EN ISO 780:2015
(Main)Packaging - Distribution packaging - Graphical symbols for handling and storage of packages (ISO 780:2015)
Packaging - Distribution packaging - Graphical symbols for handling and storage of packages (ISO 780:2015)
ISO 780:2015 specifies a set of graphical symbols conventionally used for marking of distribution packages in their physical distribution chain to convey handling instructions. The graphical symbols should be used only when necessary.
ISO 780:2015 is applicable to packages containing any kind of goods, but does not include instructions specific to handling of dangerous goods.
Verpackung - Versandverpackung - Graphische Symbole für die Handhabung und Lagerung von Packstücken (ISO 780:2015)
Diese Internationale Norm legt eine Reihe von graphischen Symbolen fest, die üblicherweise für die Markierung von Versandverpackungen bei der physischen Warenverteilung benutzt werden, um Anweisungen für die Handhabung zu geben. Die graphischen Symbole sollten nur benutzt werden, wenn dies erforderlich ist.
Diese Internationale Norm gilt für Verpackungen, die Güter jeglicher Art enthalten, aber sie beinhaltet keine speziellen Anweisungen für die Handhabung von gefährlichen Gütern.
Emballages - Emballages de distribution - Symboles graphiques pour la manutention et le stockage des emballages (ISO 780:2015)
ISO 780:2015 spécifie un ensemble de symboles graphiques utilisés d'une manière conventionnelle pour le marquage des emballages de distribution au cours de leur chaîne de distribution physique afin de transmettre les instructions de manutention. Il convient d'utiliser les symboles graphiques seulement lorsqu'ils s'avèrent nécessaires.
ISO 780:2015 est applicable à des emballages contenant des marchandises de tout genre, mais ne couvre pas les instructions de manutention spécifiques aux marchandises dangereuses.
Embalaža - Embalaža za distribucijo - Grafični simboli za hranjenje embalaže in ravnanje z njo (ISO 780:2015)
Ta mednarodni standard določa nabor grafičnih simbolov, ki se po dogovoru uporabljajo za označevanje distribucijskih paketov v njihovi fizični distribucijski verigi za izražanje navodil za uporabo. Grafični
simboli naj bi se uporabljali le po potrebi.
Ta mednarodni standard velja za pakete, ki vsebujejo kakršno koli vrsto blaga, vendar ne vključuje
navodil, namenjenih posebej za ravnanje z nevarnim blagom.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-februar-2016
1DGRPHãþD
SIST EN ISO 780:2000
(PEDODåD(PEDODåD]DGLVWULEXFLMR*UDILþQLVLPEROL]DKUDQMHQMHHPEDODåHLQ
UDYQDQMH]QMR ,62
Packaging - Distribution packaging - Graphical symbols for handling and storage of
packages (ISO 780:2015)
Verpackung - Versandverpackung - Graphische Symbole für die Handhabung und
Lagerung von Packstücken (ISO 780:2015)
Emballages - Emballages de distribution - Symboles graphiques pour la manutention et
le stockage des emballages (ISO 780:2015)
Ta slovenski standard je istoveten z: EN ISO 780:2015
ICS:
01.080.20 *UDILþQLVLPEROL]DSRVHEQR Graphical symbols for use on
RSUHPR specific equipment
55.020 Pakiranje in distribucija blaga Packaging and distribution of
na splošno goods in general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 780
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2015
EUROPÄISCHE NORM
ICS 55.020; 01.080.99 Supersedes EN ISO 780:1999
English Version
Packaging - Distribution packaging - Graphical symbols for
handling and storage of packages (ISO 780:2015)
Emballages - Emballages de distribution - Symboles Verpackung - Versandverpackung - Graphische
graphiques pour la manutention et le stockage des Symbole für die Handhabung und Lagerung von
emballages (ISO 780:2015) Packstücken (ISO 780:2015)
This European Standard was approved by CEN on 20 November 2015.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2015 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 780:2015 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 780:2015) has been prepared by Technical Committee ISO/TC 122 "Packaging"
in collaboration with Technical Committee CEN/TC 261 “Packaging” the secretariat of which is held by
AFNOR.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2016, and conflicting national standards shall be
withdrawn at the latest by June 2016.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent
rights.
This document supersedes EN ISO 780:1999.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 780:2015 has been approved by CEN as EN ISO 780:2015 without any modification.
INTERNATIONAL ISO
STANDARD 780
Fifth edition
2015-12-01
Packaging — Distribution packaging
— Graphical symbols for handling and
storage of packages
Emballages — Emballages de distribution — Symboles graphiques
pour la manutention et le stockage des emballages
Reference number
ISO 780:2015(E)
©
ISO 2015
ISO 780:2015(E)
© ISO 2015, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2015 – All rights reserved
ISO 780:2015(E)
Contents Page
Foreword .iv
Introduction .vi
1 Scope . 1
2 Normative references . 1
3 Graphical Symbols . 1
3.1 General . 1
3.2 Display of graphical symbols . 1
3.3 Colour of graphical symbols . 1
3.4 Size of graphical symbols . 2
3.5 Number of graphical symbols . 2
3.6 Position of graphical symbols . 2
4 Meaning and requirements of the graphical symbols . 2
4.1 General . 2
4.2 Graphical symbols used for large-sized packages . 2
4.3 Graphical symbols used for middle and small-sized packages . 2
4.4 Graphical symbols used for both transport and storage . 2
4.5 Graphical symbols used for storage . 2
Bibliography . 9
ISO 780:2015(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2. www.iso.org/directives
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received. www.iso.org/patents
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the meaning of ISO specific terms and expressions related to conformity
assessment, as well as information about ISO’s adherence to the WTO principles in the Technical
Barriers to Trade (TBT), see the following URL: Foreword - Supplementary information
The committee responsible for this document is ISO/TC 122, Packaging.
This fifth edition cancels and replaces the fourth edition (ISO 780:1997), which has been technically
revised.
All the 17 graphical symbols in this International Standard have already been modified to accord with
IEC 80416-1:2008, Basic principles for graphical symbols for use on equipment — Part 1: Creation of
graphical symbols for registration and submitted to TC 145/SC 3 for registration on ISO 7000, Graphical
symbols for use on equipment — Registered symbols.
Some of the major modification points are indicated as follows:
a) Title:
New: Packaging – Distribution packaging – Graphical symbols for handling and storage of packages
Old: Packaging – Pictorial marking for handling of goods
“Distribution packaging” is preferred to “transport packaging” in this standard. The reason is that
“transport packaging” does not include “stored” packages, for example, in the practice of “transport
packaging for dangerous goods”. ISO 780 concerns with packages during storage as well as those
during transport.
“Pictorial marking” is replaced by “graphical symbols” to coincide with TC 145’s way of addressing
pictorial marking.
b) Introduction:
Statements on safety issue and hand-written symbols have been added.
c) Handling instructions:
The order of the graphical symbols has been re-arranged in the following order.
1) Graphical symbols used for large-sized packages.
iv © ISO 2015 – All rights reserved
ISO 780:2015(E)
2) Graphical symbols used for middle and small-sized packages:
— For all types of handling;
— For manual handling;
— For handling using machines.
3) Graphical symbols used for both transport and storage.
4) Graphical symbols used for storage.
To make this standard easier to use, the layout of the table has been changed and each graphical symbol
has its Reference No. to ISO 7000, Meaning, Requirement, Note and example of application.
ISO 780:2015(E)
Introduction
Packages are often marked with handling instructions in the language of the country of origin. While
this may safeguard the consignment in the areas using the same language, it is of little value for goods
consigned to, or through, countries using different languages, and of no value at all if people handling
the packages are illiterate.
Graphical symbols offer the best possibility of conveying the consignor’s intention and their adoption
will; therefore, undoubtedly reduce loss and damage through incorrect handling. Moreover, graphical
symbols help ensure safety of workers, who cannot grasp such important information as structure,
gravity centre, property, and strength of a package while handling distribution packages.
The graphical symbols specified are in accordance with the rules of ISO/TC 145/SC 3, Graphical symbols
for use on equipment.
The use of graphical symbols does not provide any guarantee of satisfactory handling; safely and
properly protective packaging is therefore of primary importance.
Distribution packages could deteriorate as time passes and sometimes cannot withstand normal
handling before they reach the final desti
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.