SIST EN ISO/ASTM 52903-1:2021
(Main)Additive manufacturing - Material extrusion-based additive manufacturing of plastic materials - Part 1: Feedstock materials (ISO/ASTM 52903-1:2020)
Additive manufacturing - Material extrusion-based additive manufacturing of plastic materials - Part 1: Feedstock materials (ISO/ASTM 52903-1:2020)
This document describes a method for defining requirements for plastic materials used in extrusion-based additive manufacturing (AM) processes. Materials include unfilled, filled, and reinforced plastic materials suitable for processing into parts. These materials can also contain special additives (e.g. flame retardants, stabilizers, etc.). Processes include all material extrusion-based AM processes.
This document is intended for use by manufacturers of materials, feedstocks, plastic parts or any combination of the three using material extrusion-based AM.
NOTE In some cases, material manufacturers can also be feedstock manufacturers. In other cases, a material manufacturer can supply materials (example: pellets) to a feedstock manufacturer (example: converter of pellets into filaments).
This document does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health, and environmental practices and determine the applicability of regulatory limitations prior to use.
Additive Fertigung - Materialextrusion-basierte additive Fertigung von Kunststoffen - Teil 1: Ausgangsmaterialien (ISO/ASTM 52903-1:2020)
Dieses Dokument beschreibt ein Verfahren zur Definition von Anforderungen an Kunststoffmaterialien, die in additiven Fertigungsprozessen (AM, en: additive manufacturing) auf Grundlage von Werkstoffextrusion verwendet werden. Materialien beinhalten nicht gefüllte, gefüllte und verstärkte Kunststoffmaterialien, die für die Verarbeitung zu Teilen geeignet sind. Diese Kunststoffe können auch spezielle Additive (z. B. Flammschutzmittel, Stabilisatoren usw.) enthalten. Die Prozesse umfassen alle AM-Prozesse auf Grundlage von Werkstoffextrusion.
Dieses Dokument ist zur Nutzung durch Hersteller von Werkstoffen, Ausgangsmaterialien, Kunststoffteilen oder jeglicher Kombination der drei unter Verwendung von AM auf Grundlage von Werkstoffextrusion vorgesehen.
ANMERKUNG In manchen Fällen können Werkstoffhersteller auch Ausgangsmaterialhersteller sein. In anderen Fällen kann ein Werkstoffhersteller einem Ausgangsmateriallieferanten (Beispiel: Umformung von Granulat in Filamente) Werkstoffe (Beispiel: Granulat) bereitstellen.
In diesem Dokument werden nicht alle Sicherheitsrisiken, falls vorhanden, behandelt, die bei Anwendung der Norm auftreten können. Es liegt in der Verantwortung des Anwenders dieses Dokuments, geeignete Vorkehrungen für den Arbeits-, Gesundheits- und Umweltschutz zu treffen und vor der Anwendung festzulegen, welche einschränkenden Vorschriften gelten.
Fabrication additive - Fabrication additive de matériaux plastiques à base d'extrusion de matière - Partie 1: Matières premières (ISO/ASTM 52903-1:2020)
Le présent document décrit une méthode pour définir les exigences pour les matériaux plastiques utilisés dans les procédés de fabrication additive (FA) à base d'extrusion. Les matériaux comprennent des matériaux plastiques non filaires, filaires et renforcées adaptées à la transformation en pièces. Ces matériaux peuvent également contenir des additifs spéciaux (par exemple, retardateurs de flamme, stabilisants, etc.). Les procédés comprennent tous les procédés de FA à base d'extrusion de matière.
Le présent document est destiné à être utilisé par les fabricants de matériaux, matières premières, pièces en matière plastique ou toute combinaison des trois utilisant la FA à base d'extrusion de matière.
NOTE Dans certains cas, les fabricants de matériaux peuvent également être des fabricants de matières premières. Dans d'autres cas, un fabricant de matériaux peut fournir des matériaux (exemple: pastilles) à un fabricant de matières premières (exemple: conversion de pastilles en filaments).
Le présent document ne prétend pas répondre à toutes les préoccupations en matière de sécurité, le cas échéant, associés à son utilisation. Il est de la responsabilité de l'utilisateur de la présente norme d'établir des pratiques appropriées de sécurité et de santé, et environnementales et de déterminer l'applicabilité des restrictions réglementaires avant utilisation.
Aditivna proizvodnja - Aditivna proizvodnja plastičnih materialov z ekstruzijo - 1. del: Surovine (ISO/ASTM 52903-1:2020)
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO/ASTM 52903-1:2021
01-maj-2021
Aditivna proizvodnja - Aditivna proizvodnja plastičnih materialov z ekstruzijo - 1.
del: Surovine (ISO/ASTM 52903-1:2020)
Additive manufacturing - Material extrusion-based additive manufacturing of plastic
materials - Part 1: Feedstock materials (ISO/ASTM 52903-1:2020)
Additive Fertigung - Materialextrusion-basierte additive Fertigung von Kunststoffen - Teil
1: Ausgangsmaterialien (ISO/ASTM 52903-1:2020)
Fabrication additive - Fabrication additive de matériaux plastiques à base d'extrusion de
matière - Partie 1: Matières premières (ISO/ASTM 52903-1:2020)
Ta slovenski standard je istoveten z: EN ISO/ASTM 52903-1:2021
ICS:
25.030 3D-tiskanje Additive manufacturing
83.080.01 Polimerni materiali na Plastics in general
splošno
SIST EN ISO/ASTM 52903-1:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO/ASTM 52903-1:2021
---------------------- Page: 2 ----------------------
SIST EN ISO/ASTM 52903-1:2021
EN ISO/ASTM 52903-1
EUROPEAN STANDARD
NORME EUROPÉENNE
March 2021
EUROPÄISCHE NORM
ICS 25.030
English Version
Additive manufacturing - Material extrusion-based
additive manufacturing of plastic materials - Part 1:
Feedstock materials (ISO/ASTM 52903-1:2020)
Fabrication additive - Fabrication additive de Additive Fertigung - Materialextrusion-basierte
matériaux plastiques à base d'extrusion de matière - additive Fertigung von Kunststoffen - Teil 1:
Partie 1: Matières premières (ISO/ASTM 52903- Ausgangsmaterialien (ISO/ASTM 52903-1:2020)
1:2020)
This European Standard was approved by CEN on 1 March 2021.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO/ASTM 52903-1:2021 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO/ASTM 52903-1:2021
EN ISO/ASTM 52903-1:2021 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO/ASTM 52903-1:2021
EN ISO/ASTM 52903-1:2021 (E)
European foreword
The text of ISO/ASTM 52903-1:2020 has been prepared by Technical Committee ISO/TC 261 "Additive
manufacturing” of the International Organization for Standardization (ISO) and has been taken over as
EN ISO/ASTM 52903-1:2021 by Technical Committee CEN/TC 438 “Additive Manufacturing” the
secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2021, and conflicting national standards
shall be withdrawn at the latest by September 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO/ASTM 52903-1:2020 has been approved by CEN as EN ISO/ASTM 52903-1:2021
without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO/ASTM 52903-1:2021
---------------------- Page: 6 ----------------------
SIST EN ISO/ASTM 52903-1:2021
INTERNATIONAL ISO/ASTM
STANDARD 52903-1
First edition
2020-04
Additive manufacturing —
Material extrusion-based additive
manufacturing of plastic materials —
Part 1:
Feedstock materials
Fabrication additive — Fabrication additive de matériaux plastiques
à base d'extrusion de matière —
Partie 1: Matières premières
Reference number
ISO/ASTM 52903-1:2020(E)
©
ISO/ASTM International 2020
---------------------- Page: 7 ----------------------
SIST EN ISO/ASTM 52903-1:2021
ISO/ASTM 52903-1:2020(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO/ASTM International 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may be
reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester. In the United States, such requests should be sent to ASTM International.
ISO copyright office ASTM International
CP 401 • Ch. de Blandonnet 8 100 Barr Harbor Drive, PO Box C700
CH-1214 Vernier, Geneva West Conshohocken, PA 19428-2959, USA
Phone: +41 22 749 01 11 Phone: +610 832 9634
Fax: +41 22 749 09 47 Fax: +610 832 9635
Email: copyright@iso.org Email: khooper@astm.org
Website: www.iso.org Website: www.astm.org
Published in Switzerland
ii © ISO/ASTM International 2020 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO/ASTM 52903-1:2021
ISO/ASTM 52903-1:2020(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Materials . 2
4.1 Material classification . 2
4.2 Manufactured feedstock. 2
5 Certification . 2
6 Material packaging and package marking . 2
7 Quality assurance . 3
Annex A (normative) Standard nomenclature of feedstock plastic materials .4
Bibliography . 5
© ISO/ASTM International 2020 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO/ASTM 52903-1:2021
ISO/ASTM 52903-1:2020(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso .org/
iso/ foreword .html.
This document was prepared by ISO/TC 261, Additive manufacturing, in cooperation with ASTM F 42,
Additive manufacturing technologies, on the basis of a partnership agreement between ISO and ASTM
International with the aim to create a common set of ISO/ASTM standards on additive manufacturing.
A list of all parts in the ISO/ASTM 52903 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO/ASTM International 2020 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO/ASTM 52903-1:2021
INTERNATIONAL STANDARD ISO/ASTM 52903-1:2020(E)
Additive manufacturing — Material extrusion-based
additive manufacturing of plastic materials —
Part 1:
Feedstock materials
1 Scope
This document describes a method for defining requirements for plastic materials used in extrusion-
based additive manufacturing (AM) processes. Materials include unfilled, filled, and reinforced plastic
materials suitable for processing into parts. These materials can also contain special additi
...
SLOVENSKI STANDARD
oSIST prEN ISO/ASTM 52903-1:2021
01-januar-2021
Aditivna proizvodnja - Izdelava aditivov iz polimernih materialov na osnovi
ekstrudiranja materialov - 1. del: Surovine (ISO/ASTM 52903-1:2020)
Additive manufacturing - Material extrusion-based additive manufacturing of plastic
materials - Part 1: Feedstock materials (ISO/ASTM 52903-1:2020)
Additive Fertigung - Materialextrusion-basierte additive Fertigung von Kunststoffen - Teil
1: Ausgangsmaterialien (ISO/ASTM 52903-1:2020)
Fabrication additive - Fabrication additive de matériaux plastiques à base d'extrusion de
matière - Partie 1: Matières premières (ISO/ASTM 52903-1:2020)
Ta slovenski standard je istoveten z: prEN ISO/ASTM 52903-1
ICS:
25.030 3D-tiskanje Additive manufacturing
83.080.01 Polimerni materiali na Plastics in general
splošno
oSIST prEN ISO/ASTM 52903-1:2021 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO/ASTM 52903-1:2021
---------------------- Page: 2 ----------------------
oSIST prEN ISO/ASTM 52903-1:2021
INTERNATIONAL ISO/ASTM
STANDARD 52903-1
First edition
2020-04
Additive manufacturing —
Material extrusion-based additive
manufacturing of plastic materials —
Part 1:
Feedstock materials
Fabrication additive — Fabrication additive de matériaux plastiques
à base d'extrusion de matière —
Partie 1: Matières premières
Reference number
ISO/ASTM 52903-1:2020(E)
©
ISO/ASTM International 2020
---------------------- Page: 3 ----------------------
oSIST prEN ISO/ASTM 52903-1:2021
ISO/ASTM 52903-1:2020(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO/ASTM International 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may be
reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester. In the United States, such requests should be sent to ASTM International.
ISO copyright office ASTM International
CP 401 • Ch. de Blandonnet 8 100 Barr Harbor Drive, PO Box C700
CH-1214 Vernier, Geneva West Conshohocken, PA 19428-2959, USA
Phone: +41 22 749 01 11 Phone: +610 832 9634
Fax: +41 22 749 09 47 Fax: +610 832 9635
Email: copyright@iso.org Email: khooper@astm.org
Website: www.iso.org Website: www.astm.org
Published in Switzerland
ii © ISO/ASTM International 2020 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO/ASTM 52903-1:2021
ISO/ASTM 52903-1:2020(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Materials . 2
4.1 Material classification . 2
4.2 Manufactured feedstock. 2
5 Certification . 2
6 Material packaging and package marking . 2
7 Quality assurance . 3
Annex A (normative) Standard nomenclature of feedstock plastic materials .4
Bibliography . 5
© ISO/ASTM International 2020 – All rights reserved iii
---------------------- Page: 5 ----------------------
oSIST prEN ISO/ASTM 52903-1:2021
ISO/ASTM 52903-1:2020(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso .org/
iso/ foreword .html.
This document was prepared by ISO/TC 261, Additive manufacturing, in cooperation with ASTM F 42,
Additive manufacturing technologies, on the basis of a partnership agreement between ISO and ASTM
International with the aim to create a common set of ISO/ASTM standards on additive manufacturing.
A list of all parts in the ISO/ASTM 52903 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO/ASTM International 2020 – All rights reserved
---------------------- Page: 6 ----------------------
oSIST prEN ISO/ASTM 52903-1:2021
INTERNATIONAL STANDARD ISO/ASTM 52903-1:2020(E)
Additive manufacturing — Material extrusion-based
additive manufacturing of plastic materials —
Part 1:
Feedstock materials
1 Scope
This document describes a method for defining requirements for plastic materials used in extrusion-
based additive manufacturing (AM) processes. Materials include unfilled, filled, and reinforced plastic
materials suitable for processing into parts. These materials can also contain special additives (e.g.
flame retardants, stabilizers, etc.). Processes include all material extrusion-based AM processes.
This document is intended for use by manufacturers of materials, feedstocks, plastic parts or any
combination of the three using material extrusion-based AM.
NOTE In some cases, material manufacturers can also be feedstock manufacturers. In other cases, a material
manufacturer can supply materials (example: pellets) to a feedstock manufacturer (example: converter of pellets
into filaments).
This document does not purport to address all of the safety concerns, if any, associated with its use.
It is the responsibility of the user of this standard to establish appropriate safety and health, and
environmental practices and determine the applicability of regulatory limitations prior to use.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO/ASTM 52900, Additive Manufacturing — General Principles — Fundamentals and vocabulary
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO/ASTM 52900 and the
following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at http:// www .electropedia .org/
3.1
filament
feedstock characterized by extreme length relative to its uniform cross section
3.2
pellets
small mass of preformed feedstock material, having relative uniform dimensions in any given batch
Note 1 to entry: Pellets of smaller size can sometimes be referred to as micro-pellets.
© ISO/ASTM International 2020 – All rights reserved 1
---------------------- Page: 7 ----------------------
oSIST prEN ISO/ASTM 52903-1:2021
ISO/AS
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.