EN ISO 10439:2002
(Main)Petroleum, chemical and gas service industries - Centrifugal compressors (ISO 10439:2002)
Petroleum, chemical and gas service industries - Centrifugal compressors (ISO 10439:2002)
ISO 10439 specifies requirements and gives recommendations for the design, materials, fabrication, inspection, testing and preparation for shipment of centrifugal compressors for use in the petroleum, chemical and gas service industries. It is not applicable to machines that develop less than 35 kPa above atmospheric pressure, nor is it applicable to packaged, integrally geared centrifugal air compressors, which are covered in ISO 10442.
Erdöl-, Chemie- und Erdgasindustrie - Radial-Turbokompressoren (ISO 10439:2002)
In dieser Internationalen Norm werden Anforderungen an und Empfehlungen für Konstruktion, Werkstoffe, Fertigung, Inspektion, Prüfung und Versandvorbereitungen von Turbokompressoren festgelegt, die in der Öl- und
Gasindustrie sowie in der chemischen Industrie eingesetzt werden. Diese Internationale Norm gilt nicht für Arbeitsmaschinen, die den Druck auf einen Wert erhöhen, der weniger als 35 kPa über dem atmosphärischen Druck liegt. Sie gilt ferner nicht für Turbo-Luftkompressoranlagen mit integriertem Getriebe, die in ISO 10442 behandelt werden.
ANMERKUNG Wenn möglich, werden in dieser Internationalen Norm die im US-Sprachraum gebräuchlichen Einheiten in Klammern angegeben.
Industries du pétrole, de la chimie et du gaz - Compresseurs centrifuges (ISO 10439:2002)
L'ISO 10439 spécifie les exigences et fournit des recommandations pour la conception, les matériaux, la fabrication, le contrôle, les essais et la préparation pour l'expédition des compresseurs centrifuges utilisés dans les industries du pétrole, de la chimie et du gaz. Elle n'est pas applicable aux machines qui développent moins de 35 kPa au-dessus de la pression atmosphérique. Elle n'est pas applicable non plus à des unités de compresseurs centrifuges à engrenages, qui sont couverts par l'ISO 10442.
Petroleum, chemical and gas service industries - Centrifugal compressors (ISO 10439:2002)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-maj-2004
Petroleum, chemical and gas service industries - Centrifugal compressors (ISO
10439:2002)
Petroleum, chemical and gas service industries - Centrifugal compressors (ISO
10439:2002)
Erdöl-, Chemie- und Erdgasindustrie - Radial-Turbokompressoren (ISO 10439:2002)
Industries du pétrole, de la chimie et du gaz - Compresseurs centrifuges (ISO
10439:2002)
Ta slovenski standard je istoveten z: EN ISO 10439:2002
ICS:
23.140 .RPSUHVRUMLLQSQHYPDWLþQL Compressors and pneumatic
VWURML machines
75.180.20 Predelovalna oprema Processing equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
INTERNATIONAL ISO
STANDARD 10439
First edition
2002-10-15
Corrected version
2003-06-15
Petroleum, chemical and gas service
industries — Centrifugal compressors
Industries du pétrole, de la chimie et du gaz — Compresseurs centrifuges
Reference number
ISO 10439:2002(E)
©
ISO 2002
ISO 10439:2002(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2002
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Printed in Switzerland
ii © ISO 2002 – All rights reserved
ISO 10439:2002(E)
Contents Page
Foreword . v
Introduction. vi
1 Scope. 1
2 Normative references. 1
3 Terms and definitions. 2
4 Basic design . 4
4.1 General . 4
4.2 Casings. 7
4.3 Interstage diaphragms and inlet guide vanes. 8
4.4 Casing connections . 9
4.5 External forces and moments. 10
4.6 Rotating elements . 10
4.7 Bearings and bearing housings . 11
4.8 Shaft seals . 14
4.9 Dynamics . 22
4.10 “Lube” oil and seal oil systems. 29
4.11 Materials. 29
4.12 Nameplates and rotation arrows . 32
5 Accessories . 33
5.1 Drivers . 33
5.2 Couplings and guards . 34
5.3 Mounting plates. 34
5.4 Controls and instrumentation. 36
5.5 Piping and appurtenances . 41
5.6 Special tools . 42
6 Inspection, testing and preparation for shipment . 42
6.1 General . 42
6.2 Inspection . 43
6.3 Testing. 44
6.4 Preparation for shipment. 49
7 Vendor data. 50
7.1 General . 50
7.2 Proposals . 51
7.3 Contract data . 54
Annex A (informative) Typical data sheets . 56
Annex B (informative) Material specifications for major component parts. 81
Annex C (normative) Centrifugal compressor vendor drawing and data requirements. 86
Annex D (normative) Procedure for determination of residual unbalance. 95
Annex E (informative) Rotor dynamic logic diagrams . 102
Annex F (informative) Centrifugal compressor nomenclature. 106
Annex G (normative) Forces and moments. 107
Annex H (informative) Inspector's checklist . 110
Annex I (informative) Typical gas seal testing considerations. 112
ISO 10439:2002(E)
Annex J (informative) Application considerations for active magnetic bearings. 114
Bibliography. 117
iv © ISO 2002 – All rights reserved
ISO 10439:2002(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
The main task of technical committees is to prepare International Standards. Draft International Standards adopted
by the technical committees are circulated to the member bodies for voting. Publication as an International
Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this International Standard may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 10439 was prepared by a Joint Working Group of Technical Committees ISO/TC 118, Compressors,
pneumatic tools and pneumatic machines, and ISO/TC 67, Materials, equipment and offshore structures for
petroleum, petrochemical and natural gas industries, Subcommittee SC 6, Processing equipment and systems.
Annexes C, D and G form a normative part of this International Standard. Annexes A, B, E, F, H, I and J are for
information only.
In this corrected version of ISO 10439 an oversight which saw the words “Final Draft” and its abbreviation left in the
header of page 1 has been corrected.
ISO 10439:2002(E)
Introduction
This International Standard is based on the sixth edition of the American Petroleum Institute standard API 617.
Users of this International Standard should be aware that further or differing requirements may be needed for
individual applications. This International Standard is not intended to inhibit a vendor from offering, or the purchaser
from accepting, alternative equipment or engineering solutions for the individual application. This may be
particularly applicable where there is innovative or developing technology. Where an alternative is offered, the
vendor should identify any variations from this International Standard and provide details.
vi © ISO 2002 – All rights reserved
INTERNATIONAL STANDARD ISO 10439:2002(E)
Petroleum, chemical and gas service industries — Centrifugal
compressors
1 Scope
This International Standard specifies requirements and gives recommendations for the design, materials,
fabrication, inspection, testing and preparation for shipment of centrifugal compressors for use in the petroleum,
chemical and gas service industries. It is not applicable to machines that develop less than 35 kPa above
atmospheric pressure, nor is it applicable to packaged, integrally geared centrifugal air compressors, which are
covered in ISO 10442.
NOTE In this International Standard, where practical, US customary units have been included in brackets for information.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this International Standard. For dated references, subsequent amendments to, or revisions of, any of these
publications do not apply. However, parties to agreements based on this International Standard are encouraged to
investigate the possibility of applying the most recent editions of the normative documents indicated below. For
undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC
maintain registers of currently valid International Standards.
1)
ISO 1940-1:— , Mechanical vibration — Balance quality requirements of rigid rotors — Part 1: Determination of
permissible residual unbalance
ISO 3744, Acoustics — Determination of sound power levels of noise sources using sound pressure —
Engineering method in an essentially free field over a reflecting plane
ISO 3977-5, Gas turbines — Procurement — Part 5: Applications for petroleum and
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.