EN ISO 25197:2012
(Main)Small craft - Electrical/electronic control systems for steering, shift and throttle (ISO 25197:2012)
Small craft - Electrical/electronic control systems for steering, shift and throttle (ISO 25197:2012)
ISO 25197:2012 establishes the requirements for design, construction and testing of electrical/electronic steering, shift and throttle and dynamic position control systems, or combinations thereof, on small craft of up to 24 m length of hull.
Kleine Wasserfahrzeuge - Elektrische/elektronische Regelungssysteme für Steuerung, Schaltung und Antrieb (ISO 25197:2012)
Diese Internationale Norm legt die Anforderungen für den Entwurf, die Ausführung und die Prüfung von elektrischen/ elektronischen Systemen für die Steuerung, Getriebeschaltung und die Drehzahlregelung, sowie von dynamischen Positionskontrollsystemen oder Kombinationen davon auf kleinen Wasserfahrzeugen mit einer Rumpflänge bis 24 m fest.
Petits navires - Systèmes électriques/électroniques pour le contrôle de la direction, de l'inverseur et des gaz (ISO 25197:2012)
L'ISO 25197:2012 établit les exigences concernant la conception, la construction et les essais des systèmes électriques/électroniques de contrôle de la direction, des commandes d'inverseur, des gaz et du positionnement dynamique, ou de leur combinaison, sur les bateaux d'une longueur de coque inférieure ou égale à 24 m.
Mala plovila - Električni/elektronski sistemi regulacije za krmarjenje, prestavljanje in pogon (ISO 25197:2012)
Ta mednarodni standard določa zahteve za načrtovanje, konstrukcijo in preskušanje električnih/elektronskih sistemov regulacije za krmarjenje, prestavljanje in pogon ter dinamično določanje položaja ali njihovo kombinacijo pri malih plovilih z dolžino trupa do 24 m.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-maj-2013
0DODSORYLOD(OHNWULþQLHOHNWURQVNLVLVWHPLUHJXODFLMH]DNUPDUMHQMHSUHVWDYOMDQMH
LQSRJRQ ,62
Small craft - Electrical/electronic control systems for steering, shift and throttle (ISO
25197:2012)
Kleine Wasserfahrzeuge - Elektrische/elektronische Regelungssysteme für Steuerung,
Schaltung und Antrieb (ISO 25197:2012)
Petits navires - Systèmes électriques/électroniques pour le contrôle de la direction, de
l'inverseur et des gaz (ISO 25197:2012)
Ta slovenski standard je istoveten z: EN ISO 25197:2012
ICS:
47.020.60 (OHNWULþQDRSUHPDODGLMLQ Electrical equipment of ships
NRQVWUXNFLMQDPRUMX and of marine structures
47.080 ýROQL Small craft
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 25197
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2012
ICS 47.080
English Version
Small craft - Electrical/electronic control systems for steering,
shift and throttle (ISO 25197:2012)
Petits navires - Systèmes électriques/électroniques pour le Kleine Wasserfahrzeuge - Elektrisches/elektronisches
contrôle de la direction, de l'inverseur et des gaz (ISO Regelungssystem für Steuerung, Schaltung und Antrieb
25197:2012) (ISO 25197:2012)
This European Standard was approved by CEN on 24 November 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 25197:2012: E
worldwide for CEN national Members.
Contents Page
Foreword . 3
Annex ZA (informative) Relationship between this European Standard and the Essential
Requirements of EU Directive 94/25/EC as amended by Directive 2003/44/EC . 4
Foreword
This document (EN ISO 25197:2012) has been prepared by Technical Committee ISO/TC 188 "Small craft".
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by June 2013, and conflicting national standards shall be withdrawn at
the latest by June 2013.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document.
According to the CEN/CENELEC Internal Regulations, the national standards organisations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorsement notice
The text of ISO 25197:2012 has been approved by CEN as a EN ISO 25197:2012 without any modification.
Annex ZA
(informative)
Relationship between this European Standard and the Essential
Requirements of EU Directive 94/25/EC as amended by Directive
2003/44/EC
This European Standard has been prepared under a mandate given to CEN by the European Commission to
provide one means of conforming to Essential Requirements of the New Approach Directive 94/25/EC as
amended by Directive 2003/44/EC.
Once this standard is cited in the Official Journal of the European Union under that Directive and has been
implemented as a national standard in at least one member state, compliance with the normative clauses of
this standard given in Table ZA.1 confers, within the limits of the scope of this standard, a presumption of
conformity with the relevant Essential Requirements of that Directive and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and EU Directives
Clauses/subclauses of this Corresponding annexes/paragraphs Comments
European Standard of Directive 94/25/EC as amended by
Directive 2003/44/EC
All Annex I.A.2, Clause 5.4, Steering
system
WARNING: Other requirements and other EU Directives may be applicable to the products falling within the
scope of this standard.
INTERNATIONAL ISO
STANDARD 25197
First edition
2012-12-01
Small craft — Electrical/electronic control
systems for steering, shift and throttle
Petits navires — Systèmes électriques/électroniques pour le contrôle de
la direction, de l’inverseur et des gaz
Reference number
ISO 25197:2012(E)
©
ISO 2012
ISO 25197:2012(E)
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2012 – All rights reserved
ISO 25197:2012(E)
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 General requirements . 4
5 Control head . 5
6 Command station transfer . 6
7 Portable helm station controls . 6
8 Dynamic-positioning system (DPS) . 7
9 Failure modes and responses . 8
9.1 Loss of operation . 8
9.2 Loss of computer command logic . 8
10 Test requirements . 8
10.1 General test requirements . 8
10.2 Steering . 8
10.3 Joystick . 9
10.4 Control lever, single or combined, shift and throttle .10
10.5 Environmental-test requirements . 11
10.6 Vibration tests and requirements .13
10.7 Shock testing .14
10.8 Free fall .14
10.9 Resistance to UV .14
10.10 Electromagnetic compatibility (EMC) .15
10.11 Compass safe distance .17
10.12 Insulation resistance .17
11 Labelling .17
12 Instructions to be included with the owner’s manual .18
ISO 25197:2012(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International
Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 25197 was prepared by Technical Committee ISO/TC 188, Small craft.
iv © ISO 2012 – All rights reserved
INTERNATIONAL STANDARD ISO 25197:2012(E)
Small craft — Electrical/electronic control systems for steering,
shift and throttle
1 Scope
This International Standard establishes the requirements for design, construction and testing of
electrical/electronic steering, shift and throttle and dynamic position control systems, or combinations thereof,
on small craft of up to 24 m length of hull.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced document
(including any amendments) applies.
ISO 8846, Small craft — Electrical devices — Protection against ignition of surrounding flammable gases.
ISO 8848, Small craft — Remote steering systems
ISO 10133, Small craft — Electrical systems — Extra-low-voltage d.c. installations
ISO 10240, Small craft — Owner’s manual
ISO 10592, Small craft — Hydraulic steering systems
ISO 11591, Small craft, engine-driven — Field of vision from helm position
ISO 12215-8, Small craft — Hull construction and scantlings — Part 8: Rudders
ISO 13297, Small craft — Electrical systems — Alternating current installations
ISO 16750-2:2010, Road vehicles — Environmental conditions and testing for electrical and electronic
equipment — Part 2: Electrical loads
ISO 16750-3:2007, Road vehicles —
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.