EN ISO 3861:2021
(Main)Rubber hoses and hose assemblies for sand and grit blasting - Specification (ISO 3861:2021)
Rubber hoses and hose assemblies for sand and grit blasting - Specification (ISO 3861:2021)
This document specifies the requirements for rubber hoses and hose assemblies for wet and dry sand and grit blasting, suitable for use up to a maximum working pressure of 0,63 MPa (6,3 bar) and over an operating temperature range of −25 °C to +70 °C.
Gummischläuche und -schlauchleitungen zum Sandstrahlen - Spezifikation (ISO 3861:2021)
Dieses Dokument legt die Anforderungen an Gummischläuche und Schlauchleitungen zum Strahlen mit trockenem und nassem Sand und Kies fest, die für die Verwendung bis zu einem maximalen Betriebsdruck von 0,63 MPa (6,3 bar) und einem Betriebstemperaturbereich von −25 °C bis +70 °C geeignet sind.
Tuyaux et flexibles en caoutchouc pour sablage et grenaillage - Spécifications (ISO 3861:2021)
Le présent document spécifie les exigences pour les tuyaux et flexibles en caoutchouc destinés au sablage, sec et humide, et au grenaillage, pouvant être utilisés jusqu'à une pression maximale de service de 0,63 MPa (6,3 bar) et sur une plage de températures de service comprises de −25 °C à +70 °C.
Gumene cevi in cevni priključki za peskanje - Specifikacija (ISO 3861:2021)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-april-2021
Nadomešča:
SIST EN ISO 3861:2009
Gumene cevi in cevni priključki za peskanje - Specifikacija (ISO 3861:2021)
Rubber hoses and hose assemblies for sand and grit blasting - Specification (ISO
3861:2021)
Gummischläuche und -schlauchleitungen zum Sandstrahlen - Anforderungen (ISO
3861:2021)
Tuyaux et flexibles en caoutchouc pour sablage et grenaillage - Spécifications (ISO
3861:2021)
Ta slovenski standard je istoveten z: EN ISO 3861:2021
ICS:
83.140.40 Gumene cevi Hoses
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 3861
EUROPEAN STANDARD
NORME EUROPÉENNE
February 2021
EUROPÄISCHE NORM
ICS 25.220.10; 83.140.40 Supersedes EN ISO 3861:2008
English Version
Rubber hoses and hose assemblies for sand and grit
blasting - Specification (ISO 3861:2021)
Tuyaux et flexibles en caoutchouc pour sablage et Gummischläuche und -schlauchleitungen zum
grenaillage - Spécifications (ISO 3861:2021) Sandstrahlen - Anforderungen (ISO 3861:2021)
This European Standard was approved by CEN on 4 January 2021.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 3861:2021 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 3861:2021) has been prepared by Technical Committee ISO/TC 45 "Rubber and
rubber products" in collaboration with Technical Committee CEN/TC 218 “Rubber and plastics hoses
and hose assemblies” the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by August 2021, and conflicting national standards shall
be withdrawn at the latest by August 2021.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 3861:2008.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 3861:2021 has been approved by CEN as EN ISO 3861:2021 without any modification.
INTERNATIONAL ISO
STANDARD 3861
Fourth edition
2021-01
Rubber hoses and hose assemblies for
sand and grit blasting — Specification
Tuyaux et flexibles en caoutchouc pour sablage et grenaillage —
Spécifications
Reference number
ISO 3861:2021(E)
©
ISO 2021
ISO 3861:2021(E)
© ISO 2021
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2021 – All rights reserved
ISO 3861:2021(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Classification . 2
5 Materials and construction . 2
6 Dimensions . 2
6.1 Inside diameter and tolerances . 2
6.2 Concentricity. 3
6.3 Tolerance on length . 3
6.4 Minimum thickness of lining and cover . 3
7 Physical properties . 3
7.1 Rubber compounds . 3
7.2 Finished hoses and hose assemblies . 3
8 Frequency of testing . 4
9 Marking . 4
9.1 Hoses . 4
9.2 Hose assemblies . 5
Annex A (normative) Test frequency for type tests and routine tests . 6
Annex B (informative) Production acceptance tests . 7
ISO 3861:2021(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 45, Rubber and rubber products,
Subcommittee SC 1, Rubber and plastics hoses and hose assemblies, in collaboration with the European
Committee for Standardization (CEN) Technical Committee CEN/TC 218 Rubber and plastics hoses and
hose assemblies, in accordance with the Agreement on technical cooperation between ISO and CEN
(Vienna Agreement).
This fourth edition cancels and replaces the third edition (ISO 3861:2005), which has been technically
revised. The main changes compared to the previous edition are as follows:
— MPa units have been added throughout the document;
— Clause 2 has been updated;
— inside diameters of 20 mm and 40 mm have been deleted;
— Clause 8 on frequency of testing, and Annexes A and B have been added;
— Clause 9 on marking has been updated.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
iv © ISO 2021 – All rights reserved
ISO 3861:2021(E)
Introduction
This document specifies rubber hoses for sand and grit blasting. When hoses are fitted with couplings,
the document also contains requirements for hose assemblies.
INTERNATIONAL STANDARD ISO 3861:2021(E)
Rubber hoses and hose assemblies for sand and grit
blasting — Specification
WARNING — Persons using this document should be familiar with normal laboratory practice.
This document does not purport to address all the safety problems, if any, associated with its
use. It is the responsibility of the user to establish appropriate health and safety practices and to
ensure compliance with any national regulatory conditions.
1 Scope
This document specifies the requirements for rubber hoses and hose assemblies for wet and dry sand
and grit blasting, suitable for use up to a maximum working pressure of 0,63 MPa (6,3 bar) and over an
operating temperature range of −25 °C to +70 °C.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 37, Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties
ISO 188:2011, Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests
ISO
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.