SIST EN 61310-2:2008
Safety of machinery - Indication, marking and actuation -- Part 2: Requirements for marking
Safety of machinery - Indication, marking and actuation -- Part 2: Requirements for marking
This part of IEC 61310 specifies requirements for the marking of machinery. It gives general rules on marking for identification of machinery, for safe use related to mechanical and electrical hazards, and for the avoidance of hazards arising from incorrect connections.
Sicherheiten von Maschinen - Anzeigen, Kennzeichen und Bedienen - Teil 2: Anforderungen an die Kennzeichnung
Sécurité des machines - Indication, marquage et manoeuvre -- Partie 2: Exigences pour le marquage
spécifie des exigences concernant le marquage des machines, définit des règles générales de marquage pour l'identification des machines, pour leur utilisation sûre, relatives aux risques mécaniques et électriques, et pour éviter les risques liés à des liaisons erronées, comprend les modifications techniques significatives suivantes par rapport à l'édition précédente: Annexe A : signaux de sécurité supplémentaires inclus et mis à jour
Varnost strojev - Prikaz, oznaka in upravljanje - 2. del: Zahteve za označevanje (IEC 61310-2:2007)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 61310-2:2008
01-junij-2008
1DGRPHãþD
SIST EN 61310-2:1999
9DUQRVWVWURMHY3ULND]R]QDNDLQXSUDYOMDQMHGHO=DKWHYH]DR]QDþHYDQMH
,(&
Safety of machinery - Indication, marking and actuation - Part 2: Requirements for
marking
Sicherheit von Maschinen - Anzeigen, Kennzeichen und Bedienen - Teil 2:
Anforderungen an die Kennzeichnung
Sécurité des machines - Indication, marquage et manoeuvre - Partie 2: Exigences pour
le marquage
Ta slovenski standard je istoveten z: EN 61310-2:2008
ICS:
01.080.20 *UDILþQLVLPEROL]DSRVHEQR Graphical symbols for use on
RSUHPR specific equipment
13.110 Varnost strojev Safety of machinery
SIST EN 61310-2:2008 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
EN 61310-2
NORME EUROPÉENNE
January 2008
EUROPÄISCHE NORM
ICS 13.110 Supersedes EN 61310-2:1995
English version
Safety of machinery -
Indication, marking and actuation -
Part 2: Requirements for marking
(IEC 61310-2:2007)
Sécurité des machines - Sicherheiten von Maschinen -
Indication, marquage et manoeuvre - Anzeigen, Kennzeichen und Bedienen -
Partie 2: Exigences pour le marquage Teil 2: Anforderungen
(CEI 61310-2:2007) an die Kennzeichnung
(IEC 61310-2:2007)
This European Standard was approved by CENELEC on 2007-12-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: rue de Stassart 35, B - 1050 Brussels
© 2008 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61310-2:2008 E
---------------------- Page: 2 ----------------------
EN 61310-2:2008 – 2 –
Foreword
The text of document 44/541/FDIS, future edition 2 of IEC 61310-2, prepared by IEC TC 44, Safety of
machinery - Electrotechnical aspects, was submitted to the IEC-CENELEC parallel vote and was
approved by CENELEC as EN 61310-2 on 2007-12-01.
This European Standard supersedes EN 61310-2:1995.
EN 61310-2:2007 includes the following significant technical changes with respect to EN 61310-2:1995:
– Annex A: additional safety signs included and updated.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2008-09-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2010-12-01
This European Standard has been prepared under a mandate given to CENELEC by the European
Commission and the European Free Trade Association and covers essential requirements of
EC Directives MD (98/37/EC) and MD (2006/42/EC). See Annex ZZ.
Annexes ZA and ZZ have been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 61310-2:2007 was approved by CENELEC as a European
Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 61140 NOTE Harmonized as EN 61140:2002 (not modified).
IEC 61346-1 NOTE Harmonized as EN 61346-1:1996 (not modified).
__________
---------------------- Page: 3 ----------------------
– 3 – EN 61310-2:2008
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year
IEC 60027-1 1992 Letter symbols to be used in electrical EN 60027-1 2006
technology -
Part 1: General
IEC 60027-2 2005 Letter symbols to be used in electrical EN 60027-2 2007
technology -
Part 2: Telecommunications and electronics
IEC 60027-3 2002 Letter symbols to be used in electrical EN 60027-3 2007
technology -
Part 3: Logarithmic and related quantities,
and their units
1)
IEC 60027-4 1985 Letter symbols to be used in electrical HD 245.4 S1 1987
technology -
Part 4: Symbols for quantities to be used for
rotating electrical machines
IEC 60079-0 2004 Electrical apparatus for explosive gas EN 60079-0 2006
(mod) atmospheres -
Part 0: General requirements
IEC 60204-1 2005 Safety of machinery - Electrical equipment of EN 60204-1 2006
(mod) machines -
Part 1: General requirements
IEC 60417 Data Graphical symbols for use on equipment – –
base
IEC 60529 1989 Degrees of protection provided by EN 60529 1991
enclosures (IP Code) + corr. May 1993
A1 1999 A1 2000
2) 3)
IEC 61310-1 – Safety of machinery - Indication, marking EN 61310-1 2008
and actuation -
Part 1: Requirements for visual, acoustic and
tactile signals
ISO 31-0 1992 Quantities and units - – –
Part 0: General principles
1)
HD 245.4 S1 is superseded by EN 60027-4:2007, which is based on IEC 60027-4:2006.
2)
Undated reference.
3)
Valid edition at date of issue.
---------------------- Page: 4 ----------------------
EN 61310-2:2008 – 4 –
Publication Year Title EN/HD Year
ISO 1000 1992 SI units and recommendations for the use of – –
their multiples and of certain other units
ISO 7000 2004 Graphical symbols for use on equipment - – –
Index and synopsis
ISO 7010 2003 Graphical symbols - Safety colours and
– –
safety signs - Safety signs used in
workplaces and public areas
ISO 12100-1 2003 Safety of machinery - Basic concepts, EN ISO 12100-1 2003
general principles for design -
Part 1: Basic terminology, methodology
ISO 12100-2 2003 Safety of machinery - Basic concepts, EN ISO 12100-2 2003
general principles for design -
Part 2: Technical principles
---------------------- Page: 5 ----------------------
– 5 – EN 61310-2:2008
Annex ZZ
(informative)
Coverage of Essential Requirements of EC Directives
Annex ZZA
(informative)
Coverage of Essential Requirements of Directive 98/37/EC
This European Standard has been prepared under a mandate given to CENELEC by the European
Commission and the European Free Trade Association and within its scope the standard covers the
following essential requirements out of those given in Annex I of the EC Directive 98/37/EC, amended by
Directive 98/79/EC:
– ER 1.7.2;
– ER 1.7.3.
Compliance with this standard provides one means of conformity with the specified essential
requirements of the Directive concerned.
WARNING: Other requirements and other EC Directives may be applicable to the products falling within
the scope of this standard.
Annex ZZB
(informative)
Coverage of Essential Requirements of Directive 2006/42/EC
This European Standard has been prepared under a mandate given to CENELEC by the European
Commission and the European Free Trade Association and within its scope the standard covers the
following essential requirements out of those given in Annex I of the EC Directive 2006/42/EC:
– ER 1.7.1;
– ER 1.7.1.1;
– ER 1.7.1.2.
Compliance with this standard provides one means of conformity with the specified essential
requirements of the Directive concerned.
WARNING: Other requirements and other EC Directives may be applicable to the products falling within
the scope of this standard.
---------------------- Page: 6 ----------------------
NORME CEI
INTERNATIONALE
IEC
61310-2
INTERNATIONAL
Deuxième édition
STANDARD
Second edition
2007-02
Sécurité des machines –
Indication, marquage, manœuvre
Partie 2:
Exigences pour le marquage
Safety of machinery –
Indication, marking and actuation –
Part 2:
Requirements for marking
© IEC 2007 Droits de reproduction réservés ⎯ Copyright - all rights reserved
Aucune partie de cette publication ne peut être reproduite ni No part of this publication may be reproduced or utilized in any
utilisée sous quelque forme que ce soit et par aucun procédé, form or by any means, electronic or mechanical, including
électronique ou mécanique, y compris la photocopie et les photocopying and microfilm, without permission in writing from
microfilms, sans l'accord écrit de l'éditeur. the publisher.
International Electrotechnical Commission, 3, rue de Varembé, PO Box 131, CH-1211 Geneva 20, Switzerland
Telephone: +41 22 919 02 11 Telefax: +41 22 919 03 00 E-mail: inmail@iec.ch Web: www.iec.ch
CODE PRIX
M
PRICE CODE
Commission Electrotechnique Internationale
International Electrotechnical Commission
МеждународнаяЭлектротехническаяКомиссия
Pour prix, voir catalogue en vigueur
For price, see current catalogue
---------------------- Page: 7 ----------------------
61310-2 © IEC:2007 – 3 –
CONTENTS
FOREWORD.5
1 Scope.9
2 Normative references .9
3 Terms and definitions .11
4 Marking for identification and for safe use .11
4.1 General .11
4.2 Marking of complete machinery .13
4.3 Marking for safe use.13
5 Application of markings .15
5.1 General .15
5.2 Representation of rated values.17
6 Marking of connections.17
6.1 General .17
6.2 Mechanical connections .19
6.3 Connections for fluid systems.19
6.4 Electrical connections.19
7 Durability of markings and their attachment .19
Annex A (informative) Graphical symbols and safety signs .21
Bibliography.25
---------------------- Page: 8 ----------------------
61310-2 © IEC:2007 – 5 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
___________
SAFETY OF MACHINERY –
INDICATION, MARKING AND ACTUATION –
Part 2: Requirements for marking
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61310-2 has been prepared by IEC technical committee 44: Safety
of machinery – Electrotechnical aspects.
This second edition cancels and replaces the first edition published in 1995 and constitutes a
technical revision.
This edition includes the following signi
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.