EN ISO 14246:2001

Transportable gas cylinders - Gas cylinder valves - Manufacturing tests and inspections (ISO 14246:2001)

This Euroepan Standard defines the requirements for tests and inspections of gas cylinder valves at time of their manufacture. This standard is applicable to valves to be fitted to gas cylinders, up to 150 l water capacity, intended to convey compressed, liquefied or dissolved gases. This Standard is only applicable to valves operated by a hand wheel or a key. This Standard is not applicable to valves for breathing equipment, fire extinguishers, cryogenic equipment and liquefied petroleum gas (LPG).

Ortsbewegliche Gasflaschen - Gasflaschen-Ventile - Herstellungsprüfungen und Überprüfungen (ISO 14246:2001)

Diese Europäische Norm enthält Anforderungen an die Prüfung und die Überprüfung von Gasflaschenventilen zum Zeitpunkt der Herstellung. Diese Norm ist anzuwenden für Ventile an Gasflaschen mit einem Fassungsraum bis zu 150 l zur Beförderung von verdichteten, verflüssigten und unter Druck gelösten Gasen. Diese Norm gilt für Ventile, die mit einem Handrad oder einem Schlüssel betätigt werden. Diese Norm gilt nicht für Ventile für den Atemschutz, für Feuerlöscher, für Kryo-Behälter und für Flüssiggas (LPG).

Bouteilles à gaz transportables - Robinets de bouteilles à gaz - Essais de fabrication et contrôlés (ISO 14246:2001)

La présente norme spécifie les exigences pour les essais et contrôles des robinets des bouteilles à gaz lors de la fabrication. La présente norme est applicable aux robinets destinés à être montés sur les bouteilles pour gaz industriels et médicaux de contenance en eau jusqu'à 150 l, destinées aux gaz comprimés, liquéfiés ou dissous. La présente norme n'est applicable qu'aux robinets manoeuvrables par un volant à main ou une clé. La présente norme n'est pas applicable aux robinets pour équipement respiratoire, extincteurs, équipement cryogénique et gaz de pétrole liquéfié (GPL).

Premične plinske jeklenke - Ventili plinskih jeklenk - Proizvodni preskusi in dodatne kontrole (ISO 14246:2001)

General Information

• Status: Withdrawn
• Publication Date: 31-Mar-2001
• Withdrawal Date: 15-Jul-2014
• ICS: 23.020 - Fluid storage devices
• ICS: 23.020.35 - Gas cylinders
• Technical Committee: CEN/TC 23 - Transportable gas cylinders
• Drafting Committee: CEN/TC 23/SC 2 - Fittings
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 16-Jul-2014
• Ref Project: SIST EN ISO 14246:2002 - Transportable gas cylinders - Gas cylinder valves - Manufacturing tests and inspections (ISO 14246:2001)

Relations

• Replaced By: EN ISO 14246:2014 - Gas cylinders - Cylinder valves - Manufacturing tests and examinations (ISO 14246:2014)
• Effective Date: 07-Nov-2009

Standards Content (Sample)

SLOVENSKI STANDARD
01-maj-2002
3UHPLþQHSOLQVNHMHNOHQNH9HQWLOLSOLQVNLKMHNOHQN3URL]YRGQLSUHVNXVLLQ
GRGDWQHNRQWUROH,62
Transportable gas cylinders - Gas cylinder valves - Manufacturing tests and inspections
(ISO 14246:2001)
Ortsbewegliche Gasflaschen - Gasflaschen-Ventile - Herstellungsprüfungen und
Überprüfungen (ISO 14246:2001)
Bouteilles a gaz transportables - Robinets de bouteilles a gaz - Essais de fabrication et
contrôlés (ISO 14246:2001)
Ta slovenski standard je istoveten z: EN ISO 14246:2001
ICS:
23.020.30 7ODþQHSRVRGHSOLQVNH Pressure vessels, gas
MHNOHQNH cylinders
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN ISO 14246
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2001
ICS 23.020
English version
Transportable gas cylinders - Gas cylinder valves -
Manufacturing tests and inspections (ISO 14246:2001)
Bouteilles à gaz transportables - Robinets de bouteilles à Ortsbewegliche Gasflaschen - Gasflaschen-Ventile -
gaz - Essais de fabrication et contrôles (ISO 14246:2001) Herstellungsprüfungen und Überprüfungen (ISO
14246:2001)
This European Standard was approved by CEN on 14 December 2000.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2001 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 14246:2001 E
worldwide for CEN national Members.

Page 2
Contents Page
Foreword . 3
Introduction. 4
1 Scope. 4
2 Normative references . 4
3 Terms and definitions. 4
4 Manufacturing tests and inspections. 5
5 Test record . 6
Annex A (informative)  Example of leakage test method . 7
Annex B (informative)  Examples of revalidation procedures . 8
Bibliography . 9

Page 3
Foreword
The text of EN ISO 14246:2001 has been prepared by Technical Committee CEN/TC 23
"Transportable gas cylinders", the secretariat of which is held by BSI, in collaboration with
Technical Committee ISO/TC 58 "Gas cylinders".
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by October 2001, and conflicting national
standards shall be withdrawn at the latest by October 2001.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Czech
Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg,
Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.

Page 4
Introduction
Gas cylinders are usually fitted with a valve to contain the gas or allow its discharge.
Requirements for the specification and type testing of cylinder valves are given in EN 849.
1 Scope
This Standard specifies the requirements for tests and inspections of gas cylinder valves at time of
manufacture.
This Standard is applicable to valves to be fitted to industrial and medical gas cylinders, up to 150 l
water capacity, intended to convey compressed, liquefied or dissolved gases.
This Standard is only applicable to valves operated by a hand wheel or a key.
This Standard is not applicable to valves for breathing equipment, fire extinguishers, cryogenic
equipment and liquefied petroleum gas (LPG).
2 Normative references
This European Standard incorporates by dated or undated reference, provisions from other
publications. These normative references are cited at the appropriate places in the text and the
publications are listed hereafter. For dated references, subsequent amendments to or revisions of
any of these publications apply to this European Standard only when incorporated in it by
amendment or revision. For undated references the latest edition of the publication referred to
applies (including amendments).
Transportable gas cylinders - Gases and gas mixtures -
EN 720-2
Part 2: Determination of flammability and oxidizing ability of
gases and gas mixtures
EN 849 Transportable gas cylinders - Cylinder valves - Specification
and type testing
EN ISO 11114-3 Transportable gas cylinders - Compatibility of cylinder and
valve materials with gas contents - Part 3: Autogenous
ignition test in oxygen atmosphere (ISO 11114-3:1997)
3 Terms and definitions
For the purpose
...