SIST EN ISO 10644:2001

Screw and washer assemblies with plain washers - Washer hardness classes 200 HV and 300 HV (ISO 10644:1998)

Kombi-Schrauben mit flachen Scheiben - Härteklassen der Scheiben 200 HV und 300 HV (ISO 10644:1998)

Diese Internationale Norm legt die Eigenscaften von metrischen Kombi-Schrauben mit flachen Scheiben mit Gewinde von M2 bis M12, mit flach aufliegenden Köpfen, mit Festigkeitsklassen bis einschließlich 10.9 und Scheiben der Härteklassen 200 HV und 300 HV fest. Die Scheiben sind unverlierbar und können sich frei drehen.

Vis a rondelle plate incorporée - Rondelles de classes de dureté 200 HV et 300 HV (ISO 10644:1998)

Vijaki z ujeto okroglo ravno podložko trdote 200 HV in 300 HV (ISO 10644:1998)

General Information

• Status: Withdrawn
• Publication Date: 30-Jun-2001
• Withdrawal Date: 23-Nov-2011
• ICS: 21.060.10 - Bolts, screws, studs
• ICS: 21.060.30 - Washers, locking elements
• Technical Committee: ISEL - Mechanical elements
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 24-Nov-2011
• Due Date: 17-Dec-2011
• Completion Date: 24-Nov-2011
• Ref Project: EN ISO 10644:1998 - Screw and washer assemblies with plain washers - Washer hardness classes 200 HV and 300 HV (ISO 10644:1998)

Relations

• Replaced By: SIST EN ISO 10644:2012 - Screw and washer assemblies made of steel with plain washers - Washer hardness classes 200 HV and 300 HV (ISO 10644:2009)
• Effective Date: 01-Jan-2012
• Replaced By: SIST EN ISO 10644:2012 - Screw and washer assemblies made of steel with plain washers - Washer hardness classes 200 HV and 300 HV (ISO 10644:2009)
• Effective Date: 08-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 10644:2001
01-julij-2001
Vijaki z ujeto okroglo ravno podložko trdote 200 HV in 300 HV (ISO 10644:1998)
Screw and washer assemblies with plain washers - Washer hardness classes 200 HV
and 300 HV (ISO 10644:1998)
Kombi-Schrauben mit flachen Scheiben - Härteklassen der Scheiben 200 HV und 300
HV (ISO 10644:1998)
Vis a rondelle plate incorporée - Rondelles de classes de dureté 200 HV et 300 HV (ISO
10644:1998)
Ta slovenski standard je istoveten z: EN ISO 10644:1998
ICS:
21.060.10 Sorniki, vijaki, stebelni vijaki Bolts, screws, studs
21.060.30 Podložke, varovalni elementi Washers, locking elements
SIST EN ISO 10644:2001 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 10644:2001

---------------------- Page: 2 ----------------------

SIST EN ISO 10644:2001

---------------------- Page: 3 ----------------------

SIST EN ISO 10644:2001

---------------------- Page: 4 ----------------------

SIST EN ISO 10644:2001

---------------------- Page: 5 ----------------------

SIST EN ISO 10644:2001

---------------------- Page: 6 ----------------------

SIST EN ISO 10644:2001
INTERNATIONAL ISO
STANDARD 10644
First edition
1998-08-01
Screw and washer assemblies with plain
washers — Washer hardness classes
200 HV and 300 HV
Vis à rondelle plate incorporée — Rondelles de classes de dureté 200 HV
et 300 HV
A
Reference number
ISO 10644:1998(E)

---------------------- Page: 7 ----------------------

SIST EN ISO 10644:2001
ISO 10644:1998(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide
federation of national standards bodies (ISO member bodies). The work of
preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which
a technical committee has been established has the right to be represented
on that committee. International organizations, governmental and non-
governmental, in liaison with ISO, also take part in the work. ISO
collaborates closely with the International Electrotechnical Commission
(IEC) on all matters of electrotechnical standardization.
Draft International Standards adopted by the technical committees are
circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting
a vote.
International Standard ISO 10644 was prepared by Technical Committee
ISO/TC 2, Fasteners.
Annex A of this International Standard is for information only.
©  ISO 1998
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced
or utilized in any form or by any means, electronic or mechanical, including photocopying and
microfilm, without permission in writing from the publisher.
International Organization for Standardization
Case postale 56 • CH-1211 Genève 20 • Switzerland
Internet [e-mail]
Printed in Switzerland
ii

---------------------- Page: 8 ----------------------

SIST EN ISO 10644:2001
INTERNATIONAL STANDARD  © ISO ISO 10644:1998(E)
Screw and washer assemblies with plain washers — Washer
hardness classes 200 HV and 300 HV
1 Scope
This International Standard specifies the requirements for metric screw and plain washer assemblies with coarse
thread M2 to M12 inclusive, flat seating heads, property classes up to and including 10.9 and washer hardness
classes 200 HV and 300 HV.
The plain washers are captive, i. e. prevented from disassembly and free to rotate.
2 Normative references
The following standards contain provisions which, through reference in this text, constitute provisions of this
International Standard. At the time of publication, the editions indicated were valid. All standards are subject to revision,
and parties to agreements based on this International Standard are encouraged to investigate the possibility of
applying the most recent editions of the standards indicated below. Members of IEC and ISO maintain registers of
currently valid International Standards.
ISO 898-1:1998, Mechanical properties of fasteners made of carbon steel and alloy steel — Part 1: Bolts, screws
and studs.
ISO 1207:1992, Slotted cheese head screws — Product grade A.
ISO 1580:1994, Slotted pan head screws — Product grade A.
1)
ISO 4014:— , Hexagon head bolts — Product grades A and B.
2)
ISO 4017:— , Hexagon head screws — Product grades A and B.
3)
ISO 4042:— , Fasteners — Electroplated coatings.
ISO 4762:1997, Hexagon socket head cap screws.
ISO 7045:1994, Pan head screws with type H or type Z cross recess — Product grade A.
ISO 10673:1998, Plain washers for screw and washer assemblies — Small, normal and large series — Product
grade A.
——————————
1)  To be published. (Revision of ISO 4014:1988)
2)  To be published. (Revision of ISO 4017:1988)
3)  To be published. (Revision of ISO 4042-1989)
1

---------------------- Page: 9 ----------------------

SIST EN ISO 10644:2001
© ISO
ISO 10644:1998(E)
3 Dimensions
The dimensions for the assembled screws shall conform to those in the ISO standards for loose parts with the
following exceptions:
– Bolts and screws shall have a reduced shank of such diam
...