EN ISO 694:2001
(Main)Ships and marine technology - Positioning of magnetic compasses in ships (ISO 694:2000)
Ships and marine technology - Positioning of magnetic compasses in ships (ISO 694:2000)
2009-05-25 SJ: Std withdrawn following publication in ISO of ISO 25862 (see resolution BT65/2007).
Schiffe und Meerestechnik - Aufstellung von Magnetkompassen auf Schiffen (ISO 694:2000)
Anwendungsbereich
Diese Internationale Norm spezifiziert die Aufstellung von Magnetkompassen und Kompass-ständen, die den Anforderungen von ISO 449, ISO 613, ISO 2269 und ISO 10316 entsprechen, an Bord von Schiffen.
Außerdem deckt sie Magnetsensoren ab, die in Navigationshilfsmitteln verwendet werden.
Es muss beachtet werden, dass diese Internationale Norm nur für allgemeine Zwecke aufgestellt wurde. Sie ist nicht notwendigerweise auf alle Seeschiffe anwendbar.
Navires et technologie maritime - Emplacement des compas magnétiques à bord des navires (ISO 694:2000)
Ships and marine technology - Positioning of magnetic compasses in ships (ISO 694:2000)
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 694:2002
01-januar-2002
Ships and marine technology - Positioning of magnetic compasses in ships (ISO
694:2000)
Ships and marine technology - Positioning of magnetic compasses in ships (ISO
694:2000)
Schiffe und Meerestechnik - Aufstellung von Magnetkompassen auf Schiffen (ISO
694:2000)
Navires et technologie maritime - Emplacement des compas magnétiques a bord des
navires (ISO 694:2000)
Ta slovenski standard je istoveten z: EN ISO 694:2001
ICS:
47.020.70 Navigacijska in krmilna Navigation and control
oprema equipment
SIST EN ISO 694:2002 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 694:2002
---------------------- Page: 2 ----------------------
SIST EN ISO 694:2002
EUROPEAN STANDARD
EN ISO 694
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2001
ICS 47.020.70
English version
Ships and marine technology - Positioning of magnetic
compasses in ships (ISO 694:2000)
Navires et technologie maritime - Emplacement des Schiffe und Meerestechnik - Aufstellung von
compas magnétiques à bord des navires (ISO 694:2000) Magnetkompassen auf Schiffen (ISO 694:2000)
This European Standard was approved by CEN on 9 June 2001.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2001 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 694:2001 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 694:2002
EN ISO 694:2001 (E)
CORRECTED 2001-09-19
Foreword
The text of the International Standard from Technical Committee ISO/TC 8 "Ships and marine
technology" of the International Organization for Standardization (ISO) has been taken over
as an European Standard by Technical Committee CEN/TC 300 "Sea-going vessels and
marine technology", the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication
of an identical text or by endorsement, at the latest by January 2002, and conflicting national
standards shall be withdrawn at the latest by January 2002.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy,
Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United
Kingdom.
Endorsement notice
The text of the International Standard ISO 694:2000 has been approved by CEN as a
European Standard without any modification.
NOTE Normative references to International Standards are listed in annex ZA (normative).
2
---------------------- Page: 4 ----------------------
SIST EN ISO 694:2002
EN ISO 694:2001 (E)
Annex ZA
(normative)
Normative references to International Publicationswith their relevant
European publications
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text, and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions
of any of these publications apply to this European Standard only when incorporated in it by
amendment or revision. For undated references the latest edition of the publication referred to
applies (including amendments).
NOTE Where an International Publication has been modified by common modifications,
indicated by (mod.), the relevant EN/HP applies.
Publication Year Title EN/HD Year
ISO 449 1997 Ships and marine technology - Magnetic EN ISO 449 1999
compasses, binnacles and azimuth reading
devices - Class A
3
---------------------- Page: 5 ----------------------
SIST EN ISO 694:2002
---------------------- Page: 6 ----------------------
SIST EN ISO 694:2002
INTERNATIONAL ISO
STANDARD 694
First edition
2000-02-01
Ships and marine technology —
Positioning of magnetic compasses in
ships
Navires et technologie maritime — Emplacement des compas magnétiques
à bord des navires
Reference number
ISO 694:2000(E)
©
ISO 2000
---------------------- Page: 7 ----------------------
SIST EN ISO 694:2002
ISO 694:2000(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2000
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 734 10 79
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 2000 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 694:2002
ISO 694:2000(E)
Contents Page
Foreword.iv
Introduction.v
1 Scope .1
2 Normative references .1
3 Terms and definitions .1
4 General.3
5 Minimum distance requirements concerning the ship’s structure .3
6 Safe-distance requirements for magnetic and electrical equipment and electric cables.4
Annex A (normative) Determination of safe distances .6
© ISO 2000 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 694:2002
ISO 694:2000(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 694 was prepared by Technical Committee ISO/TC 8, Ships and marine technology,
Subcommittee SC 6, Navigation.
This first edition of ISO 694 cancels and replaces ISO Recommendation ISO/R 694:1968. In this International
Standard only one method for the determination of safe distances is prescribed instead of the two methods in the
Recommendation. Some values of minimum distances from the ship’s iron have been changed.
Annex A forms a normative part of this International Standard.
iv © ISO 2000 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 694:2002
ISO 694:2000(E)
Introduction
The following elements produce magnetic fields which act on the magnetic compass and cause errors (deviations):
the steel parts of the ship’s construction, electric currents, electric and magnetic equipment of the ship which is
installed in the vicinity of the magnetic compass, such as radar, echo sounder, etc.
To minimize these errors, the distances of the sources of magnetic disturbant fields from the magnetic compass
should be as large as possible. This International Standard defines and prescribes the minimum distances to be
respected.
Moreover, the method for determination of safe distances of electric and magnetic equipment from the magnetic
compass is described.
In order to obtain satisfactory and durable compensation of compasses, this International Standard should be taken
into consideration during the design stage of a ship.
© ISO 2000 – All rights reserved v
---------------------- Page: 11 ----------------------
SIST EN ISO 694:2002
---------------------- Page: 12 ----------------------
SIST EN ISO 694:2002
INTERNATIONAL STANDARD ISO 694:2000(E)
Ships and marine technology — Positioning of magnetic
compasses in ships
1 Scope
This International Standard specifies the installation in ships of magnetic compasses and binnacles complying with
the requirements of ISO 449, ISO 613, ISO 2269 and ISO 10316.
In addition, it covers magnetic control elements used in navigational aids.
It should be noted that this International Standard is established only for general purposes. It is not necessarily
applicable to all sea-going ships.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this International Standard. For dated references, subsequent amendments to, or revisions of, these publications
do not apply. However, parties to agreements based on this International Standard are en
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.