oSIST prEN 16810:2024
(Main)Resilient, textile, laminate and modular mechanical locked floor coverings, underlays - Environmental product declarations - Product category rules
Resilient, textile, laminate and modular mechanical locked floor coverings, underlays - Environmental product declarations - Product category rules
This document provides product category rules (PCR) for Type III environmental product declarations (EPD) for resilient, textile, laminate and modular mechanical locked floor coverings, as well for underlays specific to these floor coverings.
This document applies to the following products:
- resilient floor coverings manufactured from plastics, linoleum, cork or rubber, including loose-laid mats;
- textile floor coverings, including loose-laid mats, rugs and runners;
- laminate floor coverings;
- modular mechanical locked floor coverings;
- underlays.
An EPD can be developed for single or individual products, product groups and average products.
Elastische, textile, Laminat- und modulare mechanisch verriegelnde Bodenbeläge, Verlegeunterlagen - Umwelt-Produktdeklarationen - Produktkategorieregeln
Dieses Dokument enthält Produktkategorieregeln (en: product category rules, PCR) für Umweltproduktdeklarationen (en: environmental product declaration, EPD) für elastische, textile, Laminat- und modulare mechanisch verriegelnde Bodenbeläge sowie spezielle Unterlagen für diese Bodenbeläge.
Dieses Dokument gilt für folgende Produkte:
- elastische Bodenbeläge, die aus Kunststoff, Linoleum, Kork oder Kautschuk hergestellt sind, einschließlich lose verlegter Matten;
- textile Bodenbeläge, einschließlich lose verlegter Matten, Teppichen und Läufern;
- Laminat-Bodenbeläge;
- modulare mechanisch verriegelnde Fußbodenpaneelen;
- Unterlagen.
Eine EPD kann für einzelne oder individuelle Produkte, Produktgruppen und Durchschnittsprodukte entwickelt werden.
Revêtements de sol résilients, textiles, stratifiés et modulaires à clipsage mécanique, sous-couches - Déclarations environnementales des produits - Règles régissant les catégories de produits
Le présent document fournit des règles régissant les catégories de produits (PCR) pour les déclarations environnementales des produits (DEP) de Type III relatives aux revêtements de sol résilients, textiles, stratifiés et modulaires à clipsage mécanique, ainsi qu’aux sous-couches spécifiques à ces revêtements de sol.
Le présent document s’applique aux produits suivants :
- revêtements de sol résilients fabriqués à partir de matière plastique, de linoléum, de liège ou de caoutchouc, y compris les mats destinés à la pose flottante ;
- revêtements de sol textiles, y compris les mats destinés à la pose flottante, les carpettes et les tapis ;
- revêtements de sol stratifiés ;
- revêtements de sol modulaire à clipsage mécanique ;
- sous-couches.
Une DEP peut être établie pour des produits uniques ou individuels, des groupes de produits et des produits standards.
Netekstilne, tekstilne, laminirane in modularne mehansko zaklenjene talne obloge, podlage - Okoljske deklaracije za proizvode - Pravila za opredelitev vrste izdelka
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-december-2024
Netekstilne, tekstilne, laminirane in modularne mehansko zaklenjene talne obloge,
podlage - Okoljske deklaracije za proizvode - Pravila za opredelitev vrste izdelka
Resilient, textile, laminate and modular mechanical locked floor coverings, underlays -
Environmental product declarations - Product category rules
Elastische, textile, Laminat- und modulare mechanisch verriegelnde Bodenbeläge,
Verlegeunterlagen - Umwelt-Produktdeklarationen - Produktkategorieregeln
Revêtements de sol résilients, textiles, stratifiés et modulaires à clipsage mécanique,
sous-couches - Déclarations environnementales des produits - Règles régissant les
catégories de produits
Ta slovenski standard je istoveten z: prEN 16810
ICS:
13.020.50 Označevanje z ekološko Ecolabelling
nalepko
97.150 Talne obloge Floor coverings
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
DRAFT
EUROPEAN STANDARD
NORME EUROPÉENNE
EUROPÄISCHE NORM
September 2024
ICS 13.020.50; 97.150 Will supersede EN 16810:2017
English Version
Resilient, textile, laminate and modular mechanical locked
floor coverings, underlays - Environmental product
declarations - Product category rules
Revêtements de sol résilients, textiles, stratifiés et Elastische, textile, Laminat- und modulare mechanisch
modulaires à clipsage mécanique, sous-couches - verriegelnde Bodenbeläge, Verlegeunterlagen -
Déclarations environnementales des produits - Règles Umwelt-Produktdeklarationen -
régissant les catégories de produits Produktkategorieregeln
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee
CEN/TC 134.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations
which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 16810:2024 E
worldwide for CEN national Members.
Contents Page
European foreword . 4
Introduction . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 6
4 Abbreviated terms . 12
5 General aspects . 12
5.1 Objectives of product categorization rules . 12
5.2 EPD with respect to life cycle stages covered . 12
5.3 Comparability of EPD for floor coverings . 15
5.4 Additional environmental information . 16
5.5 Ownership, responsibility and liability for the EPD. 16
5.6 Communication formats . 16
6 Product Category Rules for LCA . 17
6.1 Product category . 17
6.2 Life cycle stages and their information modules to be included . 17
6.3 Calculation rules for the LCA . 18
6.4 Inventory analysis . 26
6.5 Impact assessment . 29
7 Content of the EPD . 30
7.1 Declaration of general information. 30
7.2 Declaration of environmental indicators derived from LCA . 33
7.3 Scenarios and additional technical information . 39
7.4 Additional information on release of dangerous substances to indoor air during the
use stage . 42
7.5 Aggregation of information modules . 43
8 Project report . 43
8.1 General. 43
8.2 Background report . 43
8.3 LCA-related elements of the project report. 43
8.4 Documentation on additional information . 45
8.5 Data availability for verification . 46
9 Verification and validity of an EPD . 46
Annex A (informative) Requirements and guidance on the service life . 47
Annex B (informative) Reference Service Life (RSL) for floor covering . 51
Annex C (informative) Waste . 52
C.1 End-of-waste . 52
C.2 Properties of hazardous waste for Table 9. 52
Annex D (informative) End of life formulae . 53
D.1 Introduction . 53
D.2 Terms and definitions . 53
D.3 Formulae . 56
Annex E (normative) Impact Categories and related indicators, methodologies and
characterization factors (CF) . 58
E.1 Core environmental impact categories and indicators . 58
E.2 Calculation rules for the climate change impact category . 59
E.3 Additional impact categories and indicators . 61
E.4 Characterization factors . 61
Bibliography . 62
European foreword
This document (prEN 16810:2024) has been prepared by Technical Committee CEN/TC 134 “Resilient,
textile, laminate and modular mechanical locked floor coverings”, the secretariat of which is held by NBN.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 16810:2017.
— underlays added to the scope;
— alignment of the standard with the latest updated version of EN 15804 i.e. EN 15804:2012+A2:2019;
— module A1, A2, A3 declared separately;
— module B3 as optional and to be adapted to the SL considered;
— integration of application rules for mass balance model.
Introduction
This document provides core product category rules for resilient, textile, laminate and modular
mechanical locked floor coverings. It is based on the principles laid down in EN 15804 and in
EN ISO 14025 and modified to suit the specific needs of the product families addressed in the scope of
this document.
It provides a structure to ensure that all Environmental Product Declarations (EPD) for resilient, textile
and laminate floor coverings processes are derived, verified and presented in a harmonized way.
An EPD communicates verifiable, accurate, non-misleading environmental information for products and
their applications, thereby supporting scientifically based, fair choices and stimulating the potential for
market driven continuous environmental improvement.
EPD information is expressed in information modules, which allow easy organization and expression of
data packages throughout the life cycle of the product. The approach requires that the underlying data
should be consistent, reproducible and comparable.
The EPD is expressed in a form that allows aggregation (addition) to provide complete information for
buildings. This document does not deal with aggregation at the building level nor does this document
describe the rules for applying EPD in a building assessment.
The document deals with a limited number of quantifiable predetermined parameters. Future revisions
may incorporate additional parameters.
This document provides the means for developing a Type III environmental declaration of resilient,
textile and laminate floor coverings.
1 Scope
This document provides product category rules (PCR) for Type III environmental product declarations
(EPD) for resilient, textile, laminate and modular mechanical locked floor coverings, as well for underlays
specific to these floor coverings.
This document applies to the following products:
— resilient floor coverings manufactured from plastics, linoleum, cork or rubber, including loose-laid
mats;
— textile floor coverings, including loose-laid mats, rugs and runners;
— laminate floor coverings;
— modular mechanical locked floor coverings;
— underlays.
An EPD can be developed for single or individual products, product groups and average products.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 15398, Resilient, textile, laminate and modular mechanical locked floor coverings (MMF) — Floor
covering standard symbols — Complementary element
EN 15804:2012+A2:2019 , Sustainability of construction works — Environmental product declarations —
Core rules for the product category of construction products
EN 15942, Sustainability of construction works — Environmental product declarations — Communication
format business-to-business
EN ISO 10874, Resilient, textile and laminate floor coverings — Classification (ISO 10874)
EN ISO 14025:2010, Environmental labels and declarations — Type III environmental declarati
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.