SIST EN 10108:2004

Round steel rod for cold heading and cold extrusion - Dimensions and tolerances

This European Standard specifies the dimensions, the tolerances, the nominal cross-sections and the nominal masses of the round rod used for cold heading and cold extrusion.
This European Standard concerns the round rod in non alloy and alloy steel grades specified in European Standard EN 10263 parts 1 to 5.

Runder Walzdraht aus Kaltstauch- und Kaltfließpressstählen - Maße und Grenzabmaße

Dieses Dokument legt die Maße, Grenzabmaße, Nennquerschnitte und Nennmassen für runden Walzdraht zum Kaltstauchen und Kaltfließpressen fest.
Dieses Dokument gilt für runden Walzdraht aus den unlegierten und legierten Stahlsorten nach den Europäischen Normen EN 10263-1 bis EN 10263-5.

Fil machine rond en acier pour déformation a froid et extrusion a froid - Dimensions et tolérances

La présente Norme européenne spécifie les dimensions, les tolérances, les sections nominales et les masses
nominales des fils machine ronds utilisés pour les articles de boulonnerie formés a froid.
La présente Norme européenne concerne les fils machine ronds en nuances d?acier non allié et allié
spécifiées dans les EN 10263 Parties 1 a 5.

Okrogle jeklene palice za hladno nakrčevanje in hladno iztiskovanje – Mere in tolerance

General Information

• Status: Published
• Publication Date: 30-Nov-2004
• ICS: 77.140.65 - Steel wire, wire ropes and link chains
• Technical Committee: IFEK - Ferrous metals
• Current Stage: 6060 - National Implementation/Publication (Adopted Project)
• Start Date: 01-Dec-2004
• Due Date: 01-Dec-2004
• Completion Date: 01-Dec-2004
• Directive: 89/106/EEC - Construction products
• Directive: 97/23/EC - Directive 97/23/EC of the European Parliament and of the Council of 29 May 1997 on the approximation of the laws of the Member States concerning pressure equipment
• Mandate: M/071 - Mandate to CEN for standardization in the field of Pressure equipment
• Mandate: M/120 - Mandate to CEN/CENELEC concerning the execution of standardization work for harmonized standards on structural metallic products and ancillaries
• Ref Project: EN 10108:2004 - Round steel rod for cold heading and cold extrusion - Dimensions and tolerances

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.WROHUDQFHRunder Walzdraht aus Kaltstauch- und Kaltfließpressstählen - Maße und GrenzabmaßeFil machine rond en acier pour déformation a froid et extrusion a froid - Dimensions et tolérancesRound steel rod for cold heading and cold extrusion - Dimensions and tolerances77.140.65Jeklene žice, jeklene vrvi in verigeSteel wire, wire ropes and link chainsICS:Ta slovenski standard je istoveten z:EN 10108:2004SIST EN 10108:2004en01-december-2004SIST EN 10108:2004SLOVENSKI
STANDARD



SIST EN 10108:2004



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 10108
October 2004 ICS 77.140.65 Supersedes EURONORM 108:1972English version
Round steel rod for cold heading and cold extrusion - Dimensions and tolerances
Fil machine rond en acier pour déformation à froid et extrusion à froid - Dimensions et tolérances
Runder Walzdraht aus Kaltstauch-und kaltfließpressstählen - Maße und Grenzabmaße This European Standard was approved by CEN on 9 July 2004.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36
B-1050 Brussels © 2004 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 10108:2004: ESIST EN 10108:2004



EN 10108:2004 (E) 2 Content
page Foreword.3 1 Scope.4 2 Normative references.4 3 Terms and definitions.4 4 Information to be supplied by the purchaser.4 5 Requirements.5 6 Nominal sections and nominal masses.5 7 Dimensions and Tolerances.6 8 Mass of coils and checks on dimensional tolerances.10 9 Claims.10
SIST EN 10108:2004



EN 10108:2004 (E) 3 Foreword This document (EN 10108:2004) has been prepared by Technical Committee ECISS/TC 15 “Wire rod - Qualities, dimensions, tolerances and specific tests”, the secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2005, and conflicting national standards shall be withdrawn at the latest by April 2005. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). This document supersedes EURONORM 108:1972. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
SIST EN 10108:2004



EN 10108:2004 (E) 4 1 Scope This document specifies the dimensions, the tolerances, the nominal cross-sections and the nominal masses of the round rod used for cold heading and cold extrusion. This document concerns the round rod in non alloy and alloy steel grades specified in European Standard EN 10263 parts 1 to 5. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 10021, General technical delivery requirements for steel and iron products EN 10079:1992, Definition of steel products EN 10088-1, Stainless steels – Part 1: List of stainless steels EN 10263-1, Steel rod, bars and wire for cold heading and cold extrusion - Part 1: General technical delivery conditions EN 10263-2, Steel rod, bars and wire for cold heading and cold extrusion - Part 2: Technical delivery conditions for steels not intended for heat treatment after cold working EN 10263-3, Steel rod, bars and wire for cold heading and cold extrusion - Part 3: Technical delivery conditions for case hardening steels EN 10263-4, Steel rod, bars and wire for cold heading and cold extrusion - Part 4: Technical delivery conditions for steels for quenching and tempering EN 10263-5, Steel rod, bars and steel wire for cold heading and cold extrusion - Part 5: Technical delivery conditions for stainless steels 3 Terms and definitions For the purposes of
...