EN 15014:2007
(Main)Plastics piping systems - Buried and above ground systems for water and other fluids under pressure - Performance characteristics for pipes, fittings and their joints
Plastics piping systems - Buried and above ground systems for water and other fluids under pressure - Performance characteristics for pipes, fittings and their joints
This European Standard specifies performance requirements for plastics pipes, fittings and their joints for buried or above-ground pressure applications for water for general purposes, drainage, sewerage and irrigation, as well as for any other pressure application with other fluids covered by the Construction Products Directive with the exception of drinking water distribution for human consumption. It gives associated test methods for verification and evaluation of conformity with this European Standard.
NOTE Compliance of pipes, fittings and their joints with this document does not confer a presumption of fitness of the product for the transport of water intended for human consumption within the meaning of the Directive 89/106/EEC. However, until the operation of the envisaged European Acceptance Scheme for construction products in contact with water intended for human consumption and the revision of the present standard, products complying with the present standard could be used for the transport of water intended for human consumption if they comply with the relevant national, regional or local regulatory provisions applicable in the place of use.
Kunststoff-Rohrleitungssysteme - Erd- und oberirdisch verlegte Druckrohrleitungssysteme für Wasser und andere Flüssigkeiten - Eigenschaften für die Gebrauchstauglichkeit von Rohren, Formstücken und deren Verbindungen
Dieses Dokument legt Leistungsanforderungen an Kunststoffrohre, -formstücke und deren Verbindungen für erd- und oberirdisch verlegte Druckrohrleitungssysteme für Betriebswasser, Entwässerung, Abwasser und Bewässerung fest, sowie für jede andere Anwendung mit Flüssigkeiten unter Druck, die in der Bauproduktenrichtlinie enthalten ist, ausgenommen die Verteilung von Trinkwasser. Es gibt damit verbundene Prüfverfahren zur Verifizierung und Bewertung der Konformität mit diesem Dokument an.
ANMERKUNG Für diese Anwendung werden "Scheiteldruckfestigkeit", "Biegefestigkeit in Längsrichtung", "Höchstlast für zulässige Verformung", "Widerstandsfähigkeit gegen hohe Temperaturen (bei Heizungsanlagen)", "Schlagzähigkeit", "Schweißbarkeit (bei Gasleitungsnetzen)", "Widerstandsfähigkeit gegen Durchdringung (bei Gasleitungsnetzen)", "elektrostatisches Verhalten (bei Brennstoffleitungsnetzen)", "Durchlässigkeit", "thermische Eigenschaften" und "Wärmeisolierung (hinsichtlich Energieeinsparung)" nicht behandelt.
Systèmes de canalisations en plastique - Systèmes enterrés et aériens pour eau et autres fluides avec pression - Caractéristiques de performance pour tubes, raccords et leurs assemblages
La présente Norme européenne spécifie les exigences de performance pour les tubes, raccords en plastique et leurs assemblages destinés aux applications enterrées ou aériennes avec pression pour eau à usages généraux, branchements, collecteurs d'assainissement et irrigation ainsi que pour toute autre application avec pression pour d’autres fluides couverte par la Directive sur les Produits de Construction, à l’exception de la distribution de l’eau potable destinée à la consommation humaine. Il indique les méthodes associées pour la vérification et l’évaluation de la conformité la présente Norme européenne.
NOTE La conformité des tubes, raccords et de leurs assemblages au présent document ne confère pas une présomption d’aptitude du produit pour le transport de l’eau destinée à la consommation humaine au sens de la Directive 89/106/CEE. Cependant, jusqu’à la mise en application du Plan d’Acceptation Européen (EAS) pour les produits de construction en contact avec l’eau destinée à la consommation humaine et la révision de la présente norme, les produits en conformité avec le présent document pourront être utilisés pour le transport de l’eau destinée à la consommation humaine s’ils satisfont les dispositions réglementaires nationales, régionales ou locales pertinentes applicables au lieu d’usage.
Cevni sistemi iz polimernih materialov - Podzemni in nadzemni sistemi za vodo in druge tekočine pod tlakom - Lastnosti cevi, fitingov in njihovih spojev
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Plastics piping systems - Buried and above ground systems for water and other fluids under pressure - Performance characteristics for pipes, fittings and their jointsVSRMHYSystemes de canalisations en plastique - Systemes enterrés et aériens pour eau et autres fluides avec pression - Caractéristiques de performance pour tubes, raccords et leurs assemblagesKunststoff-Rohrleitungssysteme - Erd- und oberirdisch verlegte Druckrohrleitungssysteme für Wasser und andere Flüssigkeiten - Eigenschaften für die Gebrauchstauglichkeit von Rohren, Formstücken und deren VerbindungenTa slovenski standard je istoveten z:EN 15014:2007SIST EN 15014:2008en,fr,de91.140.80Drenažni sistemiDrainage systems23.040.45Fitingi iz polimernih materialovPlastics fittings23.040.20Cevi iz polimernih materialovPlastics pipesICS:SLOVENSKI
STANDARDSIST EN 15014:200801-januar-2008
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 15014October 2007ICS 23.040.20; 23.040.45 English VersionPlastics piping systems - Buried and above ground systems forwater and other fluids under pressure - Performancecharacteristics for pipes, fittings and their jointsSystèmes de canalisations en plastique - Systèmesenterrés et aériens pour eau et autres fluides avec pression- Caractéristiques de performance pour tubes, raccords etleurs assemblagesKunststoff-Rohrleitungssysteme - Erd- und oberirdischverlegte Druckrohrleitungssysteme für Wasser und andereFlüssigkeiten - Eigenschaften für die Gebrauchstauglichkeitvon Rohren, Formstücken und deren VerbindungenThis European Standard was approved by CEN on 23 August 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2007 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 15014:2007: E
Product standards for buried and above-ground pressure piping systems in plastics materials for water for general purposes, drainage, sewerage, irrigation and other fluids.17 Annex B (normative)
Standards for assessment of conformity for buried and above-ground pressure piping systems in plastics materials for water for general purposes, drainage, sewerage, irrigation and other fluids.19 Annex ZA (informative)
Clauses of this European Standard addressing the provisions of EU Construction Products Directive.20 ZA.1 Scope and relevant characteristics.20 ZA.2 Procedure for attestation of conformity of plastics pipes and fittings.21 ZA.2.1 Systems of attestation of conformity.21 ZA.2.2 EC Certificate and Declaration of conformity.23 ZA.3 CE marking and labelling.25 ZA.3.1 CE marking requirements.25 ZA.3.2 Simplified CE marking with reference to a web site.26 ZA.3.2.1 General.26 ZA.3.2.2 Minimum rules for the proper use of a web site for CE marking information.28 Bibliography.29
Material independent
Specific solutions
For the harmonisation of pressure plastics piping systems (this European Standard) the following applies:
For pipes and fittings
For valves Figure 1
Compliance of pipes, fittings and their joints with this document does not confer a presumption of fitness of the product for the transport of water intended for human consumption within the meaning of the Directive 89/106/EEC. However, until the operation of the envisaged European Acceptance Scheme for construction products in contact with water intended for human consumption and the revision of this standard, products conforming to this standard could be used for the transport of water intended for human consumption if they conform to the relevant national, regional or local regulatory provisions or recommendations applicable in the place of use. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 681-1,
Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage applications — Part 1: Vulcanized rubber EN 681-2,
Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage applications — Part 2: Thermoplastic elastomers EN 681-4,
Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage applications — Part 4: Cast polyurethane sealing elements EN 713,
Plastics piping systems — Mechanical joints between fittings and polyolefin pressure pipes — Test method for leaktightness under internal pressure of assemblies subjected to bending EN 715,
Thermoplastics piping systems — End-load bearing joints between small diameter pressure pipes and fittings — Test method for leaktightness under internal water pressure, including end thrust EN 911,
Plastics piping systems — Elastomeric sealing ring type joints and mechanical joints for thermoplastics pressure piping — Test method for leaktightness under external hydrostatic pressure EN 1394,
Plastics piping systems — Glass-reinforced thermosetting plastics (GRP) pipes — Determination of the apparent initial circumferential tensile strength EN 1796,
Plastics piping systems for water supply with or without pressure — Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) EN 13501-1,
Fire classification of construction products and
building elements — Part 1: Classification using test data from reaction to fire tests EN 14364,
Plastics piping systems for drainage and sewerage with or without pressure — Glass-reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) — Specifications for pipes, fittings and joints EN 15012:2007,
Plastics piping systems — Soil and waste discharge systems within the building structure — Performance characteristics for pipes, fittings and their joints
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 1: General method (ISO 1167-1:2006) EN ISO 1167-2,
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces (ISO 1167-2:2006) prEN ISO 1167-3:2005,
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 3: Preparation of components
(ISO/DIS 1167-3:2005) prEN ISO 1167-4:2006,
Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 4: Pr
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.