Small craft - Airborne sound emitted by powered recreational craft - Part 3: Sound assessment using calculation and measurement procedures (ISO 14509-3:2009)

This part of ISO 14509 specifies the procedures for assessing sound emission of powered monohull
recreational craft of length up to 24 m with a Froude number greater than 1,1. It is not applicable for personal
watercraft (PWC).
This part of ISO 14509 specifies the determination of the A-weighted sound pressure level by combining a
calculation method and a measurement method.

Kleine Wasserfahrzeuge - Von motorgetriebenen Sportbooten abgestrahlter Luftschall - Teil 3: Beurteilung der Schallemission mittels Rechen- und Messverfahren (ISO 14509-3:2009)

Dieser Teil von ISO 14509 legt ein Verfahren zur Beurteilung der Schallemission von motorgetriebenen, einrumpfigen Sportbooten einer Länge von bis zu 24 m mit einer Froude-Zahl größer als 1,1 fest. Er gilt nicht für Wassermotorräder (Jet-Ski).
Dieser Teil von ISO 14509 legt die Bestimmung des A-bewerteten Schalldruckpegels als Kombination eines Berechnungsverfahrens und eines Messverfahrens fest.

Petits navires - Bruit aérien émis par les bateaux de plaisance motorisés - Partie 3: Évaluation du bruit à l'aide de procédures de calcul et de mesure (ISO 14509-3:2009)

L'ISO 14509-3:2009 spécifie les procédures d'évaluation du bruit émis par les bateaux de plaisance monocoques motorisés de longueur de coque inférieure ou égale à 24 m, et dont le nombre de Froude est supérieur à 1,1. Elle n'est pas applicable aux motos aquatiques (VNM).
L'ISO 14509-3:2009 spécifie la détermination du niveau de pression acoustique pondéré A, en combinant une méthode de calcul et une méthode de mesure.

Mala plovila - Zvok v zraku, ki ga oddajajo motorizirana rekreacijska plovila - 3. del: Ocenjevanje hrupa z uporabo računskih in merilnih postopkov (ISO 14509-3:2009)

Ta del standarda ISO 14509 določa postopke za ocenjevanje zvočnih emisij motoriziranih rekreacijskih plovil z enim trupom dolžine 24 m s Froudovim številom več kot 1,1. Ne uporablja se za osebna plovila (PWC).
Ta del standarda ISO 14509 določa kombinirano uporabo računske metode in merilne metode za ugotavljanje A-vrednotene ravni zvočnega tlaka.

General Information

Status
Published
Public Enquiry End Date
14-Mar-2018
Publication Date
08-Oct-2018
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
05-Oct-2018
Due Date
10-Dec-2018
Completion Date
09-Oct-2018

Relations

Buy Standard

Standard
EN ISO 14509-3:2018
English language
20 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 14509-3:2018
01-december-2018
1DGRPHãþD
SIST EN ISO 14509-3:2009
0DODSORYLOD=YRNY]UDNXNLJDRGGDMDMRPRWRUL]LUDQDUHNUHDFLMVNDSORYLODGHO
2FHQMHYDQMHKUXSD]XSRUDERUDþXQVNLKLQPHULOQLKSRVWRSNRY ,62
Small craft - Airborne sound emitted by powered recreational craft - Part 3: Sound
assessment using calculation and measurement procedures (ISO 14509-3:2009)
Kleine Wasserfahrzeuge - Von motorgetriebenen Sportbooten abgestrahlter Luftschall -
Teil 3: Beurteilung der Schallemission mittels Rechen- und Messverfahren (ISO 14509-
3:2009)
Petits navires - Bruit aérien émis par les bateaux de plaisance motorisés - Partie 3:
Évaluation du bruit à l'aide de procédures de calcul et de mesure (ISO 14509-3:2009)
Ta slovenski standard je istoveten z: EN ISO 14509-3:2018
ICS:
17.140.30 Emisija hrupa transportnih Noise emitted by means of
sredstev transport
47.080 ýROQL Small craft
SIST EN ISO 14509-3:2018 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 14509-3:2018

---------------------- Page: 2 ----------------------

SIST EN ISO 14509-3:2018


EN ISO 14509-3
EUROPEAN STANDARD

NORME EUROPÉENNE

September 2018
EUROPÄISCHE NORM
ICS 47.080; 17.140.30 Supersedes EN ISO 14509-3:2009
English Version

Small craft - Airborne sound emitted by powered
recreational craft - Part 3: Sound assessment using
calculation and measurement procedures (ISO 14509-
3:2009)
Petits navires - Bruit aérien émis par les bateaux de Kleine Wasserfahrzeuge - Von motorgetriebenen
plaisance motorisés - Partie 3: Évaluation du bruit à Sportbooten abgestrahlter Luftschall - Teil 3:
l'aide de procédures de calcul et de mesure (ISO Beurteilung der Schallemission mittels Rechen- und
14509-3:2009) Messverfahren (ISO 14509-3:2009)
This European Standard was approved by CEN on 16 April 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2018 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 14509-3:2018 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 14509-3:2018
EN ISO 14509-3:2018 (E)
Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of Directive 2013/53/EU aimed to be covered . 4

2

---------------------- Page: 4 ----------------------

SIST EN ISO 14509-3:2018
EN ISO 14509-3:2018 (E)
European foreword
The text of ISO 14509-3:2009 has been prepared by Technical Committee ISO/TC 188 “Small craft” of the
International Organization for Standardization (ISO) and has been taken over as EN ISO 14509-3:2018.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by March 2019, and conflicting national standards shall be
withdrawn at the latest by March 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 14509-3:2009.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive 2013/53/EU.
For relationship with EU Directive 2013/53/EU, see informative Annex ZA, which is an integral part of
this document.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia,
Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands,
Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
the United Kingdom.
Endorsement notice
The text of ISO 14509-3:2009 has been approved by CEN as EN ISO 14509-3:2018 without any
modification.
3

---------------------- Page: 5 ----------------------

SIST EN ISO 14509-3:2018
EN ISO 14509-3:2018 (E)
Annex ZA
(informative)

Relationship between this European Standard and the Essential
Requirements of Directive 2013/53/EU aimed to be covered
This European standard has been prepared under a Commission’s standardization request M/542
C(2015) 8736 final to provide one voluntary means of conforming to Essential Requirements of Directive
2013/53/EU.
Once this standard is cited in the Official Journal of the European Union under that Directive, compliance
with the normative clauses of this standard given in Table ZA.1 confers, within the limits of the scope of
this standard, a presumption of conformity with the corresponding Essential Requirements of that
Directive and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and Annex I of Directive
2013/53/EU
Essential Clause(s)/sub- Remarks/Notes
Requirements of clause(s) of
Directive 2013/53/EU this EN
Annex I, Part C, 1 - Essential 4, 5, 6, This standard is applicable for powered mono hull craft
requirements for noise with a Froude number greater than 1.1; it is not applicable
Annex A,
emissions; Noise emission for personal watercraft (PWC).
Annex B
levels
Manufacturers and builders should be aware that the
assessment methodology use in this standard is based on
specific craft types and may be unsuitable for craft that
have characteristics that are significantly different from
those listed in the introduction to this standard.
This standard does not specify the information to be
provided in the Owner’s Manual in accordance with Annex
I.C.2
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.

4

---------------------- Page: 6 ----------------------

SIST EN ISO 14509-3:2018

INTERNATIONAL ISO
STANDARD 14509-3
First edition
2009-08-01

Small craft — Airborne sound emitted by
powered recreational craft —
Part 3:
Sound assessment using calculation and
measurement procedures
Petits navires — Bruit aérien émis par les bateaux de plaisance
motorisés —
Partie 3: Évaluation du bruit à l'aide de procédures de calcul et de
mesure




Reference number
ISO 14509-3:2009(E)
©
ISO 2009

---------------------- Page: 7 ----------------------

SIST EN ISO 14509-3:2018
ISO 14509-3:2009(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2009
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2009 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 14509-3:2018
ISO 14509-3:2009(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions. 2
4 Symbols . 2
5 Sound assessment method . 3
6 Test report . 3
Annex A (normative) Hull-form sound pressure level calculation. 4
Annex B (normative) On-board sound pressure level measurement method. 5
Annex C (informative) Example of test report form . 10

© ISO 2009 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 14509-3:2018
ISO 14509-3:2009(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 14509-3 was prepared by Technical Committee ISO/TC 188, Small craft.
ISO 14509 consists of the following parts, under the general title Small craft — Airborne sound emitted by
powered recreational craft:
⎯ Part 1: Pass-by measurement procedures
⎯ Part 2: Sound assessment using reference craft
⎯ Part 3: Sound assessment using calculation and measurement procedures

iv © ISO 2009 – All rights reserved

---------------------- Page: 10 ----------------------

SIST EN ISO 14509-3:2018
ISO 14509-3:2009(E)
Introduction
The European Union Directive 2003/44/EC (Amendment to Directive 94/25/EC) introduces limits for sound
emission from recreational craft and requires conformity for certain types of craft to be shown by using the
ISO 14509 series. ISO 14509-1 provides a practical measurement method, ISO 14509-2 provides an
assessment method using reference craft and this part of ISO 14509 provides a predictive measurement
method based on the work of the SoundBoat project. SoundBoat was funded by the European Commission
and various European Marine Industry Associations and industrial partners to develop alternative methods of
testing sound emission from recreational craft. Over the two years of the project, more than 65 craft have
been tested according to the ISO 14509-1 pass-by test. From this an algorithm has been developed that uses
a combination of hull–water sound, derived from hull parameters, and exhaust outlet sound, derived by direct
measurement on board the craft under test, to predict the sound pressure level that would be observed at
25 m had the craft undergone pass-by testing according to ISO 14509-1. The method specified in this part of
ISO 14509 does not require a measurement platform to be established and testing can be carried out
independently of location and weather restrictions. This method does not require a list of reference craft to be
established and provides a reproducible assessment procedure comparable to ISO 14509-1 pass-by testing to
within 2 dB.
The SoundBoat project has concentrated on specific craft types and has only tested craft with the following
characteristics:
⎯ bottom type configuration of not more than two chines;
⎯ square transom configuration;
⎯ length of hull 11 m or greater.
The SoundBoat project was successfully completed in early 2005, but industry continues to gather data from
on-water testing and, as the data model is refined with further validation of the concept, the parameters above
will be revised appropriately. The SoundBoat project team do not believe that craft outside the above
characteristics are unsuitable for assessment using this part of ISO 14509; however, where a significantly
different craft is to be assessed, it might be beneficial to test according to ISO 14509-1.

© ISO 2009 – All rights reserved v

---------------------- Page: 11 ----------------------

SIST EN ISO 14509-3:2018

-------------
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.