SIST EN 61975:2010/A2:2023
(Amendment)High-voltage direct current (HVDC) installations - System tests (IEC 61975:2010/AMD2:2022)
High-voltage direct current (HVDC) installations - System tests (IEC 61975:2010/AMD2:2022)
Anlagen zur Hochspannungsgleichstromübertragung (HGÜ) - Systemprüfungen (IEC 61975:2010/AMD2:2022)
Installations en courant continu à haute tension (CCHT) - Essais systèmes (IEC 61975:2010/AMD2:2022)
Visokonapetostne enosmerne inštalacije (HVDC) - Sistemski preskusi - Dopolnilo A2 (IEC 61975:2010/AMD2:2022)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 61975:2010/A2:2023
01-februar-2023
Visokonapetostne enosmerne inštalacije (HVDC) - Sistemski preskusi - Dopolnilo
A2 (IEC 61975:2010/AMD2:2022)
High-voltage direct current (HVDC) installations - System tests (IEC
61975:2010/AMD2:2022)
Anlagen zur Hochspannungsgleichstromübertragung (HGÜ) - Systemprüfungen (IEC
61975:2010/AMD2:2022)
Installations en courant continu à haute tension (CCHT) - Essais systèmes (IEC
61975:2010/AMD2:2022)
Ta slovenski standard je istoveten z: EN 61975:2010/A2:2022
ICS:
29.130.10 Visokonapetostne stikalne in High voltage switchgear and
krmilne naprave controlgear
SIST EN 61975:2010/A2:2023 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 61975:2010/A2:2023
---------------------- Page: 2 ----------------------
SIST EN 61975:2010/A2:2023
EUROPEAN STANDARD EN 61975:2010/A2
NORME EUROPÉENNE
EUROPÄISCHE NORM December 2022
ICS 29.130.10; 31.080.01
English Version
High-voltage direct current (HVDC) installations - System tests
(IEC 61975:2010/AMD2:2022)
Installations en courant continu à haute tension (CCHT) - Anlagen zur Hochspannungsgleichstromübertragung (HGÜ)
Essais systèmes - Systemprüfungen
(IEC 61975:2010/AMD2:2022) (IEC 61975:2010/AMD2:2022)
This amendment A2 modifies the European Standard EN 61975:2010; it was approved by CENELEC on 2022-11-28. CENELEC members
are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this amendment the status of a
national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as
the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 61975:2010/A2:2022 E
---------------------- Page: 3 ----------------------
SIST EN 61975:2010/A2:2023
EN 61975:2010/A2:2022 (E)
European foreword
The text of document 22F/670/CDV, future IEC 61975/AMD2, prepared by SC 22F "Power electronics
for electrical transmission and distribution systems" of IEC/TC 22 "Power electronic systems and
equipment" was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
EN 61975:2010/A2:2022.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2023-08-28
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2025-11-28
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 61975:2010/AMD2:2022 was approved by CENELEC as a
European Standard without any modification.
2
---------------------- Page: 4 ----------------------
SIST EN 61975:2010/A2:2023
EN 61975:2010/A2:2022 (E)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
The Annex ZA of EN 61975:2010 applies with the following changes:
Publication Year Title EN/HD Year
Replace the reference to IEC 60633 with the following new reference:
IEC 60633 2019 High-voltage direct current (HVDC) EN IEC 60633 2019
transmission - Vocabulary
3
---------------------- Page: 5 ----------------------
SIST EN 61975:2010/A2:2023
---------------------- Page: 6 ----------------------
SIST EN 61975:2010/A2:2023
IEC 61975
®
Edition 1.0 2022-10
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
A MENDMENT 2
AM ENDEMENT 2
High-voltage direct current (HVDC) installations – System tests
Installations en courant continu à haute tension (CCHT) – Essais systèmes
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 29.130.10; 31.080.01 ISBN 978-2-8322-5839-2
Warning! Make sure that you obtained this publication from an authorized distributor.
Attention! Veuillez vous assurer que vous avez obtenu cette publication via un distributeur agréé.
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale
---------------------- Page: 7 ----------------------
SIST EN 61975:2010/A2:2023
– 2 – IEC 61975:2010/AMD2:2022
© IEC 2022
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
HIGH-VOLTAGE DIRECT CURRENT (HVDC)
INSTALLATIONS – SYSTEM TESTS
AMENDMENT 2
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC Publication(s)"). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. IEC shall not be held responsible for identifying any or all such patent rights.
Amendment 2 to IEC 61975:2010 has been prepared by subcommittee 22F: Power electronics
for electrical transmission and distribution systems, of IEC technical committee 22: Power
electronic systems and equipment.
The text of this Amendment is based on the following documents:
Draft Report on voting
22F/670/CDV 22F/691/RVC
Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this Amendment is English.
---------------------- Page: 8 ----------------------
SIST EN 61975:2010/A2:2023
IEC 61975:2010/AMD2:2022 – 3 –
© IEC 2022
This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
accordance with ISO/IEC Directives, P
...
SLOVENSKI STANDARD
SIST EN 61975:2010/oprA2:2022
01-marec-2022
Visokonapetostne enosmerne inštalacije (HVDC) - Sistemski preskusi - Dopolnilo
A2
Amendment 2 - High-voltage direct current (HVDC) installations - System tests
Anlagen zur Hochspannungsgleichstromübertragung (HGÜ) - Systemprüfungen
Installations en courant continu à haute tension (CCHT) - Essais systèmes
Ta slovenski standard je istoveten z: EN 61975:2010/prA2:2022
ICS:
29.130.10 Visokonapetostne stikalne in High voltage switchgear and
krmilne naprave controlgear
SIST EN 61975:2010/oprA2:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 61975:2010/oprA2:2022
---------------------- Page: 2 ----------------------
SIST EN 61975:2010/oprA2:2022
22F/670/CDV
COMMITTEE DRAFT FOR VOTE (CDV)
PROJECT NUMBER:
IEC 61975/AMD2 ED1
DATE OF CIRCULATION: CLOSING DATE FOR VOTING:
2022-01-07 2022-04-01
SUPERSEDES DOCUMENTS:
22F/638/CD, 22F/665A/CC
IEC SC 22F : POWER ELECTRONICS FOR ELECTRICAL TRANSMISSION AND DISTRIBUTION SYSTEMS
SECRETARIAT: SECRETARY:
Russian Federation Mr Lev Travin
OF INTEREST TO THE FOLLOWING COMMITTEES: PROPOSED HORIZONTAL STANDARD:
TC 115
Other TC/SCs are requested to indicate their interest, if any,
in this CDV to the secretary.
FUNCTIONS CONCERNED:
EMC ENVIRONMENT QUALITY ASSURANCE SAFETY
SUBMITTED FOR CENELEC PARALLEL VOTING NOT SUBMITTED FOR CENELEC PARALLEL VOTING
Attention IEC-CENELEC parallel voting
The attention of IEC National Committees, members of
CENELEC, is drawn to the fact that this Committee Draft for
Vote (CDV) is submitted for parallel voting.
The CENELEC members are invited to vote through the
CENELEC online voting system.
This document is still under study and subject to change. It should not be used for reference purposes.
Recipients of this document are invited to submit, with their comments, notification of any relevant patent rights of which they
are aware and to provide supporting documentation.
TITLE:
Amendment 2 - High-voltage direct current (HVDC) installations - System tests
PROPOSED STABILITY DATE: 2027
NOTE FROM TC/SC OFFICERS:
As the plenary meeting of SC 22F was cancelled in 2020 due to COVID-19 pandemic (see 22F/591/INF), the
decision to begin the review of IEC 61975 AMD1 ED1 by SC 22F/MT 27 in 2021 was proposed by SC 22F
secretariat and was supported by 100% voting of SC 22F P-members (see 22F/599/DC, 22F/609/INF).
Copyright © 2021 International Electrotechnical Commission, IEC. All rights reserved. It is permitted to download this
electronic file, to make a copy and to print out the content for the sole purpose of preparing National Committee positions.
You may not copy or "mirror" the file or printed version of the document, or any part of it, for any other purpose without
permission in writing from IEC.
---------------------- Page: 3 ----------------------
SIST EN 61975:2010/oprA2:2022
IEC 61975/AMD2/ED1/CDV © IEC (E) - 2 - 22F/670/CDV
It was noted that the Swedish IEC National Committee made 150 (!) comments on document 22F/638/CD but
most of them referred to the basic document IEC 61975 ED1.1 but not to the Amendment 1.
Compilation of comments 22F/665A/CC on document 22F/638/CD was considered by the secretary of SC 22F,
the Chair of SC 22F, Convenor and members of SC22F/MT27. It was decided to take into account only
comments referred to Amendment 1 as the rest ones could be used only for the revision of IS 61975 but not for
its review.
The Chair of SC 22F made decision (supported by the secretary of SC 22F) to prepare a CDV by putting agreed
changes into 22F/638/CD by 2021-12.
---------------------- Page: 4 ----------------------
SIST EN 61975:2010/oprA2:2022
IEC 61975/AMD2/ED1/CDV © IEC (E) - 3 - 22F/670/CDV
1 INTERNATIONAL ELECTROTECHNICAL COMMISSION
2 ____________
3
4 HIGH-VOLTAGE DIRECT CURRENT (HVDC) INSTALLATIONS - SYSTEM TESTS
5
6
7 AMENDMENT 2
8
9 FOREWORD
10 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all
11 national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-
12 operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to
13 other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available
14 Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical
15 committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work.
16 International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation.
17 IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions
18 determined by agreement between the two organizations.
19 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
20 consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC
21 National Committees.
22 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in
23 that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC
24 cannot be held responsible for the way in which they are used or for any misinterpretation by any end user.
25 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to
26 the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and
27 the corresponding national or regional publication shall be clearly indicated in the latter.
28 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment
29 services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by
30 independent certification bodies.
31 6) All users should ensure that they have the latest edition of this publication.
32 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of
33 its technical committees and IEC National Committees for any personal injury, property damage or other damage of any
34 nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the
35 publication, use of, or reliance upon, this IEC Publication or any other IEC Publications.
36 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
37 indispensable for the correct application of this publication.
38 9) Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. IEC
39 shall not be held responsible for identifying any or all such patent rights.
40 Amendment 2 to IEC 61975:2010 has been prepared by subcommittee 22F: POWER ELECTRONICS
41 FOR ELECTRICAL TRANSMISSION AND DISTRIBUTION SYSTEMS, of IEC technical committee 22:
42 POWER ELECTRONIC SYSTEMS AND EQUIPMENT.
43 The text of this Amendment is based on the following documents:
Draft Report on voting
22F/XX/FDIS 22F/XX/RVD
44
45 Full information on the voting for its approval can be found in the report on voting indicated in the
46 above table.
47 The language used for the development of this Amendment is English.
---------------------- Page: 5 ----------------------
SIST EN 61975:2010/oprA2:2022
IEC 61975/AMD2/ED1/CDV © IEC (E) - 4 - 22F/670/CDV
48 This document was drafted in accordance with ISO/IEC Directives, Part 2, and developed in
49 accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement, available at
50 www.iec.ch/members_experts/refdocs. The main document types developed by IEC are described in
51 greater detail at www.iec.ch/standardsdev/publications/.
52 The committee has decided that the contents of this document will remain unchanged until the stability
53 date indicated on the IEC website under webstore.iec.ch in the data related to the specific document.
54 At this date, the document will be
55 reconfirmed,
56 withdrawn,
57 replaced by a revised edition, or
58 amended.
59
60
61
62
63
64
---------------------- Page: 6 ----------------------
SIST EN 61975:2010/oprA2:2022
IEC 61975/AMD2/ED1/CDV © IEC (E) - 5 - 22F/670/CDV
65
66 2 Normative references
67
68 In the second paragraph, replace:
69
70 “IEC 60633:1998, Terminology for high-voltage direct current (HVDC) power transmission”
71
72 by:
73
74 “IEC 60633:2019, High-voltage direct current (HVDC) transmission - Vocabulary”
75
76
77 4.6.1 Factory system test
78
79 In the last paragraph, replace:
80
81 “Finding and correcting hardware and software errors in the control system is an important function of the off-
82 site test.”
83
84 by:
85
86 “Finding and correcting hardware and software errors in the control and protection system is an important
87 function of the off-site test.”
88
89 4.6.2 Additional simulation test
90
91 In the first paragraph, replace:
92
93 "…the additional simulation test shall be conducted, if specified by the user.”
94
95 by:
96
97 "…any additional simulation tests shall be conducted, if agreed upon between supplier and user."
98
99 In the last paragraph, replace:
100
101 “c) find and correct hardware and software errors in the control system which are easier to find and
102 correct…”
103
104 by:
105
106 “c) find and correct hardware and software errors in the control and protection system which are easier to
107 find and correct…”
108
109 Figure 4 – Structure of system test
110
111 In the paragraph “Power transmission test” item “8) Steady state performance”, replace:
112
113 “• Reactive power control end performance” by “• Reactive power control performance”
114
115 and replace:
116
117 “Overload/Temperature rise”
118
119 by
120
121 “• Overload Conditions
122 • Rated Load Temperature rise”
123
124
125
126
---------------------- Page: 7 ----------------------
SIST EN 61975:2010/oprA2:2022
IEC 61975/AMD2/ED1/CDV © IEC (E) - 6 - 22F/670/CDV
127
5.2.3.1 Low voltage energization
128
129 In the third paragraph, replace “b) The test may be performed by applying 0,5 to 10 kV…” by “b) The test
130 may be performed by applying 0,5 to 10 kV.
131
132 Transform Note into the following text:
133
134 “The preferred approach to verify the phasing of the converter main circuit connections and the
135 interconnections to the converter transformers is a thorough visual inspection of the interconnection scheme
136 and comparison with the relevant documentation. This will however include verification that the control sends
137 out a firing pulse to the correct thyristor.”
138
139 5.2.3.2 High voltage energization
140
141 In clause c), replace the text:
142
143 “Keep the transformer energized for a minimum of 6 h.”
144
145 by
146
147 “Keep the transformer energized for a minimum number of hours as specified by the manufacturer.”
148
149 5.5.3.2 Test procedure by emitting source
150
151 In the third paragraph, replace:
152
153 “b) Verify that the door of the DC control cubicles is closed.”
154
155 by:
156
157 “b) Verify that the doors of the control and protection cubicles are closed.”
158
159 5.5.4 Test acceptance criteria
160
161 Replace the existing text by “There shall be no abnormal control and protection actions during the test.”
162
163 5.6.1 General
164
165 Replace the existing text:
166
167 “The test should be conducted for each trip coil in the converter station and each pole before energizing of
168 the AC filters and transformers.”
169
170 by:
171
172 “The test should be conducted for each trip coil in the converter station and each pole before energizing of
173 the AC filters and converter transformers.”
174
175 5.7.3.1 Open line test of the DC switchyard
176
177 Delete “a) Connect the neutral side of the converter to earth or to the earth electrode (if available).” as it is
178 presented in clause (g) of 5.7.2.2.
179
180 Delete “f) Repeat the open line test of the DC switchyard with the appropriate DC filters connected one by
181 one and then together.” as it is not required
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.