SIST EN ISO 8099-2:2021
(Main)Small craft - Waste systems - Part 2: Sewage treatment systems (ISO 8099-2:2020)
Small craft - Waste systems - Part 2: Sewage treatment systems (ISO 8099-2:2020)
This document specifies requirements for the design, construction and installation of sewage treatment systems on small craft.
It does not address waste retention systems, nor accidental discharge prevention of pollutants (e.g. oil, fuel) overboard.
It does not address the technical discharge limits of a sewage treatment unit, subject to certain international as well as national regulations.
Kleine Wasserfahrzeuge - Abfallsysteme - Teil 2: Abwasserbehandlung (ISO 8099-2:2020)
Dieses Dokument legt die Anforderungen für Entwurf, Konstruktion und Montage von Schwarzwasser¬-Aufbereitungseinheiten auf kleinen Wasserfahrzeugen fest.
Dieses Dokument befasst sich weder mit Abfallrückhaltesystemen noch mit der Verhinderung der unbeabsichtigten Freisetzung von Schadstoffen (z. B. Öl, Brennstoff) nach außenbords.
Dieses Dokument befasst sich nicht mit den technischen Freisetzungsgrenzwerten einer Schwarzwasser¬-Aufbereitungseinheit, da diese Gegenstand bestimmter internationaler und nationaler Vorschriften sind.
Petits navires - Circuits d'eaux usées - Partie 2: Traitement des eaux usées (ISO 8099-2:2020)
Le présent document spécifie les exigences relatives à la conception, la construction et l'installation des systèmes de traitement des eaux usées sur les petits navires.
Ce document ne traite pas des systèmes de rétention des déchets, ni de la prévention des rejets accidentels de polluants (huile, carburant, etc.) par-dessus bord.
Il ne traite pas des limites techniques de rejets d'une unité de traitement des eaux usées, celles-ci étant soumises à certaines réglementations internationales et nationales.
Mala plovila - Sistemi ravnanja z odpadki - 2. del: Sistemi za čiščenje odplak (ISO 8099-2:2020)
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 8099-2:2021
01-junij-2021
Mala plovila - Sistemi ravnanja z odpadki - 2. del: Sistemi za čiščenje odplak (ISO
8099-2:2020)
Small craft - Waste systems - Part 2: Sewage treatment systems (ISO 8099-2:2020)
Kleine Wasserfahrzeuge - Abfallsysteme - Teil 2: Abwasserbehandlung (ISO 8099-
2:2020)
Petits navires - Circuits d'eaux usées - Partie 2: Traitement des eaux usées (ISO 8099-
2:2020)
Ta slovenski standard je istoveten z: EN ISO 8099-2:2021
ICS:
13.030.01 Odpadki na splošno Wastes in general
47.080 Čolni Small craft
SIST EN ISO 8099-2:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 8099-2:2021
---------------------- Page: 2 ----------------------
SIST EN ISO 8099-2:2021
EN ISO 8099-2
EUROPEAN STANDARD
NORME EUROPÉENNE
April 2021
EUROPÄISCHE NORM
ICS 47.080
English Version
Small craft - Waste systems - Part 2: Sewage treatment
systems (ISO 8099-2:2020)
Petits navires - Circuits d'eaux usées - Partie 2: Kleine Wasserfahrzeuge - Abfallsysteme - Teil 2:
Traitement des eaux usées (ISO 8099-2:2020) Abwasserbehandlung (ISO 8099-2:2020)
This European Standard was approved by CEN on 20 August 2020.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 8099-2:2021 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 8099-2:2021
EN ISO 8099-2:2021 (E)
Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Directive 2013/53/EU aimed to be covered . 4
2
---------------------- Page: 4 ----------------------
SIST EN ISO 8099-2:2021
EN ISO 8099-2:2021 (E)
European foreword
This document (EN ISO 8099-2:2021) has been prepared by Technical Committee ISO/TC 188 "Small
craft" in collaboration with CCMC.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by October 2021, and conflicting national standards shall
be withdrawn at the latest by October 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For the relationship with EU Directive(s) see informative Annex ZA, which is an integral part of this
document.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 8099-2:2020 has been approved by CEN as EN ISO 8099-2:2021 without any
modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 8099-2:2021
EN ISO 8099-2:2021 (E)
Annex ZA
(informative)
Relationship between this European Standard and the essential
requirements of Directive 2013/53/EU aimed to be covered
This European Standard has been prepared under a Commission’s standardization request M/542/C
(2015) 8736 final to provide one voluntary means of conforming to essential requirements of Directive
2013/53/EU.
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZA.1 confers, within the limits of
the scope of this standard, a presumption of conformity with the corresponding essential requirements
of that Directive and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and Annex I of Directive
2013/53/EU
Essential Requirements of Clause(s)/sub-clause(s) of this EN Remarks/Notes
Directive 2013/53/EU
Annex I, Part A, 2.5 – Owner’s 12
manual
Annex I, Part A, 5.8 – Discharge 4, 5, 6, 7, 8, 9 This standard only deals with the
prevention and installations prevention of accidental discharge of
facilitating the delivery ashore of sewage only; it does not deal with
waste. nor address:
— waste retention systems or;
— the accidental discharge of other
pollutants such as oil, fuel and bilge
water overboard.
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.
4
---------------------- Page: 6 ----------------------
SIST EN ISO 8099-2:2021
INTERNATIONAL ISO
STANDARD 8099-2
First edition
2020-12
Small craft — Waste systems —
Part 2:
Sewage treatment systems
Petits navires — Circuits d'eaux usées —
Partie 2: Traitement des eaux usées
Reference number
ISO 8099-2:2020(E)
©
ISO 2020
---------------------- Page: 7 ----------------------
SIST EN ISO 8099-2:2021
ISO 8099-2:2020(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 8099-2:2021
ISO 8099-2:2020(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 General requirements . 2
5 Materials . 3
6 Plumbing system . 4
6.1 Hoses and piping . 4
6.2 Seacocks . 4
7 Vent system . 4
8 Sewage holding tanks . 4
9 Pump-out fitting . 4
10 Labelling . 4
11 Installation, operation and maintenance manual . 5
12 Owner's manual . 6
Annex A (informative) Non-exhaustive list of existing discharge limits. 7
Bibliography . 8
© ISO 2020 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 8099-2:2021
ISO 8099-2:2020(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to
...
SLOVENSKI STANDARD
oSIST prEN ISO 8099-2:2019
01-julij-2019
Mala plovila - Sistemi ravnanja z odpadki - 2. del: Sistemi za čiščenje odplak
(ISO/DIS 8099-2:2019)
Small craft - Waste systems - Part 2: Sewage treatment systems (ISO/DIS 8099-2:2019)
Kleine Wasserfahrzeuge - Abfallsysteme - Teil 2: Abwasserbehandlung (ISO/DIS 8099-
2:2019)
Petits navires - Circuits d'eaux usées - Partie 2: Traitement des eaux usées (ISO/DIS
8099-2:2019)
Ta slovenski standard je istoveten z: prEN ISO 8099-2
ICS:
13.030.01 Odpadki na splošno Wastes in general
47.080 Čolni Small craft
oSIST prEN ISO 8099-2:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 8099-2:2019
---------------------- Page: 2 ----------------------
oSIST prEN ISO 8099-2:2019
DRAFT INTERNATIONAL STANDARD
ISO/DIS 8099-2
ISO/TC 188 Secretariat: SIS
Voting begins on: Voting terminates on:
2019-05-17 2019-08-09
Small craft — Waste systems —
Part 2:
Sewage treatment systems
Petits navires — Circuits d'eaux usées —
Partie 2: Traitement des eaux usées
ICS: 47.080
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 8099-2:2019(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2019
---------------------- Page: 3 ----------------------
oSIST prEN ISO 8099-2:2019
ISO/DIS 8099-2:2019(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 8099-2:2019
ISO/DIS 8099-2:2019(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 General requirements . 2
5 Materials . 3
6 Plumbing system . 4
6.1 Hoses and piping . 4
6.2 Seacock fitting . 4
7 Vent system . 4
8 Sewage holding tanks . 4
9 Pump-out fitting . 4
10 Labelling . 5
11 Installation, operation and maintenance manual . 5
Annex A (informative) Non- exhaustive list of existing discharge limits . 7
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Directive 2013/53/EU aimed to be covered . 8
Bibliography . 9
© ISO 2019 – All rights reserved iii
---------------------- Page: 5 ----------------------
oSIST prEN ISO 8099-2:2019
ISO/DIS 8099-2:2019(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity assessment,
as well as information about ISO's adherence to the World Trade Organization (WTO) principles in the
Technical Barriers to Trade (TBT) see the following URL: www .iso .org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 188, Small craft, together with CEN/BT/
WG 69, Small craft.
A list of all parts in the ISO 8099- series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/members .html.
iv © ISO 2019 – All rights reserved
---------------------- Page: 6 ----------------------
oSIST prEN ISO 8099-2:2019
DRAFT INTERNATIONAL STANDARD ISO/DIS 8099-2:2019(E)
Small craft — Waste systems —
Part 2:
Sewage treatment systems
1 Scope
This document specifies requirements for the design, construction, and installation of sewage treatment
systems on small craft.
This document does not address waste retention systems, nor accidental discharge prevention of
pollutants (oil, fuel, etc.) overboard.
ISO 8099-2 is not intended to address the technical discharge limits of a sewage treatment unit as these
are subject to certain international as well as national regulations.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 8099-1:2018, Small craft — Waste systems — Part 1: Waste water retention
ISO 228-1:2000, Pipe threads where pressure-tight joints are not made on the threads — Part 1: Dimensions,
tolerances and designation
ISO 9093-1:1994, Small craft — Seacocks and through-hull fittings — Part 1: Metallic
ISO 9093-2:2002, Small craft — Seacocks and through-hull fittings — Part 2: Non-metallic
ISO 10133:2012, Small craft — Electrical systems — Extra-low-voltage d.c. installations
ISO 13297:2014, Small craft — Electrical systems — Alternating current installations
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at http: //www .iso .org/obp
— IEC Electropedia: available at http: //www .electropedia .org/
3.1
sewage
black water
human body wastes and the wastes, including flushing water, from toilets and other receptacles
intended to receive or retain these wastes
Note 1 to entry: This includes any water that comes into direct contact with sewage.
© ISO 2019 – All rights reserved 1
---------------------- Page: 7 ----------------------
oSIST prEN ISO 8099-2:2019
ISO/DIS 8099-2:2019(E)
3.2
sewage treatment system
interconnected sanitation equipment including but not limited to the sewage treatment unit, hoses,
pipes, tanks and fittings designed for use on board small craft to treat, and dispose of treated sewage
3.3
sewage treatment unit
unit which processes sewage to reduce contaminants (e.g. Nitrogen, Phosphorous, Coliforms, suspended
solids etc.) to acceptable levels before discharge
Note 1 to entry: Acceptable levels may be subject to certain regulations, see Annex A.
3.4
accessible
capable of being reached for inspection, removal or maintenance without removal of the permanent
craft structure
3.5
readily accessible
capable
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.