Aerospace series - Flammability of non metallic materials - Part 1: Small burner test, vertical - Determination of the vertical flame propagation

This standard specifies the test method for the determination of the vertical flame propagation and after flame time of non metallic materials.
This test method is also used for testing non metallic materials which have to meet the test criteria for the vertical Bunsen burner test:
-   with a flame application time of 60 s;
-   with a flame application time of 12 s.
It is used for evaluation of non metallic materials or constructions used in the interiors of aerospace vehicles but may be used in other applications as specified in applicable procurement and regulatory documents.
This standard should be used to measure and describe the properties of non metallic materials, products or assemblies in response to heat and flame under controlled laboratory conditions and should not be used to describe or appraise the fire hazard or fire risk of materials, products, or assemblies under actual fire conditions. However, results of this test may be used as elements of a fire risk assessment which takes into account all of the factors which are pertinent to an assessment of the fire hazard of a particular end use.

Luft- und Raumfahrt - Entflammbarkeit nicht metallischer Werkstoffe - Teil 1: Kleinbrenner - Prüfung, senkrecht - Bestimmung der senkrechten Flammenausbreitung

Diese Europäische Norm legt das Prüfverfahren zur Bestimmung der senkrechten Flammenausbreitung und der Nachbrennzeit nichtmetallischer Werkstoffe fest.
Dieses Prüfverfahren wird ebenfalls zur Prüfung nichtmetallischer Werkstoffe verwendet, die die Prüfkriterien für die Bunsenbrennerprüfung (senkrecht) erfüllen müssen:
-   bei einer Beflammungszeit von 60 s;
-   bei einer Beflammungszeit von 12 s.
Es wird zur Bewertung nichtmetallischer Werkstoffe oder Konstruktionen verwendet, die im Inneren von Luft- und Raumfahrzeugen verwendet werden, aber in anderen Anwendungen verwendet werden können, wie in geltenden Dokumenten zu Auftragsvergabe und Rechtsvorschriften festgelegt.
Das vorliegende Dokument sollte zur Messung und Beschreibung der Eigenschaften nichtmetallischer Werkstoffe, Erzeugnisse oder Baugruppen angewendet werden, die unter kontrollierten Laborbedingungen Wärme und Beflammung ausgesetzt sind; sie sollte nicht für die Be¬schrei¬bung oder Bewertung der Brandgefahr oder des Brandrisikos von Werkstoffen, Erzeugnissen oder Bau¬gruppen bei realen Brandsituationen angewendet werden. Die Prüfergebnisse können jedoch möglicher¬weise als Elemente einer Bewertung des Brandrisikos verwendet werden, die alle Faktoren berücksichtigt, die eine Bewertung der Brandgefahr einer bestimmten Endanwendung nachhaltig beeinflussen.

Série aérospatiale - Inflammabilité des matériaux non métalliques - Partie 1: Essai au brûleur, vertical - Détermination de la propagation verticale de la flamme

Cette Norme européenne spécifie la méthode d’essai pour la détermination de la propagation verticale de la flamme et de la durée de flamme résiduelle des matériaux non métalliques.
Cette méthode d’essai est aussi utilisée pour tester les matériaux non métalliques qui doivent satisfaire les critères d’essai relatifs à l’essai au brûleur de Bunsen, vertical :
-   avec une durée d’application de la flamme de 60 s ;
-   avec une durée d’application de la flamme de 12 s.
Elle est utilisée pour évaluer les matériaux et les constructions non métalliques utilisés à l’intérieur des véhicules aérospatiaux mais elle peut être utilisée dans d’autres applications comme spécifié dans les documents d’approvisionnement et réglementaires applicables.
Il convient d’utiliser la présente norme pour mesurer et décrire les propriétés des matériaux, produits ou ensembles non métalliques en réponse à la chaleur et à la flamme dans des conditions contrôlées de laboratoire et non pas pour décrire ou évaluer les dangers ou les risques d’incendie des matériaux, produits ou ensembles dans des conditions réelles d'incendie. Toutefois, les résultats de cet essai peuvent être utilisés en tant qu’éléments d’évaluation des risques d’incendie qui tiennent compte de tous les facteurs pertinents pour faire une évaluation des dangers d’incendie liés à une utilisation finale particulière.

Aeronavtika - Vnetljivost nekovinskih materialov - 1. del: Preskus majhnih gorilnikov, navpični - Ugotavljanje navpičnega širjenja ognja

Ta evropski standard določa preskusno metodo za ugotavljanje navpičnega širjenja ognja in časa gorenja po odstranitvi vira vžiga nekovinskih materialov. Ta preskusna metoda se uporablja tudi za preskušanje nekovinskih materialov, ki morajo ustrezati preskusnim merilom za navpični preskus Bunsenovih gorilnikov: - s časom uporabe plamena 60 s; - s časom uporabe plamena 12 s. Uporablja se za vrednotenje nekovinskih materialov ali struktur, ki se uporabljajo v notranjosti aeronavtičnih plovil, lahko pa se uporablja tudi pri drugih aplikacijah, kot je določeno v veljavnih dokumentih za dobavo in zakonskih dokumentih. Ta standard se mora uporabljati za merjenje in opis lastnosti nekovinskih materialov, proizvodov ali sklopov kot odziv na toploto in ogenj v nadzorovanih laboratorijskih pogojih in se ne sme uporabljati za opis ali oceno požarne nevarnosti ali požarnega tveganja materialov, proizvodov ali sklopov v dejanskih požarnih razmerah. Rezultati tega preskusa pa se lahko uporabijo kot elementi ocene požarnega tveganja, ki upošteva vse dejavnike, ki se nanašajo na oceno požarne nevarnosti pri določeni končni uporabi.

General Information

Status
Withdrawn
Publication Date
22-Nov-2011
Withdrawal Date
08-Sep-2019
Technical Committee
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
09-Sep-2019
Due Date
02-Oct-2019
Completion Date
09-Sep-2019

RELATIONS

Buy Standard

Standard
SIST EN 3844-1:2012
English language
16 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
SIST EN 3844-1:2012
01-januar-2012
$HURQDYWLND9QHWOMLYRVWQHNRYLQVNLKPDWHULDORYGHO3UHVNXVPDMKQLK
JRULOQLNRYQDYSLþQL8JRWDYOMDQMHQDYSLþQHJDãLUMHQMDRJQMD

Aerospace series - Flammability of non metallic materials - Part 1: Small burner test,

vertical - Determination of the vertical flame propagation
Luft- und Raumfahrt - Entflammbarkeit nicht metallischer Werkstoffe - Teil 1:

Kleinbrenner - Prüfung, senkrecht - Bestimmung der senkrechten Flammenausbreitung

Série aérospatiale - Inflammabilité des matériaux non métalliques - Partie 1: Essai au

brûleur, vertical - Détermination de la propagation verticale de la flamme
Ta slovenski standard je istoveten z: EN 3844-1:2011
ICS:
13.220.99 Drugi standardi v zvezi z Other standards related to
varstvom pred požarom protection against fire
49.025.99 Drugi materiali Other materials
SIST EN 3844-1:2012 en,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 3844-1:2012
---------------------- Page: 2 ----------------------
SIST EN 3844-1:2012
EUROPEAN STANDARD
EN 3844-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2011
ICS 49.025.15
English Version
Aerospace series - Flammability of non metallic materials - Part
1: Small burner test, vertical - Determination of the vertical flame
propagation

Série aérospatiale - Inflammabilité des matériaux non Luft- und Raumfahrt - Entflammbarkeit nichtmetallischer

métalliques - Partie 1: Essai au brûleur, vertical - Werkstoffe - Teil 1: Kleinbrenner-Prüfung, senkrecht -

Détermination de la propagation verticale de la flamme Bestimmung der senkrechten Flammenausbreitung

This European Standard was approved by CEN on 10 March 2011.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European

Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national

standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation

under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same

status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,

Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.

EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels

© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 3844-1:2011: E

worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 3844-1:2012
EN 3844-1:2011 (E)
Contents

Foreword ............................................................................................................................................................. 3

1 Scope ..................................................................................................................................................... 4

2 Normative references ........................................................................................................................... 4

3 Terms and definitions ........................................................................................................................... 4

4 Principle of method .............................................................................................................................. 5

5 Designation ........................................................................................................................................... 5

6 Test apparatus ...................................................................................................................................... 5

7 Test specimens ..................................................................................................................................... 6

8 Conditioning .......................................................................................................................................... 7

9 Burner adjustment ................................................................................................................................ 7

10 Test procedure ...................................................................................................................................... 7

11 Report..................................................................................................................................................... 8

Bibliography ..................................................................................................................................................... 16

---------------------- Page: 4 ----------------------
SIST EN 3844-1:2012
EN 3844-1:2011 (E)
Foreword

This document (EN 3844-1:2011) has been prepared by the Aerospace and Defence Industries Association of

Europe - Standardization (ASD-STAN).

After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received

the approval of the National Associations and the Official Services of the member countries of ASD, prior to its

presentation to CEN.

This European Standard shall be given the status of a national standard, either by publication of an identical text or

by endorsement, at the latest by May 2012, and conflicting national standards shall be withdrawn at the latest by

May 2012.

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights.

CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following

countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech

Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,

Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden,

Switzerland and the United Kingdom.
---------------------- Page: 5 ----------------------
SIST EN 3844-1:2012
EN 3844-1:2011 (E)
1 Scope

This European Standard specifies the test method for the determination of the vertical flame propagation and after

flame time of non metallic materials.

This test method is also used for testing non metallic materials which have to meet the test criteria for the vertical

Bunsen burner test:
 with a flame application time of 60 s;
 with a flame application time of 12 s.

It is used for evaluation of non metallic materials or constructions used in the interiors of aerospace vehicles but

may be used in other applications as specified in applicable procurement and regulatory documents.

This standard should be used to measure and describe the properties of non metallic materials, products or

assemblies in response to heat and flame under controlled laboratory conditions and should not be used to

describe or appraise the fire hazard or fire risk of materials, products, or assemblies under actual fire conditions.

However, results of this test may be used as elements of a fire risk assessment which takes into account all of the

factors which are pertinent to an assessment of the fire hazard of a particular end use.

2 Normative references

The following referenced documents are indispensable for the application of this document. For dated references,

only the edition cited applies. For undated references, the latest edition of the referenced document (including any

amendments) applies.

ASTM-D 5025, A laboratory burner used for small-scale burning test on plastic materials

3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1
time of flame application
length of time for which the burner flame is applied to the specimen
3.2
after flame time

time in seconds for which the specimen continues to flame after the burner flame has been removed from the

specimen
3.3
after flame time of drips

time in seconds that any flaming material continues to flame after falling from the specimen to the bottom of the

chamber

1) Published by: ASTM National (US) American Society for Testing and Materials http://www.astm.org/.

---------------------- Page: 6 ----------------------
SIST EN 3844-1:2012
EN 3844-1:2011 (E)
3.4
burn length

distance in millimetres from the original specimen edge to the farthest evidence of damage of the test specimen

due to that area's combustion, including areas of partial consumption, charring, or embrittlement, but not including

areas sooted, stained, warped or discoloured, nor areas where material has shrunk or melted away from the heat

4 Principle of method

Testing is performed on a specimen that is held vertical. A burner flame, having defined parameters, is applied to

the specimen for a defined period of time. The after flame time and the burn length is measured. The occurrence of

drips and their after flame time is measured.
5 Desi
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.