Fixed capacitors for use in electronic equipment -- Part 9: Sectional specification: Fixed capacitors of ceramic dielectric, Class 2

This part of IEC 60384 is applicable to fixed capacitors of ceramic dielectric with a defined temperature coefficient (dielectric Class 2), intended for use in electronic equipment, including leadless capacitors but excluding fixed surface mount multilayer capacitors of ceramic dielectric, which are covered by IEC 60384-22 (Class 2).
Capacitors for electromagnetic interference suppression are not included, but are covered by IEC 60384-14.

Festkondensatoren zur Verwendung in Geräten der Elektronik - Teil 9: Rahmenspezifikation – Keramik-Festkondensatoren, Klasse 2

Condensateurs fixes utilisés dans les équipements électroniques - Partie 9: Spécification intermédiaire: Condensateurs fixes à diélectrique en céramique, Classe 2

L'IEC 60384-9:2015 est applicable aux condensateurs fixes en céramique diélectrique avec un coefficient de température défini (diélectrique de Classe 2), destinés à être utilisés dans des équipements électroniques, y compris les condensateurs sans plomb et à l'exclusion des condensateurs multicouches montés en surface fixe en céramique diélectrique. Cette quatrième édition annule et remplace la troisième édition parue en 2005. Cette quatrième édition est le résultat des activités de maintenance relatives à l'édition précédente. Toutes les modifications acceptées peuvent être classées comme des révisions mineures.

Pritrjeni kondenzatorji za uporabo v elektronski opremi - 9. del: Področna specifikacija: pritrjeni kondenzatorji s keramičnim dielektrikom, razred 2

Ta del standarda IEC 60384 velja za pritrjene kondenzatorje s keramičnim dielektrikom z določenim temperaturnim koeficientom (dielektrik razreda 2), namenjene uporabi v elektronski opremi, vključno s kondenzatorji brez svinca, ne velja pa za pritrjene večplastne kondenzatorje za površinsko namestitev s keramičnim dielektrikom, ki so zajeti v standardu IEC 60384-22 (razred 2).
Kondenzatorji za preprečevanje elektromagnetnih motenj niso vključeni, vendar so zajeti v standardu IEC 60384-14.

General Information

Status
Published
Publication Date
13-Aug-2015
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
15-Jun-2015
Due Date
20-Aug-2015
Completion Date
14-Aug-2015

RELATIONS

Buy Standard

Standard
SIST EN 60384-9:2015
English language
38 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
SIST EN 60384-9:2015
01-september-2015
1DGRPHãþD
SIST EN 60384-9:2005
3ULWUMHQLNRQGHQ]DWRUML]DXSRUDERYHOHNWURQVNLRSUHPLGHO3RGURþQD
VSHFLILNDFLMDSULWUMHQLNRQGHQ]DWRUMLVNHUDPLþQLPGLHOHNWULNRPUD]UHG

Fixed capacitors for use in electronic equipment -- Part 9: Sectional specification: Fixed

capacitors of ceramic dielectric, Class 2
Festkondensatoren zur Verwendung in Geräten der Elektronik - Teil 9:
Rahmenspezifikation – Keramik-Festkondensatoren, Klasse 2

Condensateurs fixes utilisés dans les équipements électroniques - Partie 9: Spécification

intermédiaire: Condensateurs fixes à diélectrique en céramique, Classe 2
Ta slovenski standard je istoveten z: EN 60384-9:2015
ICS:
31.060.10 Fiksni kondenzatorji Fixed capacitors
SIST EN 60384-9:2015 en

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 60384-9:2015
---------------------- Page: 2 ----------------------
SIST EN 60384-9:2015
EUROPEAN STANDARD EN 60384-9
NORME EUROPÉENNE
EUROPÄISCHE NORM
May 2015
ICS 31.060.20 Supersedes EN 60384-9:2005
English Version
Fixed capacitors for use in electronic equipment - Part 9:
Sectional specification: Fixed capacitors of ceramic dielectric,
Class 2
(IEC 60384-9:2015)

Condensateurs fixes utilisés dans les équipements Festkondensatoren zur Verwendung in Geräten der

électroniques - Partie 9: Spécification intermédiaire: Elektronik - Teil 9: Rahmenspezifikation - Keramik-

Condensateurs fixes à diélectrique en céramique, Classe 2 Festkondensatoren, Klasse 2

(IEC 60384-9:2015) (IEC 60384-9:2015)

This European Standard was approved by CENELEC on 2015-04-14. CENELEC members are bound to comply with the CEN/CENELEC

Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC

Management Centre or to any CENELEC member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation

under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the

same status as the official versions.

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,

Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,

Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,

Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels

© 2015 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.

Ref. No. EN 60384-9:2015 E
---------------------- Page: 3 ----------------------
SIST EN 60384-9:2015
EN 60384-9:2015 - 2 -
Foreword

The text of document 40/2339/FDIS, future edition 4 of IEC 60384-9, prepared by IEC TC 40, "Capacitors

and resistors for electronic equipment" was submitted to the IEC-CENELEC parallel vote and was

approved by CENELEC as EN 60384-9:2015.
The following dates are fixed:
(dop) 2016-01-14
• latest date by which the document has
to be implemented at national level by
publication of an identical national
standard or by endorsement
(dow) 2018-04-14
• latest date by which the national
standards conflicting with the
document have to be withdrawn
This document supersedes EN 60384-9:2005.

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent

rights.
Endorsement notice

The text of the International Standard IEC 60384-9:2015 was approved by CENELEC as a European

Standard without any modification.

In the official version, for Bibliography, the following notes have to be added for the standards indicated:

IEC 60384-14 NOTE Harmonized as EN 60384-14.
IEC 60384-22 NOTE Harmonized as EN 60384-22.
---------------------- Page: 4 ----------------------
SIST EN 60384-9:2015
- 3 - EN 60384-9:2015
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following documents, in whole or in part, are normatively referenced in this document and are

indispensable for its application. For dated references, only the edition cited applies. For undated

references, the latest edition of the referenced document (including any amendments) applies.

NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant EN/HD

applies.

NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:

www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60063 1963 Preferred number series for resistors and - -
capacitors
+A1 1967 - -
+A2 1977 - -
IEC 60068-1 2013 Environmental testing -- Part 1: General and EN 60068-1 2014
guidance
IEC 60384-1 2008 Fixed capacitors for use in electronic EN 60384-1 2009
equipment -- Part 1: Generic specification
IEC 61193-2 2007 Quality assessment systems -- Part 2: EN 61193-2 2007
Selection and use of sampling plans for
inspection of electronic components and
packages
ISO 3 1973 Preferred numbers; Series of preferred - -
numbers
---------------------- Page: 5 ----------------------
SIST EN 60384-9:2015
---------------------- Page: 6 ----------------------
SIST EN 60384-9:2015
IEC 60384-9
Edition 4.0 2015-03
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Fixed capacitors for use in electronic equipment –
Part 9: Sectional specification: Fixed capacitors of ceramic dielectric, Class 2
Condensateurs fixes utilisés dans les équipements électroniques –
Partie 9: Spécification intermédiaire: Condensateurs fixes à diélectrique en
céramique, Classe 2
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 31.060.20 ISBN 978-2-8322-2284-3

Warning! Make sure that you obtained this publication from an authorized distributor.

Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.

® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 7 ----------------------
SIST EN 60384-9:2015
– 2 – IEC 60384-9:2015 © IEC 2015
CONTENTS

FOREWORD ........................................................................................................................... 5

1 General ........................................................................................................................... 7

1.1 Scope ..................................................................................................................... 7

1.2 Object ..................................................................................................................... 7

1.3 Normative references .............................................................................................. 7

1.4 Information to be given in a detail specification ....................................................... 7

1.4.1 General ........................................................................................................... 7

1.4.2 Outline drawing and dimensions ...................................................................... 8

1.4.3 Mounting ......................................................................................................... 8

1.4.4 Ratings and characteristics .............................................................................. 8

1.4.5 Marking ........................................................................................................... 9

1.5 Terms and definitions .............................................................................................. 9

1.6 Marking ................................................................................................................... 9

1.6.1 General ........................................................................................................... 9

1.6.2 Marking on the body ...................................................................................... 10

1.6.3 Marking of the packaging ............................................................................... 10

1.6.4 Additional marking ......................................................................................... 10

2 Preferred ratings and characteristics ............................................................................. 10

2.1 Preferred characteristics ....................................................................................... 10

2.2 Preferred values of ratings .................................................................................... 10

2.2.1 Rated temperature ......................................................................................... 10

2.2.2 Rated voltage (U ) ........................................................................................ 10

2.2.3 Category voltage (U ) ................................................................................... 11

2.2.4 Preferred values of nominal capacitance and associated tolerance

values ............................................................................................................ 11

2.2.5 Temperature characteristic of capacitance ..................................................... 11

3 Quality assessment procedures ..................................................................................... 12

3.1 Primary stage of manufacture ............................................................................... 12

3.2 Structurally similar components ............................................................................ 12

3.3 Certified test records of released lots .................................................................... 12

3.4 Qualification approval ........................................................................................... 12

3.4.1 General ......................................................................................................... 12

3.4.2 Qualification approval on the basis of the fixed sample size procedure .......... 12

3.4.3 Tests ............................................................................................................. 13

3.5 Quality conformance inspection ............................................................................ 18

3.5.1 Formation of inspection lots ........................................................................... 18

3.5.2 Test schedule ................................................................................................ 19

3.5.3 Delayed delivery ............................................................................................ 19

3.5.4 Assessment levels ......................................................................................... 19

4 Test and measurement procedures ................................................................................ 20

4.1 General ................................................................................................................. 20

4.2 Special preconditioning ......................................................................................... 20

4.3 Visual examination and check of dimensions ........................................................ 20

4.4 Electrical tests ...................................................................................................... 20

4.4.1 Capacitance .................................................................................................. 20

4.4.2 Tangent of loss angle (tan δ) ......................................................................... 21

---------------------- Page: 8 ----------------------
SIST EN 60384-9:2015
IEC 60384-9:2015 © IEC 2015 – 3 –

4.4.3 Insulation resistance (R ) ............................................................................... 21

4.4.4 Voltage proof ................................................................................................. 22

4.5 Temperature characteristic of capacitance ............................................................ 23

4.5.1 Special preconditioning .................................................................................. 23

4.5.2 Measuring conditions ..................................................................................... 23

4.5.3 Requirements ................................................................................................ 23

4.6 Robustness of terminations ................................................................................... 23

4.7 Resistance to soldering heat ................................................................................. 23

4.7.1 General ......................................................................................................... 23

4.7.2 Special preconditioning .................................................................................. 24

4.7.3 Initial measurement ....................................................................................... 24

4.7.4 Recovery ....................................................................................................... 24

4.7.5 Final inspection, measurements and requirements......................................... 24

4.8 Solderability .......................................................................................................... 24

4.8.1 General ......................................................................................................... 24

4.8.2 Test conditions .............................................................................................. 24

4.8.3 Final inspection, measurements and requirements......................................... 24

4.9 Rapid change of temperature (if required) ............................................................. 24

4.9.1 General ......................................................................................................... 24

4.9.2 Special preconditioning .................................................................................. 24

4.9.3 Initial measurement ....................................................................................... 25

4.9.4 Test conditions .............................................................................................. 25

4.9.5 Recovery ....................................................................................................... 25

4.10 Vibration ............................................................................................................... 25

4.10.1 General ......................................................................................................... 25

4.10.2 Test conditions .............................................................................................. 25

4.10.3 Final inspection, measurements and requirements......................................... 25

4.11 Bump (repetitive shock) ........................................................................................ 25

4.11.1 General ......................................................................................................... 25

4.11.2 Initial measurements ..................................................................................... 25

4.11.3 Test conditions .............................................................................................. 25

4.11.4 Final inspection, measurements and requirements......................................... 26

4.12 Shock (non-repetitive shock) ................................................................................. 26

4.12.1 General ......................................................................................................... 26

4.12.2 Initial measurements ..................................................................................... 26

4.12.3 Test conditions .............................................................................................. 26

4.12.4 Final inspection, measurements and requirements......................................... 26

4.13 Climatic sequence................................................................................................. 27

4.13.1 General ......................................................................................................... 27

4.13.2 Special preconditioning .................................................................................. 27

4.13.3 Initial measurements ..................................................................................... 27

4.13.4 Dry heat ........................................................................................................ 27

4.13.5 Damp heat, cyclic, Test Db, first cycle ........................................................... 27

4.13.6 Cold............................................................................................................... 27

4.13.7 Low air pressure ............................................................................................ 27

4.13.8 Damp heat, cyclic, Test Db, remaining cycles ................................................ 28

4.14 Damp heat, steady state ....................................................................................... 28

4.14.1 General ......................................................................................................... 28

4.14.2 Special preconditioning .................................................................................. 28

---------------------- Page: 9 ----------------------
SIST EN 60384-9:2015
– 4 – IEC 60384-9:2015 © IEC 2015

4.14.3 Initial measurement ....................................................................................... 29

4.14.4 Test conditions .............................................................................................. 29

4.14.5 Recovery ....................................................................................................... 29

4.14.6 Final inspection, measurements and requirements......................................... 29

4.15 Endurance ............................................................................................................ 30

4.15.1 General ......................................................................................................... 30

4.15.2 Special preconditioning .................................................................................. 30

4.15.3 Initial measurement ....................................................................................... 30

4.15.4 Test conditions .............................................................................................. 30

4.15.5 Recovery ....................................................................................................... 30

4.15.6 Final inspection, measurements and requirements......................................... 30

4.16 Component solvent resistance (if applicable) ........................................................ 31

4.17 Solvent resistance of the marking (if applicable) ................................................... 31

Annex A (informative) Capacitance ageing of fixed capacitors of ceramic dielectric,

Class 2 .......................................................................................................................... 32

A.1 General ................................................................................................................. 32

A.2 Law of capacitance ageing .................................................................................... 32

A.3 Capacitance measurements and capacitance tolerance (see 4.4.1)....................... 33

A.4 Special preconditioning (see 4.2) .......................................................................... 33

Bibliography .......................................................................................................................... 35

Table 1 – Preferred tolerance on nominal capacitance .......................................................... 11

Table 2 – Preferred values of temperature characteristics ..................................................... 11

Table 3 – Sampling plan together with numbers of permissible non-conforming items

for qualification approval tests, assessment level EZ ............................................................ 14

Table 4 – Test schedule for qualification approval ................................................................ 15

Table 5 – Lot-by-lot inspection .............................................................................................. 19

Table 6 – Periodic tests ........................................................................................................ 20

Table 7 – Measuring conditions ............................................................................................ 21

Table 8 – Insulation resistance requirements ........................................................................ 22

Table 9 – Test voltages ......................................................................................................... 22

Table 10 – Details of measuring conditions ........................................................................... 23

Table 11 – Maximum capacitance change ............................................................................. 24

Table 12 – Preferred severities (of non-repetitive shock) ...................................................... 26

Table 13 – Maximum capacitance change ............................................................................. 27

Table 14 – Number of damp heat cycles ............................................................................... 28

Table 15 – Final inspection measurements and requirements ............................................... 28

Table 16 – Test conditions for damp heat, steady state ......................................................... 29

Table 17 – Final inspection, measurements and requirements .............................................. 29

Table 18 – Endurance test conditions ................................................................................... 30

Table 19 – Final inspection, measurements and requirements .............................................. 30

---------------------- Page: 10 ----------------------
SIST EN 60384-9:2015
IEC 60384-9:2015 © IEC 2015 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT –
Part 9: Sectional specification:
Fixed capacitors of ceramic dielectric, Class 2
FOREWORD

1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising

all national electrotechnical committees (IEC National Committees). The object of IEC is to promote

international co-operation on all questions concerning standardization in the electrical and electronic fields. To

this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,

Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC

Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested

in the subject dealt with may participate in this preparatory work. International, governmental and non-

governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely

with the International Organization for Standardization (ISO) in accordance with conditions determined by

agreement between the two organizations.

2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international

consensus of opinion on the relevant subjects since each technical committee has representation from all

interested IEC National Committees.

3) IEC Publications have the form of recommendations for international use and are accepted by IEC National

Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC

Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any

misinterpretation by any end user.

4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications

transparently to the maximum extent possible in their national and regional publications. Any divergence

between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in

the latter.

5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity

assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any

services carried out by independent certification bodies.

6) All users should ensure that they have the latest edition of this publication.

7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and

members of its technical committees and IEC National Committees for any personal injury, property damage or

other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and

expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC

Publications.

8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is

indispensable for the correct application of this publication.

9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of

patent rights. IEC shall not be held responsible for identifying any or all such patent rights.

International Standard IEC 60384-9 has been prepared by IEC technical committee 40:

Capacitors and resistors for electronic equipment.

This fourth edition cancels and replaces the third edition published in 2005. This fourth edition

is a result of maintenance activities related to the previous edition. All changes that have

been agreed upon can be categorized as minor revisions.
The text of this standard is based on the following documents:
FDIS Report on voting
40/2339/FDIS 40/2364/RVD

Full information on the voting for the approval of this standard can be found in the report on

voting indicated in the above table.
---------------------- Page: 11 ----------------------
SIST EN 60384-9:2015
– 6 – IEC 60384-9:2015 © IEC 2015

This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.

A list of all parts in the IEC 60384 series, published under the general title Fixed capacitors

for use in electronic equipment, can be found on the IEC website.

The committee has decided that the contents of this publication will remain unchanged until

the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the data

related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
---------------------- Page: 12 ----------------------
SIST EN 60384-9:2015
IEC 60384-9:2015 © IEC 2015 – 7 –
FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT –
Part 9: Sectional specification:
Fixed capacitors of ceramic dielectric, Class 2
1 General
1.1 Scope

This part of IEC 60384 is applicable to fixed capacitors of ceramic dielectric with a defined

temperature coefficient (dielectric Class 2), intended for use in electronic equipment, including

leadless capacitors but excluding fixed surface mount multilayer capacitors of ceramic

dielectric, which are covered by IEC 60384-22 (Class 2).

Capacitors for electromagnetic interference suppression are not included, but are covered by

IEC 60384-14.
1.2 Object

The object of this standard is to prescribe preferred ratings and characteristics and to select

from IEC 60384-1:2008 the appropriate quality assessment procedures, tests and measuring

methods and to give general performance requirements for this type of capacitor. Test

severities and requirements prescribed in detail specifications referring to this sectional

specification shall be of equal or higher performance level because lower performance levels

are not permitted.
1.3 Normative references

The following documents, in whole or in part, are normatively referenced in this document and

are indispensable for its application. For dated references, only the edition cited applies. For

undated references, the latest edition of the referenced document (including any
amendments) applies.
IEC 60063:1963, Preferred number series for resistors and capacitors
IEC 60063:1963/AMD1:1967
IEC 60063:1963/AM
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.