EN ISO 24817:2015
(Main)Petroleum, petrochemical and natural gas industries - Composite repairs for pipework - Qualification and design, installation, testing and inspection (ISO 24817:2015)
Petroleum, petrochemical and natural gas industries - Composite repairs for pipework - Qualification and design, installation, testing and inspection (ISO 24817:2015)
ISO 24817:2015 gives requirements and recommendations for the qualification and design, installation, testing, and inspection for the external application of composite repair systems to corroded or damaged pipework, pipelines, tanks, and vessels used in the petroleum, petrochemical, and natural gas industries.
Erdöl-, petrochemische und Erdgasindustrie - Reparatur von Rohrleitungen mit Verbundwerkstoffen - Bewertung und Ausführung, Montage, Test und Inspektion (ISO 24817:2015)
Industries du pétrole, de la pétrochimie et du gaz naturel - Réparations en matériau composite pour canalisations - Qualification et conception, installation, essai et inspection (ISO 24817:2015)
L'ISO 24817:2015 spécifie les exigences et les recommandations relatives à la qualification, la conception, l'installation, les essais et le contrôle lors de l'application externe de systèmes de réparation composites à des tuyauteries, conduites de transport, réservoirs et appareils à pression corrodés ou endommagés utilisés dans les industries du pétrole, de la pétrochimie et du gaz naturel.
Petrokemična industrija ter industrija za predelavo nafte in zemeljskega plina - Popravila cevovodov s kompozitnimi materiali - Ocenitev in načrtovanje, montaža, preskušanje in nadzor (ISO 24817:2015)
Ta mednarodni standard določa zahteve in priporočila za ocenitev in načrtovanje, montažo, preskušanje ter nadzor zunanje uporabe sistemov popravila s kompozitnimi materiali korodiranih ali poškodovanih cevovodov, cevovodnih sistemov, rezervoarjev in kotlov, ki se uporabljajo v industriji za predelavo nafte in zemeljskega plina ter petrokemični industriji.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2015
1DGRPHãþD
SIST-TS CEN ISO/TS 24817:2012
3HWURNHPLþQDLQGXVWULMDWHULQGXVWULMD]DSUHGHODYRQDIWHLQ]HPHOMVNHJDSOLQD
3RSUDYLODFHYRYRGRYVNRPSR]LWQLPLPDWHULDOL2FHQLWHYLQQDþUWRYDQMHPRQWDåD
SUHVNXãDQMHLQQDG]RU ,62
Petroleum, petrochemical and natural gas industries - Composite repairs for pipework -
Qualification and design, installation, testing and inspection (ISO 24817:2015)
Erdöl-, petrochemische und Erdgasindustrie - Reparatur von Rohrleitungen mit
Verbundwerkstoffen - Bewertung und Ausführung, Montage, Test und Inspektion (ISO
24817:2015)
Industries du pétrole, de la pétrochimie et du gaz naturel - Réparations en matériau
composite pour canalisations: Conformité aux exigences de performance et conception,
installation, essai et inspection (ISO 24817:2015)
Ta slovenski standard je istoveten z: EN ISO 24817:2015
ICS:
75.180.20 Predelovalna oprema Processing equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 24817
NORME EUROPÉENNE
EUROPÄISCHE NORM
August 2015
ICS 75.180.20 Supersedes CEN ISO/TS 24817:2011
English Version
Petroleum, petrochemical and natural gas industries - Composite
repairs for pipework - Qualification and design, installation,
testing and inspection (ISO 24817:2015)
Industries du pétrole, de la pétrochimie et du gaz naturel - Erdöl-, petrochemische und Erdgasindustrie - Reparatur
Réparations en matériau composite pour canalisations: von Rohrleitungen mit Verbundwerkstoffen - Bewertung und
Conformité aux exigences de performance et conception, Ausführung, Montage, Test und Inspektion (ISO
installation, essai et inspection (ISO 24817:2015) 24817:2015)
This European Standard was approved by CEN on 6 June 2015.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 24817:2015 E
worldwide for CEN national Members.
Contents Page
European foreword .3
European foreword
This document (EN ISO 24817:2015) has been prepared by Technical Committee ISO/TC 67 "Materials,
equipment and offshore structures for petroleum, petrochemical and natural gas industries" in collaboration
with Technical Committee CEN/TC 12 “Materials, equipment and offshore structures for petroleum,
petrochemical and natural gas industries” the secretariat of which is held by AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by February 2016, and conflicting national standards shall be withdrawn
at the latest by February 2016.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes CEN ISO/TS 24817:2011.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 24817:2015 has been approved by CEN as EN ISO 24817:2015 without any modification.
INTERNATIONAL ISO
STANDARD 24817
First edition
2015-08-01
Petroleum, petrochemical and natural
gas industries — Composite repairs for
pipework — Qualification and design,
installation, testing and inspection
Industries du pétrole, de la pétrochimie et du gaz naturel —
Réparations en matériau composite pour canalisations: Conformité aux
exigences de performance et conception, installation, essai et inspection
Reference number
ISO 24817:2015(E)
©
ISO 2015
ISO 24817:2015(E)
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved
ISO 24817:2015(E)
Contents Page
Foreword .v
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Symbols and abbreviated terms . 6
4.1 Symbols . 6
4.2 Abbreviated terms . 9
5 Applications . 9
6 Summary of key issues .11
7 Qualification and design .13
7.1 Repair feasibility assessment .13
7.2 Repair class .13
7.3 Repair design lifetime .14
7.4 Required data .15
7.4.1 Background.15
7.4.2 Original equipment design data .15
7.4.3 Maintenance and operational histories .15
7.4.4 Service condition data .15
7.4.5 Repair system qualification data.15
7.5 Design methodology.17
7.5.1 Overview .17
7.5.2 Environmental compatibility .19
7.5.3 Design temperature effects .19
7.5.4 Design based on substrate load sharing (defect type A) .21
7.5.5 Design based on repair laminate allowable strains (defect type A) .23
7.5.6 Design based on repair-allowable stresses determined by performance
testing (defect type A) .24
7.5.7 Design of repairs for through-wall defects (defect type B) .25
7.5.8 Axial extent of repair .28
7.5.9 Optional design considerations .29
7.5.10 Dent and/or gouge type defects .33
7.5.11 Fretting type defects .33
7.5.12 Delamination or blister type defects .33
7.5.13 Repair of other components .34
7.5.14 Design output .37
7.6 Re-qualification of the repair system .37
7.6.1 Overview .37
7.6.2 For type A defect repairs .37
7.6.3 For type B defect repairs .37
8 Installation .38
8.1 Storage conditions .38
8.2 Documentation prior to repair application .38
8.2.1 Method statement .38
8.2.2 Work pack .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.