SIST EN 60309-2:2000
(Main)Plugs, socket-outlets and couplers for industrial purposes -- Part 2: Dimensional interchangeability requirements for pin and contact-tube accessories
Plugs, socket-outlets and couplers for industrial purposes -- Part 2: Dimensional interchangeability requirements for pin and contact-tube accessories
Applies to plugs and socket-outlets, cable couplers and appliance couplers with a rated operating voltage not exceeding 690 V, 500 Hz and a rated current not exceeding 125 A, primarily intended for industrial use, either indoors or outdoors. This standard applies to plugs and socket-outlets, cable couplers and appliance couplers with pins and contact tubes of standardized configurations. This standard applies to plugs and socket-outlets, cable couplers and appliance couplers, hereinafter referred to as accessories, for use when the ambient temperature is normally within the range -25 °C to 40 °C. The use of these accessories on building sites and for agricultural, commercial and domestic applications is not precluded. Socket-outlets or appliance inlets incorperated in or fixed to electrical equipment are within the scope of this standard. This standard also applies to accessories intended to be used in extralow voltage installations. This European Standard applies to Series I products only. Series II products are not allowed and not suitable for use in Europe: reference and requirements for. Series II products are reported in this standard for information only and shall be ignored. This European Standard applies to products intended to be used with cables with metric sizes (mm2) only. Reference and requirements to AWG and MCM cables are present in the relevant IEC publication and they are reported in this standard for information only. See Annex ZC for a list of references to Series II and/or AWG/MCM cable which are excluded from this standard.
Stecker, Steckdosen und Kupplungen für industrielle Anwendungen -- Teil 2: Anforderungen und Hauptmaße für die Austauschbarkeit von Stift- und Buchsensteckvorrichtungen
Prises de courant pour usages industriels -- Partie 2: Règles d'interchangeabilité dimensionnelle pour les appareils à broches et alvéoles
S'applique aux prises de courant, aux prolongateurs et aux connecteurs ayant une tension nominale d'emploi ne dépassant pas 690 V, 500 Hz et un courant nominal ne dépassant pas 125 A., destinés essentiellement aux usages industriels à l'intérieur ou à l'extérieur des bâtiments.
Vtiči, vtičnice in spojke za industrijske namene - 2. del: Zahteve za dimenzijsko izmenljivost pribora s trni in pušami (IEC 60309-2:1999)
Ta točka 1. dela ali 2. dela se uporablja, razen kot sledi: Zamenjava prvega odstavka z naslednjim besedilom: Ta del standarda IEC 60309 se uporablja za avtonomne izdelke, ki so združeni v enem ohišju, vtičnici ali priključku v skladu s standardom IEC 60309-1 ali IEC 60309-2, ter stikalno napravo z nazivno obratovalno napetostjo, ki ne presega 690 V enosmerne ali izmenične napetosti in 500 Hz, ter nazivnim tokom, ki ne presega 250 A, in so namenjeni predvsem za industrijsko uporabo v notranjih prostorih ali na prostem. Ti izdelki lahko vsebujejo zaporne in/ali varovalne naprave.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN 60309-2:2000
01-april-2000
1DGRPHãþD
SIST EN 60309-2:1999
9WLþLYWLþQLFHLQVSRMNH]DLQGXVWULMVNHQDPHQHGHO =DKWHYH]DGLPHQ]LMVNR
L]PHQOMLYRVWSULERUDVWUQLLQSXãDPL ,(&
Plugs, socket-outlets and couplers for industrial purposes -- Part 2: Dimensional
interchangeability requirements for pin and contact-tube accessories
Stecker, Steckdosen und Kupplungen für industrielle Anwendungen -- Teil 2:
Anforderungen und Hauptmaße für die Austauschbar
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.