Pigments and extenders - Methods of dispersion and assessment of dispersibility in plastics - Part 6: Determination by film test (ISO 23900-6:2015)

ISO 23900-6:2015 specifies a method assessing the degree of dispersion of colorants and/or extenders in a thermoplastic polymer. The method is suitable for testing colorants and/or extenders in the form of concentrates or compounds in all polymers used for extrusion processes.

Pigmente und Füllstoffe - Dispergierverfahren und Beurteilung der Dispergierbarkeit in Kunststoffen - Teil 6: Bestimmung mit dem Folientest (ISO 23900-6:2015)

Pigments et matières de charge - Méthodes de dispersion et évaluation de l'aptitude à la dispersion dans les plastiques - Partie 6: Détermination par essai de film (ISO 23900-6:2015)

ISO 23900-6:2015 spécifie une méthode d'évaluation du degré de dispersion des pigments[1] et/ou des matières de charge dans un polymère thermoplastique.
Cette méthode convient pour la mise à l'essai de pigments et/ou de matières de charge sous forme de concentrés ou de composés dans tous les polymères utilisés pour l'extrusion.
NOTE Les gels, tachetures noires, trous dans le film soumis à essai et autres défauts ne relèvent pas du domaine d'application de la présente partie de l'ISO 23900.
Le résultat de l'essai sur film déterminé par application de la présente méthode n'est valable que pour l'équipement, les conditions et le polymère d'essai utilisés. La mise en ?uvre de conditions d'essai différentes de celles spécifiées peut conduire à des résultats différents. Les méthodes de préparation des concentrés ou des composés ne sont pas spécifiées dans la présente partie de l'ISO 23900. Les résultats obtenus pour chacun des pigments ou des matières de charge ne sont donc comparables que si les conditions de préparation des concentrés ou des composés sont identiques et qu'un système de détection comparable est utilisé.
[1] Pour la définition de pigment, voir l?ISO 4618:2014, 2.60 matière colorante.

Pigmenti in polnila - Metode dispergiranja in ocenjevanje disperzibilnosti v polimernih materialih - 6. del: Določevanje s preskusom prevleke (ISO 23900-6:2015)

ISO 23900-6:2015 določa metodo ocenjevanja stopnje disperzije barvil in/ali polnil v termoplastičnem polimeru. Metoda je primerna za preskušanje barvil in/ali polnil v obliki koncentratov ali spojin v vseh polimerih, uporabljenih za postopke iztiskanja.

General Information

Status
Published
Public Enquiry End Date
04-Aug-2017
Publication Date
17-Oct-2018
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
09-Oct-2018
Due Date
14-Dec-2018
Completion Date
18-Oct-2018

RELATIONS

Buy Standard

Standard
SIST EN ISO 23900-6:2018
English language
17 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
SIST EN ISO 23900-6:2018
01-november-2018
1DGRPHãþD
SIST EN 13900-6:2014
3LJPHQWLLQSROQLOD0HWRGHGLVSHUJLUDQMDLQRFHQMHYDQMHGLVSHU]LELOQRVWLY
SROLPHUQLKPDWHULDOLKGHO'RORþHYDQMHVSUHVNXVRPSUHYOHNH ,62


Pigments and extenders - Methods of dispersion and assessment of dispersibility in

plastics - Part 6: Determination by film test (ISO 23900-6:2015)

Pigmente und Füllstoffe - Dispergierverfahren und Beurteilung der Dispergierbarkeit in

Kunststoffen - Teil 6: Bestimmung mit dem Folientest (ISO 23900-6:2015)

Pigments et matières de charge - Méthodes de dispersion et évaluation de l'aptitude à la

dispersion dans les plastiques - Partie 6: Détermination par essai de film (ISO 23900-

6:2015)
Ta slovenski standard je istoveten z: EN ISO 23900-6:2018
ICS:
83.080.01 Polimerni materiali na Plastics in general
splošno
87.060.10 Pigmenti in polnila Pigments and extenders
SIST EN ISO 23900-6:2018 en,fr,de

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 23900-6:2018
---------------------- Page: 2 ----------------------
SIST EN ISO 23900-6:2018
EN ISO 23900-6
EUROPEAN STANDARD
NORME EUROPÉENNE
September 2018
EUROPÄISCHE NORM
ICS 87.060.10 Supersedes EN 13900-6:2012
English Version
Pigments and extenders - Methods of dispersion and
assessment of dispersibility in plastics - Part 6:
Determination by film test (ISO 23900-6:2015)

Pigments et matières de charge - Méthodes de Pigmente und Füllstoffe - Dispergierverfahren und

dispersion et évaluation de l'aptitude à la dispersion Beurteilung der Dispergierbarkeit in Kunststoffen -

dans les plastiques - Partie 6: Détermination par essai Teil 6: Bestimmung mit dem Folientest (ISO 23900-

de film (ISO 23900-6:2015) 6:2015)
This European Standard was approved by CEN on 12 August 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this

European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references

concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN

member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by

translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management

Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,

Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,

Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,

Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels

© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 23900-6:2018 E

worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 23900-6:2018
EN ISO 23900-6:2018 (E)
Contents Page

European foreword ....................................................................................................................................................... 3

---------------------- Page: 4 ----------------------
SIST EN ISO 23900-6:2018
EN ISO 23900-6:2018 (E)
European foreword

The text of ISO 23900-6:2015 has been prepared by Technical Committee ISO/TC 256 "Pigments,

dyestuffs and extenders” of the International Organization for Standardization (ISO) and has been taken

over as EN ISO 23900-6:2018 by Technical Committee CEN/TC 298 “Pigments and extenders” the

secretariat of which is held by DIN.

This European Standard shall be given the status of a national standard, either by publication of an

identical text or by endorsement, at the latest by March 2019, and conflicting national standards shall

be withdrawn at the latest by March 2019.

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. CEN shall not be held responsible for identifying any or all such patent rights.

This document supersedes EN 13900-6:2012.

According to the CEN-CENELEC Internal Regulations, the national standards organizations of the

following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,

Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,

France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,

Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,

Turkey and the United Kingdom.
Endorsement notice

The text of ISO 23900-6:2015 has been approved by CEN as EN ISO 23900-6:2018 without any

modification.
---------------------- Page: 5 ----------------------
SIST EN ISO 23900-6:2018
---------------------- Page: 6 ----------------------
SIST EN ISO 23900-6:2018
INTERNATIONAL ISO
STANDARD 23900-6
First edition
2015-05-01
Pigments and extenders — Methods
of dispersion and assessment of
dispersibility in plastics —
Part 6:
Determination by film test
Pigments et matières de charge — Méthodes de dispersion et
évaluation de l’aptitude à la dispersion dans les plastiques —
Partie 6: Détermination par essai de film
Reference number
ISO 23900-6:2015(E)
ISO 2015
---------------------- Page: 7 ----------------------
SIST EN ISO 23900-6:2018
ISO 23900-6:2015(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2015

All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form

or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior

written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of

the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2015 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 23900-6:2018
ISO 23900-6:2015(E)
Contents Page

Foreword ........................................................................................................................................................................................................................................iv

1 Scope ................................................................................................................................................................................................................................. 1

2 Terms and definitions ..................................................................................................................................................................................... 1

3 Principle ........................................................................................................................................................................................................................ 3

4 Materials ....................................................................................................................................................................................................................... 4

4.1 Concentrate ................................................................................................................................................................................................ 4

4.2 Basic test polymer ................................................................................................................................................................................ 4

4.3 Test mixture ............................................................................................................................................................................................... 4

5 Apparatus ..................................................................................................................................................................................................................... 5

6 Preparation of test mixtures .................................................................................................................................................................... 5

6.1 General ........................................................................................................................................................................................................... 5

6.2 Test mixture ............................................................................................................................................................................................... 5

7 Procedure..................................................................................................................................................................................................................... 5

7.1 Calibration .................................................................................................................................................................................................. 5

7.2 Size ranges and resolution ............................................................................................................................................................ 6

7.3 Pre-conditioning .................................................................................................................................................................................... 7

7.4 Test procedure ......................................................................................................................................................................................... 8

7.4.1 Production of the test polymer film ................................................................................................................ 8

7.4.2 Production of the test mixture film .................. ................................................................................................ 8

8 Evaluation .................................................................................................................................................................................................................... 9

9 Test report ................................................................................................................................................................................................................... 9

10 Precision ....................................................................................................................................................................................................................... 9

Bibliography .............................................................................................................................................................................................................................10

© ISO 2015 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 23900-6:2018
ISO 23900-6:2015(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards

bodies (ISO member bodies). The work of preparing International Standards is normally carried out

through ISO technical committees. Each member body interested in a subject for which a technical

committee has been established has the right to be represented on that committee. International

organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.

ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of

electrotechnical standardization.

The procedures used to develop this document and those intended for its further maintenance are

described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the

different types of ISO documents should be noted. This document was drafted in accordance with the

editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any

patent rights identified during the development of the document will be in the Introduction and/or on

the ISO list of patent declarations received (see www.iso.org/patents).

Any trade name used in this document is information given for the convenience of users and does not

constitute an endorsement.

For an explanation on the meaning of ISO specific terms and expressions related to conformity

assessment, as well as information about ISO’s adherence to the WTO principles in the Technical Barriers

to Trade (TBT), see the following URL: Foreword — Supplementary information.

The committee responsible for this document is ISO/TC 256, Pigments, dyestuffs and extenders.

ISO 23900 consists of the following parts, under the general title Pigments and extenders — Methods of

dispersion and assessment of dispersibility in plastics:
— Part 1: General introduction

— Part 2: Determination of colouristic properties and ease of dispersion in plasticized polyvinyl chloride

by two-roll milling

— Part 3: Determination of colouristic properties and ease of dispersion of black and colour pigments in

polyethylene by two-roll milling

— Part 4: Determination of colouristic properties and ease of dispersion of white pigments in polyethylene

by two-roll milling
— Part 5: Determination by filter pressure value test
— Part 6: Determination by film test
iv © ISO 2015 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 23900-6:2018
INTERNATIONAL STANDARD ISO 23900-6:2015(E)
Pigments and extenders — Methods of dispersion and
assessment of dispersibility in plastics —
Part 6:
Determination by film test
1 Scope
This part of ISO 23900 specifies a method asse
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.