SIST EN 12100:2025
(Main)Plastics piping systems - Polyethylene (PE) valves - Test method for resistance to bending between supports
Plastics piping systems - Polyethylene (PE) valves - Test method for resistance to bending between supports
This document specifies a test method for the resistance to bending of a test piece, made of a valve assembled together with two pipes and placed between supports, when subjected to internal pressure.
This document is applicable to valves with a polyethylene (PE) body for use with pipes having a nominal outside diameter from greater than 63 mm up to and including 400 mm and intended for the transport of fluids.
When specified in the product standard, this document can be applied to valves of material different than PE.
Kunststoff-Rohrleitungssysteme - Armaturen aus Polyethylen (PE) - Prüfverfahren für den Widerstand gegen Biegen bei Dreipunktbelastung
Dieses Dokument legt ein Prüfverfahren für die Biegefestigkeit eines Prüfkörpers fest, der aus einer mit zwei Rohren zusammengebauten Armatur besteht und zwischen Auflagern angeordnet ist, wenn er einem Innendruck ausgesetzt wird.
Dieses Dokument ist anwendbar für Armaturen mit einem Gehäuse aus Polyethylen (PE) für den Einsatz mit Rohren mit einem Nenn-Außendurchmesser größer als 63 mm bis einschließlich 400 mm, die für den Transport von Flüssigkeiten vorgesehen sind.
Wenn in der Produktnorm festgelegt, kann dieses Dokument auf Armaturen aus einem anderen Werkstoff als PE angewendet werden.
Systemes de canalisations en plastiques - Robinets en polyéthylene (PE) - Méthode d'essai de résistance a la flexion entre supports
Le présent document spécifie une méthode d'essai relative à la résistance à la flexion d’une éprouvette, constituée d’un robinet assemblé à deux tubes et placée entre des supports, lorsqu’elle est soumise à une pression interne.
Le présent document s'applique aux robinets avec un corps en polyéthylène (PE), utilisés avec des tubes présentant un diamètre extérieur nominal supérieur à 63 mm et inférieur ou égal à 400 mm, destinés au transport de fluides.
Lorsque cela est spécifié dans la norme de produit, le présent document peut être appliqué à des robinets en matériau autre que le PE.
Cevni sistemi iz polimernih materialov - Ventili iz polietilena (PE) - Metoda za preskus odpornosti proti upogibanju med podporami
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-junij-2025
Cevni sistemi iz polimernih materialov - Ventili iz polietilena (PE) - Metoda za
preskus odpornosti proti upogibanju med podporami
Plastics piping systems - Polyethylene (PE) valves - Test method for resistance to
bending between supports
Kunststoff-Rohrleitungssysteme - Armaturen aus Polyethylen (PE) - Prüfverfahren für
den Widerstand gegen Biegen bei Dreipunktbelastung
Systemes de canalisations en plastiques - Robinets en polyéthylene (PE) - Méthode
d'essai de résistance a la flexion entre supports
Ta slovenski standard je istoveten z: EN 12100:2025
ICS:
23.040.01 Deli cevovodov in cevovodi Pipeline components and
na splošno pipelines in general
83.140.30 Polimerne cevi in fitingi za Plastics pipes and fittings for
snovi, ki niso tekočine non fluid use
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN 12100
EUROPEAN STANDARD
NORME EUROPÉENNE
March 2025
EUROPÄISCHE NORM
ICS 23.040.01 Supersedes EN 12100:1997
English Version
Plastics piping systems - Polyethylene (PE) valves - Test
method for resistance to bending between supports
Systèmes de canalisations en plastiques - Robinets en Kunststoff-Rohrleitungssysteme - Armaturen aus
polyéthylène (PE) - Méthode d'essai de résistance à la Polyethylen (PE) - Prüfverfahren für die Biegefestigkeit
flexion entre supports zwischen Auflagern
This European Standard was approved by CEN on 27 January 2025.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2025 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12100:2025 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
Introduction . 4
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 Principle. 5
5 Apparatus . 6
5.1 Static uniaxial testing machine . 6
5.2 Torque measuring device . 6
5.3 Compressed air supply . 6
5.4 Pressure . 6
5.5 Airtight piping systems . 6
6 Test pieces . 7
6.1 Sampling . 7
6.2 Preparation . 7
6.3 Number of test pieces . 7
7 Arrangements . 7
8 Test procedure . 8
9 Test report . 9
Bibliography .10
European foreword
This document (EN 12100:2025) has been prepared by Technical Committee CEN/TC 155“Plastics
piping systems and ducting systems”, the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2025, and conflicting national standards shall
be withdrawn at the latest by September 2025.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 12100:1997.
— the possibility to apply this test method to materials other than PE has been included in the Scope;
— in Clause 8, the test procedure has been revised.
Any feedback and questions on this document should be directed to the users’ national standards body.
A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of North
Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the United
Kingdom.
Introduction
This document specifies the requirements for the test method for resistance to bending between supports
of a valve made from polyethylene (PE) and which is intended to be used in pipelines for the transport of
fluids.
1 Scope
This document specifies a test method for the resistance to bending of a test piece, made of a valve
assembled together with two pipes and placed between supports, when subjected to internal pressure.
This document is applicable to valves with a polyethylene (PE) body for use with pipes having a nominal
outside diameter from greater than 63 mm up to and including 400 mm and intended for the transport
of fluids.
When specified in the product standard, this document can be applied to valves of material different than
PE.
2 Nor
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.