SIST EN ISO 27548:2025
(Main)Additive manufacturing of plastics - Environment, health, and safety - Test method for determination of particle and chemical emission rates from desktop material extrusion 3D printer (ISO 27548:2024)
Additive manufacturing of plastics - Environment, health, and safety - Test method for determination of particle and chemical emission rates from desktop material extrusion 3D printer (ISO 27548:2024)
This document specifies test methods to determine particle emissions (including ultrafine particles) and specified VOCs (including aldehydes) from Material Extrusion(ME) processes often used in non-industrial environments such as school, homes and office spaces in an Emission Test Chamber (ETC) under specified test conditions. However, these tests may not accurately predict real-world results.
This document describes a conditioning method using an ETC with controlled temperature, humidity, air exchange rate, air velocity, and procedures for monitoring, storage, analysis, calculation, and reporting of emission rates.
This document is intended to cover a Fused Filament Fabrication (FFF) type desktop 3D printer using thermoplastic materials. The primary purpose of this document is to quantify particle and chemical emission rates emitted from a specific ME type desktop 3D printer which is operated using thermoplastic feedstocks.
However, not all possible emissions are covered by this method. Many feedstocks could release hazardous emissions that are not measured by the chemical detectors prescribed in this document. It is the responsibility of the user to understand the material being printed and the potential chemical emissions. An example is PVC feedstocks that could potentially emit chlorinated compounds, which would not be measured by this document.
Additive Fertigung von Kunststoffen - Umwelt, Gesundheit und Sicherheit - Prüfverfahren zur Bestimmung der Partikelemissionsrate und der chemischen Emissionsrate von materialextrusionsbasierten Desktop-3D-Druckern (ISO 27548:2024)
Dieses Dokument legt Prüfverfahren zur Bestimmung der Partikelemissionen (einschließlich ultrafeiner Partikel) und angegebenen flüchtigen organischen Verbindungen (einschließlich Aldehyden) von MEX-TRB/P-Prozessen fest, die häufig in nichtindustriellen Umgebungen wie Schulen, Wohnräumen und Büroräumen verwendet werden. Die Ergebnisse dieser Prüfverfahren entsprechen unter Umständen jedoch nicht genau den realen Bedingungen.
Dieses Dokument legt ein Konditionierungsverfahren unter Verwendung einer Emissionsprüfkammer mit Regelung von Temperatur, Luftfeuchte, Luftaustauschrate, Luftgeschwindigkeit sowie Verfahren zur Überwachung, Lagerung, Analyse, Berechnung und Angabe von Emissionsraten fest.
Dieses Dokument ist für MEX-TRB/P-Maschinen vorgesehen, die üblicherweise so groß sind, dass sie auf einem Schreibtisch stehen können, und in nichtindustriellen Umgebungen wie Schulen, Wohnräumen und Büroräumen verwendet werden. Der Hauptzweck dieses Dokuments ist die Quantifizierung der Partikel- und chemischen Emissionsraten von MEX-TRB/P-3D-Desktopdruckern.
Dieses Verfahren kann jedoch nicht alle möglichen Emissionen abdecken. Viele Ausgangsmaterialien können gefährliche Emissionen freisetzen, die nicht durch die in diesem Dokument beschriebenen chemischen Detektoren gemessen werden. Es liegt in der Verantwortung des Anwenders, das extrudierte Material und die möglichen chemischen Emissionen zu verstehen. Ein Beispiel sind Ausgangsmaterialien aus Polyvinylchlorid, die potentiell chlorierte Verbindungen emittieren können, die durch das in diesem Dokument beschriebene Verfahren nicht gemessen werden können.
Fabrication additive de plastiques - Environnement, santé et sécurité - Méthode d'essai pour la détermination des taux d'émission de particules et de produits chimiques des imprimantes 3D de bureau par extrusion de matériau (ISO 27548:2024)
Le présent document spécifie des méthodes d’essai pour déterminer les émissions de particules (y compris les particules ultrafines) et de composés organiques volatils spécifiques (y compris les aldéhydes) par les procédés MEX-TRB/P de bureau souvent employés dans des environnements non industriels, tels que les écoles, les foyers et les espaces de bureau, dans une chambre d’essai d’émission utilisée dans des conditions d’essai spécifiées. Toutefois, ces essais ne prédisent pas nécessairement avec précision les résultats qui seront réellement obtenus.
Le présent document spécifie une méthode de conditionnement utilisant une chambre d’essai d’émission avec une température, une humidité, un taux de renouvellement de l’air et une vitesse de l’air contrôlés, et des modes opératoires pour la surveillance, le stockage, l’analyse, le calcul et la consignation dans un rapport des taux d’émission.
Le présent document concerne les machines MEX-TRB/P de bureau qui sont généralement dimensionnées pour être placées sur un bureau et utilisées dans des lieux non industriels, tels que les écoles, les foyers et les espaces de bureau. Le but principal du présent document est de quantifier les taux d’émission de particules et de produits chimiques des machines MEX-TRB/P de bureau.
Toutefois, toutes les émissions possibles ne sont pas couvertes par cette méthode. De nombreuses matières premières peuvent libérer des émissions dangereuses qui ne sont pas mesurées par les détecteurs chimiques prescrits dans le présent document. Il relève de la responsabilité de l’utilisateur de connaître le matériau extrudé et les émissions chimiques potentielles. À titre d’exemple, le polychlorure de vinyle peut potentiellement émettre des composés chlorés qui ne peuvent pas être mesurés par la méthode décrite dans le présent document.
Dodajalna izdelava plastičnih izdelkov - Okolje, zdravje in varnost - Preskusna metoda za določanje stopnje emisije delcev in kemikalij iz namiznih 3D tiskalnikov za iztiskavanje materiala (ISO 27548:2024)
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
01-marec-2025
Dodajalna izdelava plastičnih izdelkov - Okolje, zdravje in varnost - Preskusna
metoda za določanje stopnje emisije delcev in kemikalij iz namiznih 3D tiskalnikov
za iztiskavanje materiala (ISO 27548:2024)
Additive manufacturing of plastics - Environment, health, and safety - Test method for
determination of particle and chemical emission rates from desktop material extrusion 3D
printer (ISO 27548:2024)
Additive Fertigung von Kunststoffen - Umwelt, Gesundheit und Sicherheit - Prüfverfahren
zur Bestimmung der Partikelemissionsrate und der chemischen Emissionsrate von
materialextrusionsbasierten Desktop-3D-Druckern (ISO 27548:2024)
Fabrication additive de plastiques - Environnement, santé et sécurité - Méthode d'essai
pour la détermination des taux d'émission de particules et de produits chimiques des
imprimantes 3D de bureau par extrusion de matériau (ISO 27548:2024)
Ta slovenski standard je istoveten z: EN ISO 27548:2024
ICS:
13.040.40 Emisije nepremičnih virov Stationary source emissions
13.100 Varnost pri delu. Industrijska Occupational safety.
higiena Industrial hygiene
25.030 3D-tiskanje Additive manufacturing
83.080.01 Polimerni materiali na Plastics in general
splošno
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 27548
EUROPEAN STANDARD
NORME EUROPÉENNE
July 2024
EUROPÄISCHE NORM
ICS 13.040.30; 13.100; 25.030
English Version
Additive manufacturing of plastics - Environment, health,
and safety - Test method for determination of particle and
chemical emission rates from desktop material extrusion
3D printer (ISO 27548:2024)
Fabrication additive de plastiques - Environnement, Additive Fertigung von Kunststoffen - Umwelt,
santé et sécurité - Méthode d'essai pour la Gesundheit und Sicherheit - Prüfverfahren zur
détermination des taux d'émission de particules et de Bestimmung der Partikelemissionsrate und der
produits chimiques des imprimantes 3D de bureau par chemischen Emissionsrate von
extrusion de matériau (ISO 27548:2024) materialextrusionsbasierten Desktop-3D-Druckern
(ISO 27548:2024)
This European Standard was approved by CEN on 6 July 2024.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 27548:2024 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 27548:2024) has been prepared by Technical Committee ISO/TC 261 "Additive
manufacturing" in collaboration with Technical Committee CEN/TC 438 “Additive Manufacturing” the
secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by January 2025, and conflicting national standards shall
be withdrawn at the latest by January 2025.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 27548:2024 has been approved by CEN as EN ISO 27548:2024 without any modification.
International
Standard
ISO 27548
First edition
Additive manufacturing of
2024-07
plastics — Environment, health,
and safety — Test method for
determination of particle and
chemical emission rates from
desktop material extrusion 3D
printer
Fabrication additive de plastiques — Environnement, santé
et sécurité — Méthode d'essai pour la détermination des
taux d'émission de particules et de produits chimiques des
imprimantes 3D de bureau par extrusion de matériau
Reference number
ISO 27548:2024(en) © ISO 2024
ISO 27548:2024(en)
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO 27548:2024(en)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Abbreviated terms and symbols . 4
4.1 Abbreviated terms .4
4.2 Symbols .4
5 Method overview . 5
6 Requirements of the instrument for measurement . 5
6.1 General .5
6.1.1 Emission test chamber (ETC) .5
6.1.2 Instruments for chemical analyses .5
6.1.3 Aerosol instruments .6
6.2 General requirements of desktop MEX-TRB/P machine and test specimen .6
6.2.1 Desktop MEX-TRB/P machine .6
6.2.2 Filament.6
6.2.3 Test specimen .7
7 ETC conditions and test procedures . 7
7.1 ETC general conditions .7
7.2 ETC background concentration .8
7.3 Preparation of ETC and desktop 3D printer .8
7.4 Pre-extruding phase . .9
7.5 Extruding phase .9
7.6 Post-extruding phase .9
7.7 Sampling for particles and chemical substances .9
7.7.1 Particles .9
7.7.2 Chemical substances .9
7.8 Measurement process .10
8 Calculation of emission rate .11
8.1 Calculation of emission rate of particles .11
8.2 Calculation of volatile organic compounds emission rate . 13
9 Test report . 14
9.1 Data on test condition and method .14
9.2 Data on filament and desktop 3D printer . 15
9.3 Description on standard test specimen .16
9.4 Information about test laboratory .16
9.5 Results . .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.