EN ISO 22825:2017

Non-destructive testing of welds - Ultrasonic testing - Testing of welds in austenitic steels and nickel-based alloys (ISO 22825:2017)

ISO 22825:2017 specifies the approach to be followed when developing procedures for the ultrasonic testing of the following welds:
-      welds in stainless steels;
-      welds in nickel-based alloys;
-      welds in duplex steels;
-      dissimilar metal welds;
-      austenitic welds.
The purposes of the testing can be very different, for example:
-      for the assessment of quality level (manufacturing);
-      for the detection of specific discontinuities induced in service.
Acceptance levels are not included in ISO 22825:2017, but can be applied in accordance with the scope of the testing (see 4.1).
The requirements of ISO 22825:2017 are applicable to both manual and mechanized testing.

Zerstörungsfreie Prüfung von Schweißverbindungen - Ultraschallprüfung - Prüfung von Schweißverbindungen in austenitischen Stählen und Nickellegierungen (ISO 22825:2017)

Essais non destructifs des assemblages soudés - Contrôle par ultrasons - Contrôle des soudures en aciers austénitiques et en alliages à base nickel (ISO 22825:2017)

L'ISO 22825:2017 spécifie l'approche à suivre pour la mise au point des modes opératoires de contrôle par ultrasons des soudures suivantes:
-      soudures sur aciers inoxydables;
-      soudures sur alliages à base de nickel;
-      soudures sur aciers duplex;
-      soudures sur métaux dissemblables;
-      soudures sur aciers austénitiques.
Les objectifs des essais peuvent être très différents, par exemple:
-      évaluation du niveau de qualité (fabrication);
-      détection de discontinuités spécifiques produites au cours du service.
Les niveaux d'acceptation ne sont pas inclus dans l'ISO 22825:2017, mais ils peuvent être appliqués selon le domaine d'application des essais (voir 4.1).
Les exigences de l'ISO 22825:2017 sont applicables à la fois au contrôle manuel et au contrôle mécanisé.

Neporušitveno preskušanje zvarnih spojev - Ultrazvočno preskušanje - Preskušanje zvarnih spojev iz avstenitnih jekel in nikljevih zlitin (ISO 22825:2017)

Ta dokument določa pristop k razvoju postopkov za ultrazvočno preskušanje naslednjih zvarnih spojev:
– zvarni spoji iz nerjavnega jekla;
– zvarni spoji iz nikljevih litin;
– zvarni spoji iz dvojnega jekla;
– zvarni spoji iz različnih kovin;
– avstenitni zvarni spoji.
Nameni preskušanja so lahko zelo različni, na primer:
– vrednotenje ravni kakovosti (proizvodnje);
– ugotavljanje posebnih nehomogenosti, ki se pojavijo pri uporabi.
Ta dokument ne zajema stopenj spremenljivosti, vendar se lahko te uporabijo v skladu s področjem uporabe preskušanja (glej točko 4.1).
Zahteve iz tega dokumenta se uporabljajo za ročno in mehansko preskušanje.

General Information

• Status: Published
• Publication Date: 31-Oct-2017
• Withdrawal Date: 30-May-2018
• ICS: 25.160.40 - Welded joints and welds
• Technical Committee: CEN/TC 121 - Welding
• Drafting Committee: CEN/TC 121/WG 21 - Testing of welds
• Current Stage: 6060 - Definitive text made available (DAV) - Publishing
• Start Date: 01-Nov-2017
• Completion Date: 01-Nov-2017
• Ref Project: SIST EN ISO 22825:2018 - Non-destructive testing of welds - Ultrasonic testing - Testing of welds in austenitic steels and nickel-based alloys (ISO 22825:2017)

Relations

• Replaces: EN ISO 22825:2012 - Non-destructive testing of welds - Ultrasonic testing - Testing of welds in austenitic steels and nickel-based alloys (ISO 22825:2012)
• Effective Date: 08-Nov-2017

Standards Content (Sample)

SLOVENSKI STANDARD
01-marec-2018
1DGRPHãþD
SIST EN ISO 22825:2012
1HSRUXãLWYHQRSUHVNXãDQMH]YDUQLKVSRMHY8OWUD]YRþQRSUHVNXãDQMH
3UHVNXãDQMH]YDUQLKVSRMHYL]DYVWHQLWQLKMHNHOLQQLNOMHYLK]OLWLQ,62
Non-destructive testing of welds - Ultrasonic testing - Testing of welds in austenitic steels
and nickel-based alloys (ISO 22825:2017)
Zerstörungsfreie Prüfung von Schweißverbindungen - Ultraschallprüfung - Prüfung von
Schweißverbindungen in austenitischen Stählen und Nickellegierungen (ISO
22825:2017)
Contrôle non destructif des assemblages soudés - Contrôle par ultrasons - Contrôle des
soudures en aciers austénitiques et en alliages à base nickel (ISO 22825:2017)
Ta slovenski standard je istoveten z: EN ISO 22825:2017
ICS:
25.160.40 Varjeni spoji in vari Welded joints and welds
77.080.20 Jekla Steels
77.120.40 Nikelj, krom in njune zlitine Nickel, chromium and their
alloys
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 22825
EUROPEAN STANDARD
NORME EUROPÉENNE
November 2017
EUROPÄISCHE NORM
ICS 25.160.40 Supersedes EN ISO 22825:2012
English Version
Non-destructive testing of welds - Ultrasonic testing -
Testing of welds in austenitic steels and nickel-based
alloys (ISO 22825:2017)
Essais non destructif des assemblages soudés - Zerstörungsfreie Prüfung von Schweißverbindungen -
Contrôle par ultrasons - Contrôle des soudures en Ultraschallprüfung - Prüfung von
aciers austénitiques et en alliages à base nickel (ISO Schweißverbindungen in austenitischen Stählen und
22825:2017) Nickellegierungen (ISO 22825:2017)
This European Standard was approved by CEN on 26 August 2017.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 22825:2017 E
worldwide for CEN national Members.

Contents Page
European foreword . 3

European foreword
This document (EN ISO 22825:2017) has been prepared by Technical Committee ISO/TC 44 “Welding
and allied processes” in collaboration with Technical Committee CEN/TC 121 “Welding and allied
processes” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by May 2018 and conflicting national standards shall be
withdrawn at the latest by May 2018.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 22825:2012.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 22825:2017 has been approved by CEN as EN ISO 22825:2017 without any modification.
INTERNATIONAL ISO
STANDARD 22825
Third edition
2017-09
Non-destructive testing of welds —
Ultrasonic testing — Testing of welds
in austenitic steels and nickel-based
alloys
Essais non destructifs des assemblages soudés — Contrôle par
ultrasons — Contrôle des soudures en aciers austénitiques et en
alliages à base nickel
Reference number
ISO 22825:2017(E)
©
ISO 2017
ISO 22825:2017(E)
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. [phone]
Fax [phone]
[e-mail]
www.iso.org
ii © ISO 2017 – All rights reserved

ISO 22825:2017(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Information required prior to testing . 2
4.1 Items to be defined by specification . 2
4.2 Specific information required by the operator prior to testing . 2
5 Personnel . 3
6 Test equipment. 3
6.1 Conventional equipment . 3
6.2 Phased array equipment. 3
7 Range setting for compression waves . 3
8 Sensitivity setting . 4
8.1 General . 4
8.2 Use of side-drilled holes . 5
8.3 Use of other reference reflectors . 5
9 Test procedure and ultrasonic techniques . 5
9.1 Development of the test procedure . 5
9.2 Content of the test procedure . 5
9.3 Selection of ultrasonic technique(s) . 7
9.4 Optimization of test technique and draft of test procedure . 8
9.5 Practical implications of the use of refracted compression waves . 8
10 Classification and sizing of indications . 9
11 Testing of welds . 9
11.1 General . 9
11.2 Surface condition and couplant fluid . 9
11.3 Parent metal testing . 9
11.4 Scanning . 9
11.5 Evaluation of indications .10
12 Test report .10
12.1 General data .10
12.2 Information related to the test equipment .10
12.3 Information related to the testing technique.11
12.4 Results of testing .11
Annex A (informative) Compression wave angle-beam techniques .12
Annex B (informative) Stainless steel calibration blocks for range setting .18
Annex C (informative) Reference blocks for sensitivity setting .20
Bibliography .23
ISO 22825:2017(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1
...