard za elektromagnetno združljivost pri oddajanju motenj za posamezen proizvod ali družino proizvodov. Ta standard velja za aparate, povezane z električnim omrežjem, ki ga napaja visoko- ali srednjenapetostni transformator, namenjen napajanju inštalacij, ki oskrbujejo proizvodne ali podobne obrate in delujejo v industrijskih lokacijah ali v njihovi bližini, kot je opisano spodaj. Ta standard velja tudi za aparate, ki delujejo na baterije in se uporabljajo na industrijskih lokacijah. Okolja, ki jih zajema ta standard, so industrijska, v zaprtih prostorih in na prostem. Za industrijske lokacije je dodatno značilen eden ali več spodnjih primerov: - industrijski, znanstveni in medicinski (ISM)1)) aparati; - težke induktivne ali kapacitivne obremenitve, ki se pogosto preklapljajo; - visoki tokovi in povezana magnetna polja. Cilj tega standarda je opredeliti zahteve za preskušanje oddajanja motenj za aparate, opredeljene v tem okviru, v zvezi z neprekinjenimi in prehodnimi, vodenimi ter sevanimi motnjami. Zahteve za oddajanje motenj so bile izbrane tako, da zagotovijo, da motnje, ki jih proizvaja aparat, ki deluje normalno v industrijski lokaciji, ne presežejo stopnje, nad katero drugi aparati ne morejo delovati, kot je predvideno. Okoliščine okvare aparata niso upoštevane. Vsi pojavi motenj za namene preskušanja niso bili vključeni v ta standard; vključeni so le tisti, ki veljajo za ustrezne za opremo, ki jo zajema ta standard. Te zahteve so bistvene za elektromagnetno združljivost pri oddajanju motenj.
General Information
- Status
- Published
- Publication Date
- 11-Apr-2011
- Technical Committee
- EMC - Electromagnetic compatibility
- Current Stage
- 6100 - Translation of adopted SIST standards (Adopted Project)
- Start Date
- 27-Oct-2015
- Due Date
- 25-Oct-2016
- Completion Date
- 22-Apr-2016
Relations
- Effective Date
- 01-Nov-2019
- Effective Date
- 01-May-2011
Frequently Asked Questions
SIST EN 61000-6-4:2007/A1:2011 is a standard – translation published by the Slovenian Institute for Standardization (SIST). Its full title is "Electromagnetic compatibility (EMC) - Part 6-4: Generic standards - Emission standard for industrial environments". This standard covers: This part of IEC 61000 for EMC emission requirements applies to electrical and electronic apparatus intended for use in industrial environments as described below. Emission requirements in the frequency range 0 Hz to 400 GHz are covered. No measurement needs to be performed at frequencies where no requirement is specified. This generic EMC emission standard is applicable if no relevant dedicated product or productfamily EMC emission standard exists. This standard applies to a apparatus intended to be connected to a power network supplied from a high or medium voltage transformer dedicated to the supply of an installation feeding manufacturing or similar plant, and intended to operate in or in proximity to industrial locations, as described below. This standard applies also to apparatus, which is battery operated and intended to be used in industrial locations. The environments encompassed by this standard are industrial, both indoor and outdoor. Industrial locations are in addition characterised by the existence of one or more of the following examples: - industrial, scientific and medical (ISM)1)) apparatus; - heavy inductive or capacitive loads that are frequently switched; - high currents and associated magnetic fields. The object of this standard is to define the emission test requirements for apparatus defined in the scope in relation to continuous and transient, conducted and radiated disturbances. The emission requirements have been selected so as to ensure that disturbances generated by apparatus operating normally in industrial locations do not exceed a level that could prevent other apparatus from operating as intended. Fault conditions of apparatus are not taken into account. Not all disturbance phenomena have been included for testing purposes in this standard but only those considered as relevant for the equipment covered by this standard. These requirements represent essential electromagnetic compatibility emission requirements.
This part of IEC 61000 for EMC emission requirements applies to electrical and electronic apparatus intended for use in industrial environments as described below. Emission requirements in the frequency range 0 Hz to 400 GHz are covered. No measurement needs to be performed at frequencies where no requirement is specified. This generic EMC emission standard is applicable if no relevant dedicated product or productfamily EMC emission standard exists. This standard applies to a apparatus intended to be connected to a power network supplied from a high or medium voltage transformer dedicated to the supply of an installation feeding manufacturing or similar plant, and intended to operate in or in proximity to industrial locations, as described below. This standard applies also to apparatus, which is battery operated and intended to be used in industrial locations. The environments encompassed by this standard are industrial, both indoor and outdoor. Industrial locations are in addition characterised by the existence of one or more of the following examples: - industrial, scientific and medical (ISM)1)) apparatus; - heavy inductive or capacitive loads that are frequently switched; - high currents and associated magnetic fields. The object of this standard is to define the emission test requirements for apparatus defined in the scope in relation to continuous and transient, conducted and radiated disturbances. The emission requirements have been selected so as to ensure that disturbances generated by apparatus operating normally in industrial locations do not exceed a level that could prevent other apparatus from operating as intended. Fault conditions of apparatus are not taken into account. Not all disturbance phenomena have been included for testing purposes in this standard but only those considered as relevant for the equipment covered by this standard. These requirements represent essential electromagnetic compatibility emission requirements.
SIST EN 61000-6-4:2007/A1:2011 is classified under the following ICS (International Classification for Standards) categories: 33.100.10 - Emission. The ICS classification helps identify the subject area and facilitates finding related standards.
SIST EN 61000-6-4:2007/A1:2011 has the following relationships with other standards: It is inter standard links to SIST EN IEC 61000-6-4:2019, SIST EN 61000-6-4:2007. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
SIST EN 61000-6-4:2007/A1:2011 is associated with the following European legislation: EU Directives/Regulations: 1999/5/EC, 2004/108/EC, 2004/108/EU, 2010-01-3290, 2014/30/EU, 2014/53/EU; Standardization Mandates: M/404, M/490, M/536, M/552. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.
You can purchase SIST EN 61000-6-4:2007/A1:2011 directly from iTeh Standards. The document is available in PDF format and is delivered instantly after payment. Add the standard to your cart and complete the secure checkout process. iTeh Standards is an authorized distributor of SIST standards.
Standards Content (Sample)
SLOVENSKI SIST EN 61000-6-4:2007/A1
STANDARD
maj 2011
Elektromagnetna združljivost (EMC) – 6-4. del: Osnovni (generični) standardi
– Standard oddajanja motenj v industrijskih okoljih – Dopolnilo A1
(IEC 61000-6-4:2006/A1:2010)
Electromagnetic compatibility (EMC) – Part 6-4: Generic standards –
Emission standard for industrial environments (IEC 61000-6-4:2006/A1:2010)
Compatibilité électromagnétique (CEM) – Partie 6-4: Normes génériques –
Norme sur l'émission pour les environnements industriels
(CEI 61000-6-4:2006/A1:2010)
Elektromagnetische Verträglichkeit (EMV) – Teil 6-4: Fachgrundnormen –
Störaussendung für Industriebereiche (IEC 61000-6-4:2006/A1:2010)
Referenčna oznaka
ICS 33.100.10 SIST EN 61000-6-4:2007/A1:2011 (sl)
Nadaljevanje na straneh II in III ter od 1 do 14
© 2016-05. Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
SIST EN 61000-6-4:2007/A1 : 2011
NACIONALNI UVOD
Dopolnilo SIST EN 61000-6-4:2007/A1 (sl), Elektromagnetna združljivost (EMC) – 6-4. del: Osnovni
(generični) standardi – Standard oddajanja motenj v industrijskih okoljih – Dopolnilo A1 (IEC 61000-6-
4:2006/A1:2010), 2011, ima status slovenskega dopolnila in je istoveten evropskemu dopolnilu EN
61000-6-4:2007/A1 (en), Electromagnetic compatibility (EMC) – Part 6-4: Generic standards –
Emission standard for industrial environments (IEC 61000-6-4:2006/A1:2010), 2011.
NACIONALNI PREDGOVOR
Evropsko dopolnilo EN 61000-6-4:2007/A1:2011 je pripravil tehnični odbor CLC/TC 210
Elektromagnetna združljivost (EMC). Slovensko dopolnilo SIST EN 61000-6-4:2007/A1:2011 je prevod
evropskega dopolnila EN 61000-6-4:2007/A1:2011. V primeru spora glede besedila slovenskega
prevoda v tem dopolnilu je odločilen izvirno evropsko dopolnilo v angleškem jeziku. Slovensko izdajo
dopolnila je potrdil tehnični odbor SIST/TC EMC Elektromagnetna združljivost.
Odločitev za privzem tega dopolnila je v maju 2011 sprejel tehnični odbor SIST/TC EMC
Elektromagnetna združljivost.
ZVEZA Z NACIONALNIMI STANDARDI
S privzemom tega evropskega dopolnila veljajo za omejeni namen referenčnih standardov vsi
standardi, navedeni v izvirniku, razen tistih, ki so že sprejeti v nacionalno standardizacijo:
SIST EN 61000-4-20:2011 Elektromagnetna združljivost (EMC) – 4-20. del: Preskusne in merilne
tehnike – Preskušanje oddajanja in odpornosti v prečnih
elektromagnetnih (TEM) valovodih (IEC 61000-4-20:2010)
SIST EN 55014-1:2007 Elektromagnetna združljivost – Zahteve za (električne) gospodinjske
aparate, električna ročna orodja in podobne aparate – 1. del:
Oddajanje (CISPR 14-1:2005)
SIST EN 55016-1-1:2010 Specifikacija merilnih naprav in metod za merjenje radijskih motenj in
odpornosti – 1-1. del: Merilne naprave za merjenje radijskih motenj in
odpornosti – Merilne naprave
SIST EN 55016-1-4:2007 Specifikacija za merilne naprave in metode za merjenje
SIST EN 55016-1- radiofrekvenčnih motenj in odpornosti – 1-4. del: Merilne naprave za
4:2007/A1:2008 merjenje radiofrekvenčnih motenj in odpornosti – Pomožna oprema –
Sevane motnje
SIST EN 55011:2010 Industrijska, znanstvena in medicinska (ISM) radiofrekvenčna oprema
– Karakteristike občutljivosti za radijske motnje – Mejne vrednosti in
merilne metode (CISPR 11:2009, spremenjen)
SIST EN 55016-2-1:2009 Specifikacija za merilne naprave in metode za merjenje radijskih
motenj in odpornosti – 2-1. del: Metode za merjenje radijskih motenj in
odpornosti – Merjenje motenj po vodnikih
SIST EN 55016-2-3:2007 Specifikacija merilnih naprav in metod za merjenje radijskih motenj in
odpornosti – 2-3. del: Metode za merjenje radijskih motenj in
odpornosti – Merjenje sevanih motenj (CISPR 16-2-3:2006)
SIST EN 55016-4-2:2005 Specifikacija za merilne naprave in metode za merjenje radijskih
motenj in odpornosti – 4-2. del: Modeliranje negotovosti, statistike in
mejnih vrednosti – Negotovost pri meritvah EMC (CISPR 16-4-2:2003)
SIST EN 55022:2011 Oprema za informacijsko tehnologijo – Karakteristike občutljivosti za
radijske motnje – Mejne vrednosti in merilne metode
II
SIST EN 61000-6-4:2007/A1 : 2011
OSNOVA ZA IZDAJO DOPOLNILA
– privzem dopolnila EN 61000-6-4:2007/A1:2011
OPOMBE
– Povsod, kjer se v besedilu dopolnila uporablja izraz "evropsko" ali "mednarodno" dopolnilo, v
– Nacionalni uvod in nacionalni predgovor nista sestavni del dopolnila.
– Ta nacionalni dokument je istoveten EN 61000-6-4:2007/A1:2011 in je objavljen z dovoljenjem
CEN/CENELEC
Upravni center
Avenue Marnix 17
B-1000 Bruselj
This national document is identical with EN 61000-6-4:2007/A1:2011 and is published with the
permission of
CEN/CENELEC
Management Centre
Avenue Marnix 17
B -1000 Brussels
III
EVROPSKI STANDARD EN 61000-6-4/A1
EUROPEAN STANDARD
NORME EUROPÉENNE
EUROPÄISCHE NORM februar 2011
ICS: 33.100.10
Slovenska izdaja
Elektromagnetna združljivost (EMC) – 6-4. del: Osnovni (generični) standardi –
Standard oddajanja motenj v industrijskih okoljih – Dopolnilo A1
(IEC 61000-6-4:2006/A1:2010
Electromagnetic compatibility Compatibilité électromagnétique Elektromagnetische Verträglichkeit
(EMC) – Part 6-4: Generic (CEM) – Partie 6-4: Normes (EMV) – Teil 6-4: Fachgrundnormen
standards – Emission standard génériques – Norme sur l'émission – Störaussendung für
for industrial environments pour les environnements industriels Industriebereiche
(IEC 61000-6-4:2006/A1:2010) (CEI 61000-6-4:2006/A1:2010) (IEC 61000-6-4:2006/A1:2010)
To dopolnilo A1 spreminja evropski standard EN 61000-6-4:2007 in ga je CENELEC sprejel
12. januarja 2011. Člani CENELEC morajo izpolnjevati notranje predpise CEN/CENELEC, s katerimi
so predpisani pogoji za privzem tega dopolnila na nacionalno raven brez kakršnihkoli sprememb.
Najnovejši seznami teh nacionalnih standardov z njihovimi bibliografskimi podatki se na zahtevo lahko
dobijo pri Centralnem sekretariatu ali kateremkoli članu CENELEC.
To dopolnilo obstaja v treh uradnih izdajah (angleški, francoski in nemški). Izdaje v drugih jezikih, ki jih
člani CENELEC na lastno odgovornost prevedejo in izdajo ter prijavijo pri Centralnem sekretariatu,
veljajo kot uradne izdaje.
Člani CENELEC so nacionalni elektrotehniški komiteji Avstrije, Belgije, Bolgarije, Cipra, Češke
republike, Danske, Estonije, Finske, Francije, Grčije, Hrvaške, Islandije, Irske, Italije, Latvije, Litve,
Luksemburga, Madžarske, Malte, Nemčije, Nizozemske, Norveške, Poljske, Portugalske, Romunije,
Slovaške, Slovenije, Španije, Švedske, Švice in Združenega kraljestva.
CENELEC
Evropski komite za standardizacijo v elektrotehniki
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Upravni center: Avenue Marnix 17, B-1000 Bruselj
© 2011 CENELEC Lastnice avtorskih pravic so vse države članice CENELEC. Ref. št. EN 61000-6-3:2007/A1:2011 E
SIST EN 61000-6-4:2007/A1 : 2011
Predgovor k evropskemu dopolnilu
Besedilo dokumenta CISPR/H/205/FDIS, prihodnje dopolnilo 1 k IEC 61000-6-4:2006, ki ga je pripravil
pododbor CISPR SC H Meje za zaščito radijskih storitev, je CENELEC po vzporednem glasovanju v
IEC in CENELEC 1. januarja 2011 sprejel kot dopolnilo A1 k EN 61000-6-4:2007.
Opozoriti je treba na možnost, da bi lahko bil kateri od elementov tega dokumenta predmet patentnih
pravic. CEN in CENELEC nista odgovorna za identificiranje nobene od teh patentnih pravic.
Določena sta bila naslednja datuma:
– zadnji datum, do katerega mora dopolnilo dobiti status
nacionalnega dopolnila bodisi z objavo istovetnega besedila
ali z razglasitvijo (dop) 2011-10-01
– zadnji datum, ko je treba razveljaviti nacionalne standarde,
ki so z dopolnilom v nasprotju (dow) 2014-01-01
Dodatek ZA je dodal CENELEC.
Razglasitvena objava
Besedilo dopolnila 1:2010 k mednarodnemu standardu IEC 61000-6-4:2006 je CENELEC odobril kot
dopolnilo k evropskemu standardu brez kakršnihkoli sprememb.
SIST EN 61000-6-4:2007/A1 : 2011
Dodatek ZA
(normativni)
Sklicevanje na mednarodne publikacije z njihovimi ustreznimi evropskimi
publikacijami
Pri uporabi tega dokumenta so nujno potrebni naslednji referenčni dokumenti. Pri datiranih
sklicevanjih velja le navedena izdaja dokumenta. Pri nedatiranih sklicevanjih se uporablja zadnja
izdaja publikacije (vključno z dopolnili).
OPOMBA: Kadar je mednarodna publikacija spremenjena in so spremembe označene z (mod), se uporablja ustrezni
dokument EN/HD.
Standard Leto Naslov EN/HD Leto
Dodati obstoječemu seznamu naslednja nova sklicevanja:
IEC 60050-161 - Mednarodni elektrotehniški slovar (IEV) – - -
Poglavje 161: Elektromagnetna združljivost
IEC 61000-4-20 2010 Elektromagnetna združljivost (EMC) – EN 61000-4-20 2010
4-20. del: Preskusne in merilne tehnike –
Preskušanje oddajanja in odpornosti v
prečnih elektromagnetnih (TEM) valovodih
CISPR 14-1 2005 Elektromagnetna združljivost – Zahteve za EN 55014-1 2006
(električne) gospodinjske aparate,
električna ročna orodja in podobne aparate
– 1. del: Oddajanje
CISPR 16-1-1 2010 Specifikacija merilnih naprav in metod za EN 55016-1-1 2010
merjenje radijskih motenj in odpornosti –
1-1. del: Merilne naprave za merjenje
radijskih motenj in odpornosti – Merilne
naprave
CISPR 16-1-4 + A1 2007 Specifikacija za merilne naprave in metode EN 55016-1-4 + 2007
1)
2007 za merjenje radijskih motenj in odpornosti – A1 2008
1-4. del: Merilne naprave za merjenje
radijskih motenj in odpornosti – Pomožna
oprema – Sevane motnje
Zamenjati obstoječa sklicevanja na CISPR 11, CISPR 16-2-1:2003, CISPR 16-2-3, CISPR 16-4-2 in
CISPR 22 z naslednjimi novimi sklicevanji:
CISPR 11 (spr) 2009 Industrijska, znanstvena in medicinska EN 55011 2009
(ISM) radiofrekvenčna oprema –
Karakteristike občutljivosti za radijske
motnje – Mejne vrednosti in merilne
metode
1)
EN 55016-1-4 je nadomeščen z EN 55016-1-4:2010 s podlago v CISPR 16-1-4:2010 + popravek December 2010.
SIST EN 61000-6-4:2007/A1 : 2011
CISPR 16-2-1 2008 Specifikacija za merilne naprave in metode EN 55016-2-1 2009
za merjenje radijskih motenj in odpornosti –
2-1. del: Metode za merjenje radijskih
...
SLOVENSKI STANDARD
01-maj-2011
(OHNWURPDJQHWQD]GUXåOMLYRVW (0& GHO 2VQRYQL JHQHULþQL VWDQGDUGL
6WDQGDUGRGGDMDQMDPRWHQMYLQGXVWULMVNLKRNROMLK'RGDWHN$ ,(&
$
Electromagnetic compatibility (EMC) - Part 6-4: Generic standards - Emission standard
for industrial environments
Elektromagnetische Verträglichkeit (EMV) - Teil 6-4: Fachgrundnormen -
Störaussendung für Industriebereiche
Compatibilité électromagnétique (CEM) - Partie 6-4: Normes génériques - Norme sur
l'émission pour les environnements industriels
Ta slovenski standard je istoveten z: EN 61000-6-4:2007/A1:2011
ICS:
33.100.10 Emisija Emission
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN 61000-6-4/A1
NORME EUROPÉENNE
February 2011
EUROPÄISCHE NORM
ICS 33.100.10
English version
Electromagnetic compatibility (EMC) -
Part 6-4: Generic standards -
Emission standard for industrial environments
(IEC 61000-6-4:2006/A1:2010)
Compatibilité électromagnétique (CEM) - Elektromagnetische Verträglichkeit (EMV)
Partie 6-4: Normes génériques - -
Norme sur l'émission pour les Teil 6-4: Fachgrundnormen -
environnements industriels Störaussendung für Industriebereiche
(CEI 61000-6-4:2006/A1:2010) (IEC 61000-6-4:2006/A1:2010)
This amendment A1 modifies the European Standard EN 61000-6-4:2007; it was approved by CENELEC on
2011-01-12. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this amendment the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This amendment exists in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CENELEC member into its own language and notified to the
Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy,
Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia,
Spain, Sweden, Switzerland and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Management Centre: Avenue Marnix 17, B - 1000 Brussels
© 2011 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61000-6-4:2007/A1:2011 E
Foreword
The text of document CISPR/H/205/FDIS, future amendment 1 to IEC 61000-6-4:2006, prepared by
CISPR SC H, Limits for the protection of radio services, was submitted to the IEC-CENELEC parallel vote
and was approved by CENELEC as amendment A1 to EN 61000-6-4:2007 on 2011-01-01.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN and CENELEC shall not be held responsible for identifying any or all such patent
rights.
The following dates were fixed:
– latest date by which the amendment has to be
implemented at national level by publication of
(dop) 2011-10-01
an identical national standard or by endorsement
– latest date by which the national standards conflicting
(dow) 2014-01-01
with the amendment have to be withdrawn
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of amendment 1:2010 to the International Standard IEC 61000-6-4:2006 was approved by
CENELEC as an amendment to the European Standard without any modification.
__________
- 3 - EN 61000-6-4:2007/A1:2011
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year
Add the following new references to the existing list:
IEC 60050-161 - International Electrotechnical Vocabulary - -
(IEV) -
Chapter 161: Electromagnetic compatibility
IEC 61000-4-20 2010 Electromagnetic compatibility (EMC) - EN 61000-4-20 2010
Part 4-20: Testing and measurement
techniques - Emission and immunity testing in
transverse electromagnetic (TEM)
waveguides
CISPR 14-1 2005 Electromagnetic compatibility - Requirements EN 55014-1 2006
for household appliances, electric tools and
similar apparatus -
Part 1: Emission
CISPR 16-1-1 2010 Specification for radio disturbance and EN 55016-1-1 2010
immunity measuring apparatus and methods -
Part 1-1: Radio disturbance and immunity
measuring apparatus - Measuring apparatus
CISPR 16-1-4 2007 Specification for radio disturbance and EN 55016-1-4 2007
1)
+ A1 2007 immunity measuring apparatus and methods - + A1 2008
Part 1-4: Radio disturbance and immunity
measuring apparatus - Ancillary equipment -
Radiated disturbances
Replace the existing references to CISPR 11, CISPR 16-2-1:2003, CISPR 16-2-3, CISPR 16-4-2 and
CISPR 22 by the following new references:
CISPR 11 (mod) 2009 Industrial, scientific and medical equipment - EN 55011 2009
Radio-frequency disturbance characteristics -
Limits and methods of measurement
CISPR 16-2-1 2008 Specification for radio disturbance and EN 55016-2-1 2009
immunity measuring apparatus and methods -
Part 2-1: Methods of measurement of
disturbances and immunity - Conducted
disturbance measurements
1)
EN 55016-1-4 is superseded by EN 55016-1-4:2010, which is based on CISPR 16-1-4:2010 + corr. December 2010.
Publication Year Title EN/HD Year
2)
CISPR 16-2-3 2006 Specification for radio disturbance and EN 55016-2-3 2006
immunity measuring apparatus and methods -
Part 2-3: Methods of measurement of
disturbances and immunity - Radiated
disturbance measurements
CISPR 16-4-2 2003 Specification for radio disturbance and EN 55016-4-2 2004
immunity measuring apparatus and methods -
Part 4-2: Uncertainties, statistics and limit
modelling - Uncertainty in EMC
measurements
CISPR 22 (mod) 2008 Information technology equipment - Radio EN 55022 2010
disturbance characteristics - Limits and
methods of measurement
2)
EN 55016-2-3 is superseded by EN 55016-2-3:2010, which is based on CISPR 16-2-3:2010.
IEC 61000-6-4 ®
Edition 2.0 2010-12
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
INTERNATIONAL SPECIAL COMMITTEE ON RADIO INTERFERENCE
COMITÉ INTERNATIONAL SPÉCIAL DES PERTURBATIONS RADIOÉLECTRIQUES
AMENDMENT 1
AMENDEMENT 1
Electromagnetic compatibility (EMC) –
Part 6-4: Generic standards – Emission standard for industrial environments
Compatibilité électromagnétique (CEM) –
Partie 6-4: Normes génériques – Norme sur l'émission pour les environnements
industriels
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
L
CODE PRIX
ICS 33.100.10 ISBN 978-2-88912-253-0
– 2 – 61000-6-4 Amend. 1 Ó IEC:2010
FOREWORD
This amendment has been prepared by CISPR subcommittee H: Limits for the protection of
radio services.
The text of this amendment is based on the following documents:
FDIS Report on voting
CISPR/H/205/FDIS CISPR/H/209/RVD
Full information on the voting for the approval of this amendment can be found in the report
on voting indicated in the above table.
The committee has decided that the contents of this amendment and the base publication will
remain unchanged until the stability date indicated on the IEC web site under
"http://webstore.iec.ch" in the data related to the specific publication. At this date, the
publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
_____________
Contents
Replace the title of Clause 3 by the following new title:
3 Terms, definitions and abbreviations
Replace the title of Clause 8 by the following new title:
8 Measurement uncertainty
Replace the title of Clause 9 by the following new title:
9 Application of limits and tests for conformity of equipment in series production
Add the following new Clauses 10 and 11:
10 Compliance with this standard
11 Emission test requirements
Replace the title of Table 1 by the following new title:
Table 1 - Emission – Enclosure port
Add the following new Tables:
Table 2 - Emission – Low voltage AC mains port
61000-6-4 Amend. 1 Ó IEC:2010 – 3 –
Table 3 – Emission – Telecommunications/network port
2 Normative references
Add the following new references to the existing list:
IEC 60050-161, International Electrotechnical Vocabulary - Chapter 161: Electromagnetic
compatibility
IEC 61000-4-20:2010, Electromagnetic compatibility (EMC) – Part 4-20: Testing and
measurement techniques – Emission and immunity testing in transverse electromagnetic
(TEM) waveguide
CISPR 14-1:2005, Electromagnetic compatibility – Requirements for household appliances,
electric tools and similar apparatus – Part 1: Emission
Amendment 1:2008
CISPR 16-1-1:2010, Specification for radio disturbance and immunity measuring apparatus
and methods – Part 1-1: Radio disturbance and immunity measuring apparatus - Measuring
apparatus
CISPR 16-1-4:2007, Specification for radio disturbance and immunity measuring apparatus
and methods – Part 1-4: Radio disturbance and immunity measuring apparatus – Ancillary
equipment – Radiated disturbances
Amendment 1:2007
Replace the existing references to CISPR 11, CISPR 16-2-1:2003, CISPR 16-2-3, CISPR 16-
4-2 and CISPR 22, by the following new references:
CISPR 11:2009, Industrial, scientific and medical equipment – Radio-frequency disturbance
characteristics – Limits and methods of measurement
CISPR 16-2-1:2008, Specification for radio disturbance and immunity measuring apparatus
and methods – Part 2-1: Methods of measurement of disturbances and immunity – Conducted
disturbance measurements
CISPR 16-2-3:2006, Specification for radio disturbance and immunity measuring apparatus
and methods – Part 2-3: Methods of measurement of disturbances and immunity – Radiated
disturbance measurements
CISPR 16-4-2:2003, Specification for radio disturbance and immunity measuring apparatus
and methods – Part 4-2: Uncertainties, statistics and limit modelling – Uncertainty in EMC
measurements
CISPR 22:2008, Information technology equipment – Radio disturbance characteristics –
Limits and methods of measurement
3 Terms and definitions
Replace the title, first paragraph and Note of this clause by the following:
– 4 – 61000-6-4 Amend. 1 Ó IEC:2010
3 Terms, definitions and abbreviations
For the purposes of this document, the terms and definitions given in IEC 60050-161, as well
as the following apply.
Renumber the existing definitions 3.1, 3.2, 3.3, 3.4, 3.5, 3.6, 3.7 as 3.1.1, 3.1.2, 3.1.3, 3.1.4,
3.1.5, 3.1.6, 3.1.7 respec
...
SIST EN 61000-6-4:2007/A1:2011 표준은 산업 환경에서 사용할 전기 및 전자 장비의 전자기 적합성(EMC) 방출 요구 사항을 규정하고 있습니다. 이 표준의 범위는 0 Hz에서 400 GHz까지의 주파수 범위를 포함하며, 특정 요구 사항이 명시되지 않은 주파수에서는 측정을 수행할 필요가 없습니다. 이_GENERIC EMC 방출 표준은 관련 전용 제품이나 제품군에 대한 EMC 방출 표준이 존재하지 않을 때 적용됩니다. 이 표준은 고압 또는 중압 변압기로 공급되는 전력 네트워크에 연결될 전장치에 적용되며, 제조업체나 유사한 시설에서 운영되는 산업 위치에서 사용할 수 있도록 설계되었습니다. 산업 위치는 실내 및 실외 모두를 포함하며, 특히 산업, 과학 및 의료(ISM) 장비, 자주 전환되는 대전도성 또는 정전용량 부하, 높은 전류와 관련된 자기장과 같은 여러 특성을 가진 장소를 포함합니다. SIST EN 61000-6-4:2007/A1:2011 표준의 주요 목적은 지속적이고 일시적인 전도 및 방사 간섭과 관련하여 정의된 장비에 대한 방출 시험 요구 사항을 제시하는 것입니다. 방출 요구 사항은 산업 위치에서 정상적으로 작동하는 장비가 발생하는 간섭이 다른 장비의 정상 작동을 방해하지 않는 수준으로 유지되도록 선택되었습니다. 이는 공장 혹은 비슷한 산업 시설에서 사용할 장비에 대한 필수적인 EMC 방출 요구 사항을 나타냅니다. 이 표준은 실용적인 측면에서 모든 간섭 현상이 시험 목적에 포함되지 않고, 해당 표준이 다루는 장비에 관련된 현상만을 고려하고 있습니다. 따라서, SIST EN 61000-6-4:2007/A1:2011은 산업 환경에서 반드시 필요하고 의미 있는 EMC 방출 기준으로서의 역할을 다하고 있습니다.
The SIST EN 61000-6-4:2007/A1:2011 standard provides critical guidelines regarding electromagnetic compatibility (EMC) in industrial environments, specifically addressing emission standards for electrical and electronic apparatus. The standard's scope is robust, covering apparatus intended for industrial applications, which includes those connected to high or medium voltage power networks and battery-operated devices designed for use in industrial settings. One of the significant strengths of this standard is its coverage of emission requirements over a broad frequency range of 0 Hz to 400 GHz, ensuring comprehensive protection against potential EMC issues. The standard wisely exempts measurement at frequencies where no requirements are specified, streamlining the testing process. This pragmatic approach not only enhances the practicality but also ensures that resources are allocated efficiently to relevant emissions testing. The standard is particularly relevant in the context of industrial environments characterized by the presence of heavy inductive or capacitive loads, high currents, and corresponding magnetic fields. By defining the emission test requirements, it ensures that disturbances generated by equipment operating under normal conditions do not interfere with the operation of other devices, thereby promoting operational integrity within industrial settings. This proactive measure contributes significantly to maintaining a stable and efficient manufacturing environment. Furthermore, the emphasis on continuous and transient, conducted and radiated disturbances highlights the standard’s comprehensive nature in addressing various emission scenarios relevant to industrial equipment. Though fault conditions are not considered, the selective focus on significant disturbance phenomena ensures that the EMC emission standards are both relevant and applicable to the equipment covered. In summary, the SIST EN 61000-6-4:2007/A1:2011 standard stands out for its thorough approach to defining essential EMC emission requirements for industrial environments, making it an invaluable resource for manufacturers and stakeholders in the field of electromagnetic compatibility.
La norme SIST EN 61000-6-4:2007/A1:2011 constitue un élément fondamental pour assurer la compatibilité électromagnétique (CEM) dans les environnements industriels. Son champ d'application est clairement défini, s'appliquant aux appareils électriques et électroniques destinés à être utilisés dans des environnements industriels, allant des installations de production à d'autres sites similaires. Cette norme couvre des exigences d'émission allant de 0 Hz à 400 GHz, ce qui garantit une large couverture des fréquences pertinentes pour les dispositifs utilisés dans ces environnements. Parmi les forces majeures de cette norme, on note la spécificité des exigences relatives aux émissions en fonction des environnements, qu'ils soient intérieurs ou extérieurs. Le standard se démarque également par sa capacité à inclure des équipements alimentés par batterie, élargissant ainsi son application à une variété d'appareils utilisés dans des contextes industriels variés. En définissant les exigences d'émission pour les perturbations conduites et rayonnées, la norme assure que les appareils ne provoquent pas de désruptions à d'autres équipements, une considération cruciale dans un environnement de production où le bon fonctionnement est primordial. La pertinence de cette norme réside dans sa capacité à harmoniser les exigences d'émission dans des environnements où les charges inductives et capacitives élevées sont courantes. En ciblant les perturbations considérées comme significatives pour les équipements, la norme garantit que les tests réalisés reflètent fidèlement les conditions réelles d'utilisation. Grâce à toutes ces caractéristiques, la SIST EN 61000-6-4:2007/A1:2011 représente une avancée essentielle pour la gestion de la compatibilité électromagnétique dans l'industrie, promouvant ainsi un fonctionnement fiable et efficace des appareils dans des contextes variés.
SIST EN 61000-6-4:2007/A1:2011の標準は、産業環境における電磁干渉（EMC）の発生基準を定めており、対象となる機器が産業用環境で使用されることを前提としています。この標準は、0 Hzから400 GHzの周波数範囲での発生要件を網羅しており、特に産業における電子機器や電気装置に対する一般的なEMC発生標準としての重要性を持っています。 この標準の大きな強みは、産業環境におけるさまざまな発生要件に関連する試験要件を明確に定義している点です。特に、通常の運用条件下において、発生する干渉が他の機器の正常な動作を妨げないレベルに抑えられるように設計されています。また、特定の製品や製品ファミリーに対する専用のEMC発生標準が存在しない場合にも適用されるため、多様な産業用機器に広く利用可能です。 加えて、標準は、蓄電池駆動の機器や高・中電圧トランスからの電源が供給される装置にも適用され、産業用の使用条件を考慮に入れた幅広い適用範囲を持っています。産業環境には、屋内外を問わず、多くの重負荷や高電流に伴う磁場が存在するため、これらの要素を考慮した発生要件の設定がなされています。 本標準では、連続的および過渡的、伝導性および放射性の干渉に対する試験要件が示されており、試験対象の機器にとって関連性の高い干渉現象に限定して評価されている点も、標準の信頼性を高める要因となっています。全体として、SIST EN 61000-6-4:2007/A1:2011は、産業環境における電磁適合性に関する重要な基準を提供しており、その適用性や具体的な発生要件の明確さは、業界にとって非常に価値の高いものとなっています。
Die Norm SIST EN 61000-6-4:2007/A1:2011 befasst sich mit den elektromagnetischen Verträglichkeitsanforderungen (EMC) in industriellen Umgebungen und stellt einen entscheidenden Leitfaden für die Emission von elektrischen und elektronischen Geräten dar, die in solchen Kontexten eingesetzt werden. Der Anwendungsbereich dieser Norm erstreckt sich auf Frequenzen von 0 Hz bis 400 GHz, wobei sie spezifische Emissionsanforderungen definiert, die in industriellen Umgebungen gelten. Ein wesentlicher Stärke dieser Norm ist ihre generische Natur, die anwendbar ist, wenn keine spezifischen Regelungen für ein bestimmtes Produkt oder eine Produktfamilie existieren. Dies ermöglicht eine breit gefächerte Anwendung in verschiedenen industriellen Szenarien, einschließlich sowohl fest installierter Geräte als auch batteriebetriebener Apparate, die in der Nähe von industriellen Standorten eingesetzt werden. Die Norm ist besonders relevant für Einrichtungen, die von Hoch- oder Mittelspannungsumspannwerken versorgt werden und in Bereichen mit schweren inductiven oder capacitive Lasten oder hohen Strömen arbeiten. Die Norm definiert die Anforderungen an Emissionstests für die betreffenden Geräte hinsichtlich kontinuierlicher und transienter Störungen sowie geleiteter und ausgestrahlter Störungen. Durch die Festlegung dieser Emissionserfordernisse wird sichergestellt, dass die von den Geräten erzeugten Störungen ein Maß nicht überschreiten, das den Betrieb anderer Geräte beeinträchtigen könnte. Dies ist besonders wichtig in Industrieumgebungen, wo der reibungslose Betrieb von Maschinen entscheidend für die Produktion ist. Obwohl nicht alle Störphänomene in diese Norm aufgenommen wurden, konzentriert sie sich auf die für die abgedeckten Geräte als relevant erachteten Störungen, was die Effektivität und Anwendbarkeit der Norm in der Praxis erhöht. Ingesamt bieten die in der SIST EN 61000-6-4:2007/A1:2011 festgelegten Emissionsanforderungen einen klaren und notwendigen Rahmen, um die elektromagnetische Verträglichkeit in industriellen Umgebungen zu gewährleisten und die sichere Nutzung von elektrischen und elektronischen Apparaturen zu fördern.
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...