CEN/TS 13388:2020
(Main)Copper and copper alloys - Compendium of compositions and products
Copper and copper alloys - Compendium of compositions and products
This document provides a summary of material designations, compositions and the product forms in which they are available, for coppers and copper alloys standardized in European Standards by CEN/TC 133 "Copper and copper alloys".
Kupfer und Kupferlegierungen - Übersicht über Zusammensetzungen und Produkte
Dieses Dokument gibt eine Übersicht über Werkstoffbezeichnungen, Zusammensetzungen und die lieferbaren Produktformen von Kupfer und Kupferlegierungen, die in den Europäischen Normen des CEN/TC 133 „Kupfer und Kupferlegierungen“ genormt sind.
Cuivre et alliages de cuivre - Inventaire des compositions et des produits
Le présent document fournit un résumé sur les désignations des matériaux, les compositions et les formes de produits disponibles, pour les cuivres et alliages de cuivre normalisés dans les Normes européennes par le CEN/TC 133 « Cuivre et alliages de cuivre ».
Baker in bakrove zlitine - Zbirka kemijskih sestav in izdelkov
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-maj-2020
Nadomešča:
SIST-TS CEN/TS 13388:2015
Baker in bakrove zlitine - Zbirka kemijskih sestav in izdelkov
Copper and copper alloys - Compendium of compositions and products
Kupfer und Kupferlegierungen - Übersicht über Zusammensetzungen und Produkte
Cuivre et alliages de cuivre - Inventaire des compositions et des produits
Ta slovenski standard je istoveten z: CEN/TS 13388:2020
ICS:
77.120.30 Baker in bakrove zlitine Copper and copper alloys
77.150.30 Bakreni izdelki Copper products
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
CEN/TS 13388
TECHNICAL SPECIFICATION
SPÉCIFICATION TECHNIQUE
April 2020
TECHNISCHE SPEZIFIKATION
ICS 77.120.30; 77.150.30 Supersedes CEN/TS 13388:2015
English Version
Copper and copper alloys - Compendium of compositions
and products
Cuivre et alliages de cuivre - Inventaire des Kupfer und Kupferlegierungen - Übersicht über
compositions et des produits Zusammensetzungen und Produkte
This Technical Specification (CEN/TS) was approved by CEN on 21 October 2019 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to
submit their comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS
available promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in
parallel to the CEN/TS) until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 13388:2020 E
worldwide for CEN national Members.
Contents Page
European foreword . 4
Introduction . 5
1 Scope . 6
2 Normative references . 6
3 Compositions of coppers and copper alloys standardised by CEN/TC 133. 6
3.1 Composition of coppers . 6
3.2 Composition of copper alloys. 6
3.3 Composition of master alloys . 7
3.4 Composition of ingots and castings . 7
3.5 Composition of copper and copper alloy scrap . 7
4 Available product forms of copper and copper alloys . 8
4.1 Wrought coppers and copper alloys . 8
4.2 Master alloys . 8
4.3 Ingots and castings . 8
4.4 Scrap . 8
4.5 Copper and copper alloy grooved contact wires . 8
Bibliography . 63
Tables
Table 1.1 — Composition of copper cathodes according to EN 1978:1998, Cu-CATH-1
(CR001A) and Cu-CATH-2 (CR002A) . 9
Table 1.2 — Composition of unalloyed copper grades made from Cu-CATH-1 (CR001A)
according to EN 1978 . 10
Table 1.3 — Composition of unalloyed copper grades, other than those made from Cu-
CATH-1 (CR001A) according to EN 1978 . 12
Table 1.4 — Composition of phosphorus-containing copper grades . 13
Table 1.5 — Composition of silver-containing copper grades (silver-bearing coppers) . 14
Table 2 — Composition of copper alloys, low alloyed (less than 5 % alloying elements) . 15
Table 3 — Composition of copper-aluminium alloys . 17
Table 4 — Composition of copper-nickel alloys . 18
Table 5 — Composition of copper-nickel-zinc alloys . 19
Table 6 — Composition of copper-tin alloys. 20
Table 7 — Composition of copper-zinc alloys, binary . 21
Table 8 — Composition of copper-zinc-lead alloys . 22
Table 9 — Composition of copper-zinc alloys, complex . 24
Table 10 — Wrought coppers and copper alloys specified in European product Standards
prepared by CEN/TC 133 . 26
Table 11 — Master alloys — Composition . 39
Table 12.1 — Ingots and castings — Copper and copper-chromium alloys — Compositions
and casting processes. 43
Table 12.2 — Ingots and castings — Copper-zinc alloys — Composition and casting
processes . 44
Table 12.3 — Ingots and castings — Copper-zinc-aluminium alloys — Composition and
casting processes . 45
Table 12.4 — Ingots and castings — Copper-zinc-lead alloys — Composition and casting
processes . 46
Table 12.5 — Ingots and castings — Copper-zinc-silicon alloys — Composition and casting
processes . 49
Table 12.6 — Ingots and castings — Other copper-zinc alloys — Composition and casting
processes . 50
Table 12.7 — Ingots and castings — Copper-tin alloys — Composition and casting processes . 51
Table 12.8 — Ingots and castings — Copper-tin-zinc-lead alloys — Composition and casting
processes . 52
Table 12.9 — Ingots and castings — Copper-tin-lead alloys — Composition and casting
processes . 53
Table 12.10 — Ingots and castings — Copper-aluminium alloys — Composition and casting
processes . 54
Table 12.11 — Ingots and castings — Copper-manganese alloys — Composition and casting
processes . 55
Table 12.12 — Ingots and castings — Copper-nickel alloys — Composition and casting
processes . 56
Table 12.13 — Ingots and castings — Copper-silicon-zinc alloys — Composition and casting
processes . 57
Table 13 — Scrap — Composition . 58
Table 14 — Composition of copper alloy according to EN 50149:2012 . 62
European foreword
This document (CEN/TS 13388:2020) has been prepared by Technical Committee CEN/TC 133 “Copper
and copper alloys”, the secretariat of which is held by DIN.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes CEN/TS 13388:2015.
In comparison with CEN/TS 13388:2015, the following changes were made:
a) modifications regarding materials and compositions from EN 1982:2017, EN 12164:2016,
EN 12165:2016, EN 12167:2016, EN 12168:2016, EN 12449:2016+A1:2019, EN 12735-1:2016 and
EN 12861:2018 considered.
According to the CEN/CENELEC Internal Regulations, the national standards organisations of the
following countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Introduction
CEN/TC 133 “Copper and copper alloys” was established in 1988 to prepare and maintain standards in
the field of unwrought, wrought and cast products made from copper and copper alloys. Its
responsibilities included developing, defining, specifying and giving guidance on, as appropriate,
material compositions, designations, terminology, dimensions and tolerances, mechanical and physical
characteristics, conditions of delivery and methods of testing peculiar to copper and copper alloys.
During the development of standards for copper and copper alloy products, the experts realized the
necessity and seized the opportunity:
a) to coordinate and in some cases also to rationalize the composition limits which already existed for
the various product forms;
b) to establish unique, new and identifiably European designations for copper and copper alloys,
including a numerical option to be particularly convenient for computerized handling;
c) to confirm, clarify and redefine where necessary, the terminology which already existed in common
usage, at the international level or in customs nomenclature.
CEN/TC 133 decided, in view of the new form of presentation and new parameters for the description
and provision of information on copper and copper alloy products, to prepare and publish the present
consolidation and summary of essential details.
1 Scope
This document provides a summary of material designations, compositions and the product forms in
which they are available, for coppers and copper alloys standardized in European Standards by
CEN/TC 133 “Copper and copper alloys”.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
EN 1976, Copper and copper alloys — Cast unwrought copper products
EN 1982:2017, Copper and copper alloys — Ingots and castings
3 Compositions of coppers and copper alloys standardised by CEN/TC 133
3.1 Composition of coppers
The symbol and number designations and compositions of copper grades are given in the following
tables:
Table 1.1 — Composition of copper cathodes according to EN 1978:1998, Cu-CATH-1 (CR001A) and
Cu-CATH-2 (CR002A)
Table 1.2 — Composition of unalloyed copper grades made from Cu-CATH-1 (CR001A) according to
EN 1978
Table 1.3 — Composition of unalloyed copper grades, other than those made from Cu-CATH-1
(CR001A) according to EN 1978
Table 1.4 — Composition of phosphorus-containing copper grades
Table 1.5 — Composition of silver-containing copper grades (silver-bearing coppers)
3.2 Composition of copper alloys
The symbol and number designations and compositions of copper alloys are given in the following
tables:
Table 2 — Composition of copper alloys, low alloyed (less than 5 % alloying elements)
Table 3 — Composition of copper-aluminium alloys
Table 4 — Composition of copper-nickel alloys
Table 5 — Composition of copper-nickel-zinc alloys
Table 6 — Composition of copper-tin alloys
Table 7 — Composition of copper-zinc alloys, binary
Table 8 — Composition of copper-zinc-lead alloys
Table 9 — Composition of copper-zinc alloys, complex
3.3 Composition of master alloys
The symbol and number designations and compositions of master alloys in accordance with
EN 1981:2003 are given in Table 11.
3.4 Composition of ingots and castings
The symbol and number designations and compositions of ingots and castings in accordance with
EN 1982:2017 are given in the following tables:
Table 12.1 — Ingots and castings — Copper and copper-chromium alloys — Compositions and
casting processes
Table 12.2 — Ingots and castings — Copper-zinc alloys — Composition and casting processes
Table 12.3 — Ingots and castings — Copper-zinc-aluminium alloys — Composition and casting
processes
Table 12.4 — Ingots and castings — Copper-zinc-lead alloys — Composition and casting processes
Table 12.5 — Ingots and castings — Copper-zinc-silicon alloys — Composition and casting
processes
Table 12.6 — Ingots and castings — Other copper-zinc alloys — Composition and casting processes
Table 12.7 — Ingots and castings — Copper-tin alloys — Composition and casting processes
Table 12.8 — Ingots and castings — Copper-tin-zinc-lead alloys — Composition and casting
processes
Table 12.9 — Ingots and castings — Copper-tin-lead alloys — Composition and casting processes
Table 12.10 — Ingots and castings — Copper-aluminium alloys — Composition and casting
processes
Table 12.11 — Ingots and castings — Copper-manganese alloys — Composition and casting
processes
Table 12.12 — Ingots and castings — Copper-nickel alloys — Composition and casting processes
Table 12.13 — Ingots and castings — Copper-silicon-zinc alloys — Composition and casting
processes
3.5 Composition of copper and copper alloy scrap
The symbol and number designations and compositions of copper and copper alloy scrap in accordance
with EN 12861:2018 are given in Table 13.
4 Available product forms of copper and copper alloys
4.1 Wrought coppers and copper alloys
The product forms and applicable standards are given in Table 10.
4.2 Master alloys
The product forms are given in Table 11.
4.3 Ingots and castings
The product forms are given in Tables 12.1 to 12.13.
4.4 Scrap
The product forms are given in Table 13.
4.5 Copper and copper alloy grooved contact wires
The product forms are given in Table 14.
Table 1.1 — Composition of copper cathodes according to EN 1978:1998, Cu-CATH-1 (CR001A) and Cu-CATH-2 (CR002A)
Material Composition in % (mass fraction)
designation Sum of elements listed in this table
Element Cu Ag As Bi Cd Co Cr Fe Mn Ni P Pb S Sb Se Si Sn Te Zn
other than copper
Symbol Number
min. — — — — — — — — — — — — — — — — — — — —
Cu-
CR001A
0,000 5 0,000 20 — — — 0,001 0 — — — 0,001 5 0,000 4 0,000 20 — — 0,000 20 —
CATH-1
max. — 0,002 5 0,000 5 0,006 5
a b a c a c a c a d a b c c b c
min. 99,90 — — — — — — — — — — — — — — — — — — —
Cu-
e
CR002A
CATH-2
max. — — — 0,000 5 — — — — — — — 0,005 — — — — — — — 0,03 excluding Ag
a
(As + Cd + Cr + Mn + P + Sb) maximum 0,001 5 %.
b
(Bi + Se + Te) maximum 0,000 3 %, of which (Se + Te) maximum 0,000 30 %.
c
(Co + Fe + Ni + Si + Sn + Zn) maximum 0,002 0 %.
d
The sulfur content shall be determined on a cast sample.
e
Including silver up to a maximum of 0,015 %.
Table 1.2 — Composition of unalloyed copper grades made from Cu-CATH-1 (CR001A) according to EN 1978
Material designation Composition in % (mass fraction)
Symbol Number
Elemen
Cu Ag As Bi Cd Co Cr Fe Mn Ni O P Pb
unwroug wrought
t
ht copper copper
—
— — — — — — — —
min. — — — —
0,000 20
Cu-ETP1 CR003A CW003A
a a c a c a c a
max. — 0,002 5 0,040 0,000 5
0,000 5 — — — 0,001 0 — — —
b
—
— — — — — — — — —
min. — — —
Cu-OF1 CR007A CW007A 0,000 20
a a c a c a c d a
max. — 0,002 5 0,000 5
0,000 5 — — — 0,001 0 — — — —
b
—
min. 99,99 — — — — — — — — — — —
Cu-OFE CR009A CW009A
d
max. — 0,002 5 0,000 5 0,000 20 0,000 1 — — 0,001 0 0,000 5 0,001 0 0,000 3 0,000 5
—
—
min. 99,99 — — — — — — — — — 0,001 —
Cu-PHCE CR022A CW022A
d
max. — 0,002 5 0,000 5 0,000 20 0,000 1 — — 0,001 0 0,000 5 0,001 0 0,006 0,000 5
—
Material designation Composition in % (mass fraction)
Elements listed in this
Symbol Number
table other than copper
Element S Sb Se Si Sn Te Zn
unwrought wrought
total excluding
copper copper
— — — — — —
min. — —
Cu-ETP1 CR003A CW003A O
a b c c b c
max. 0,001 5 0,006 5
0,000 4 0,000 20 — — 0,000 20 —
— — — — — —
min. — —
Cu-OF1 CR007A CW007A O
a b c c b c
max. 0,001 5 0,006 5
0,000 4 0,000 20 — — 0,000 20 —
Cu-OFE CR009A CW009A —
min. — — — — — — — —
Material designation Composition in % (mass fraction)
Elements listed in this
Symbol Number
table other than copper
Element S Sb Se Si Sn Te Zn
unwrought wrought
total excluding
copper copper
max. 0,001 5 0,000 4 0,000 20 — 0,000 2 0,000 20 0,000 1 —
min. — — — — — — — —
Cu-PHCE CR022A CW022A —
max. 0,001 5 0,000 4 0,000 20 — 0,000 2 0,000 20 0,000 1 —
a
(As + Cd + Cr + Mn + P + Sb) max. 0,001 5 %.
b
(Bi + Se + Te) max. 0,000 3 %, of which (Se + Te) max. 0,000 30 %.
c
(Co + Fe + Ni + Si + Sn + Zn) max. 0,002 0 %.
d
The oxygen content shall be controlled by the manufacturer so that the material conforms to the hydrogen embrittlement requirements of EN 1976.
Table 1.3 — Composition of unalloyed copper grades,
other than those made from Cu-CATH-1 (CR001A) according to EN 1978
Material designation Composition in % (mass fraction)
Symbol Number
Other elements
a (see note)
Element Bi O Pb
unwrought wrought Cu
copper copper
total excluding
—
min. 99,90 — — —
Cu-ETP CR004A CW004A Ag, O
b
max. — 0,000 5 0,005 0,03
0,040
— —
min. 99,90 — —
Cu-FRHC CR005A CW005A Ag, O
b d
max. — — —
0,040 0,06
min. 99,90 — — — —
Cu-FRTP CR006A CW006A Ag, Ni, O
max. — — 0,100 — 0,05
—
min. 99,95 — — —
Cu-OF CR008A CW008A Ag
c
max. — 0,000 5 0,005 0,03
—
NOTE The total of other elements (than copper) is defined as the sum of Ag, As, Bi, Cd, Co, Cr, Fe, Mn, Ni, O, P, Pb,
S, Sb, Se, Si, Sn, Te and Zn, subject to the exclusion of any individual elements indicated.
a
Including silver, up to a maximum of 0,015 %.
b
Oxygen content up to 0,060 % is permitted, subject to agreement between the purchaser and the supplier.
c
The oxygen content shall be controlled by the manufacturer so that the material conforms to the hydrogen embrittlement
requirements of EN 1976.
d
Higher total impurities content is permitted, subject to agreement between the purchaser and the supplier.
Table 1.4 — Composition of phosphorus-containing copper grades
Material designation Composition in % (mass fraction)
Symbol Number
Other elements
(see note)
a
Element Bi P Pb
Cu
unwrought wrought
copper copper
total excluding
—
min. 99,95 — 0,001 —
Cu-PHC CR020A CW020A Ag, P
b
max. — 0,000 5 0,006 0,005
0,03
—
min. 99,95 — 0,002 —
Cu-HCP CR021A CW021A Ag, P
b
max. — 0,000 5 0,007 0,005
0,03
min. 99,90 — 0,005 — —
Cu-DLP CR023A CW023A Ag, Ni, P
max. — 0,000 5 0,013 0,005 0,03
—
min. 99,90 — 0,015 —
Cu-DHP CR024A CW024A —
c
max. — — 0,040 —
—
min. 99,90 — 0,04 — —
Cu-DXP CR025A — Ag, Ni, P
max. — 0,000 5 0,06 0,005 0,03
NOTE The total of other elements (than copper) is defined as the sum of Ag, As, Bi, Cd, Co, Cr, Fe, Mn, Ni, O, P, Pb,
S, Sb, Se, Si, Sn, Te and Zn, subject to the exclusion of any individual elements indicated.
a
Including silver, up to a maximum of 0,015 %.
b
The oxygen content shall be controlled by the manufacturer so that the material conforms to the hydrogen embrittlement
requirements of EN 1976.
c
If required, the permitted total of elements, other than silver and phosphorus, should be agreed between the purchaser and the
supplier.
Table 1.5 — Composition of silver-containing copper grades (silver-bearing coppers)
Material designation Composition in % (mass fraction)
Other elements
Symbol Number
(see note)
Element Cu Ag Bi O P
unwrought wrought
copper copper
total excluding
min. Rem. 0,03 — — — —
CuAg0,04 CR011A CW011A Ag, O
max. — 0,05 0,000 5 0,040 — 0,03
min. Rem. 0,06 — — — —
CuAg0,07 CR012A CW012A Ag, O
max. — 0,08 0,000 5 0,040 — 0,03
min. Rem. 0,08 — — — —
CuAg0,10 CR013A CW013A Ag, O
max. — 0,12 0,000 5 0,040 — 0,03
—
min. Rem. 0,03 — 0,001 —
CuAg0,04P CR014A CW014A Ag, P
a
max. — 0,05 0,000 5 0,007 0,03
—
—
min. Rem. 0,06 — 0,001 —
CuAg0,07P CR015A CW015A Ag, P
a
max. — 0,08 0,000 5 0,007 0,03
—
—
min. Rem. 0,08 — 0,001 —
CuAg0,10P CR016A CW016A Ag, P
a
max. — 0,12 0,000 5 0,007 0,03
—
—
min. Rem. 0,03 — — —
CuAg0,04(OF) CR017A CW017A Ag, O
a
max. — 0,05 0,000 5 — 0,006 5
—
—
min. Rem. 0,06 — — —
CuAg0,07(OF) CR018A CW018A Ag, O
a
max. — 0,08 0,000 5 — 0,006 5
—
—
min. Rem. 0,08 — — —
CuAg0,10(OF) CR019A CW019A Ag, O
a
max. — 0,12 0,000 5 — 0,006 5
—
NOTE The total of other elements (than copper) is defined as the sum of Ag, As, Bi, Cd, Co, Cr, Fe, Mn, Ni, O, P, Pb, S,
Sb, Se, Si, Sn, Te and Zn, subject to the exclusion of any individual elements indicated.
a
The oxygen content shall be controlled by the manufacturer so that the material conforms to the hydrogen
embrittlement requirements of EN 1976.
Table 2 — Composition of copper alloys, low alloyed (less than 5 % alloying elements)
a
Density
Material designation Composition in % (mass fraction)
g/cm
Others
Symbol Number Element Cu Al Be Co Cr Fe Mn Ni P Pb S Si Sn Te Zn Zr
total approx.
min. Rem. — 1,6 — — — — — — — — — — — — — —
CuBe1,7 CW100C 8,3
max. — — 1,8 0,3 — 0,2 — 0,3 — — — — — — — — 0,5
min. Rem. — 1,8 — — — — — — — — — — — — — —
CuBe2 CW101C 8,3
max. — — 2,1 0,3 — 0,2 — 0,3 — — — — — — — — 0,5
min. Rem. — 1,8 — — — — — — 0,2 — — — — — — —
CuBe2Pb CW102C 8,3
max. — — 2,0 0,3 — 0,2 — 0,3 — 0,6 — — — — — — 0,5
min. Rem. — 0,4 0,8 — — — 0,8 — — — — — — — — —
CuCo1Ni1Be CW103C 8,8
max. — — 0,7 1,3 — 0,2 — 1,3 — — — — — — — — 0,5
min. Rem. — 0,4 2,0 — — — — — — — — — — — — —
CuCo2Be CW104C 8,8
max. — — 0,7 2,8 — 0,2 — 0,3 — — — — — — — — 0,5
min. Rem. — — — 0,5 — — — — — — — — — — — —
CuCr1 CW105C 8,9
max. — — — — 1,2 0,08 — — — — — 0,1 — — — — 0,2
min. Rem. — — — 0,5 — — — — — — — — — — 0,03 —
CuCr1Zr CW106C 8,9
max. — — — — 1,2 0,08 — — — — — 0,1 — — — 0,3 0,2
min. Rem. — — — — 2,1 — — 0,015 — — — — — 0,05 — —
CuFe2P CW107C 8,8
max. — — — — — 2,6 — — 0,15 0,03 — — — — 0,20 — 0,2
min. Rem. — — — — — — 0,8 0,15 — — — — — — — —
CuNi1P CW108C 8,9
max. — — — — — — — 1,2 0,25 — — — — — — — 0,1
min. Rem. — — — — — — 1,0 — — — 0,4 — — — — —
CuNi1Si CW109C 8,8
max. — — — — — 0,2 0,1 1,6 — 0,02 — 0,7 — — — — 0,3
min. Rem. — 0,2 — — — — 1,4 — — — — — — — — —
CuNi2Be CW110C 8,8
max. — — 0,6 0,3 — 0,2 — 2,4 — — — — — — — — 0,5
min. Rem. — — — — — — 1,6 — — — 0,4 — — — — —
CuNi2Si CW111C 8,8
max. — — — — — 0,2 0,1 2,5 — 0,02 — 0,8 — — — — 0,3
min. Rem. — — — — — — 2,6 — — — 0,8 — — — — —
CuNi3Si1 CW112C 8,8
max. — — — — — 0,2 0,1 4,5 — 0,02 — 1,3 — — — — 0,5
a
Density
Material designation Composition in % (mass fraction)
g/cm
Others
Symbol Number Element Cu Al Be Co Cr Fe Mn Ni P Pb S Si Sn Te Zn Zr
total approx.
min. Rem. — — — — — — — 0,003 0,7 — — — — — — —
CuPb1P CW113C 8,9
max. — — — — — — — — 0,012 1,5 — — — — — — 0,1
min. Rem. — — — — — — — 0,003 — 0,2 — — — — — —
CuSP CW114C 8,9
max. — — — — — — — — 0,012 — 0,7 — — — — — 0,1
min. Rem. — — — — — — — — — — 0,8 — — — — —
CuSi1 CW115C 8,8
max. — 0,02 — — — 0,8 0,7 — 0,02 0,05 — 2,0 — — 1,5 — 0,5
min. Rem. — — — — — 0,7 — — — — 2,7 — — — — —
CuSi3Mn1 CW116C 8,8
max. — 0,05 — — — 0,2 1,3 — 0,05 0,05 — 3,2 — — 0,4 — 0,5
min. Rem. — — — — — — — — — — — 0,10 — — — —
CuSn0,15 CW117C 8,9
max. — — — — — 0,02 — 0,02 0,015 — — — 0,15 — 0,10 — 0,10
min. Rem. — — — — — — — 0,003 — — — — 0,4 — — —
CuTeP CW118C 8,9
max. — — — — — — — — 0,012 — — — — 0,7 — — 0,1
min. Rem. — — — — — — — — — — — — — 0,1 — —
CuZn0,5 CW119C 8,9
max. — — — — — — — — 0,02 — — — — — 1,0 — 0,1
min. Rem. — — — — — — — — — — — — — — 0,1 —
CuZr CW120C 8,9
max. — — — — — — — — — — — — — — — 0,2 0,1
min. Rem. — — — — — — — 0,01 — — 2,5 — — 1,0 — —
CuSi3Zn2P CW124C 8,6
max. — — — — — — 0,20 0,20 0,20 0,10 — 3,5 — — 3,0 — 0,2
min. Rem. — — — — 0,05 — — 0,015 — — — 0,05 — — — —
CuFe0,1Sn0,1P CW125C 8,6
max. — — — — — 0,20 — — 0,055 — — — 0,25 — — — 0,2
a
For information only.
Table 3 — Composition of copper-aluminium alloys
Material designation Composition in % (mass fraction) Density
a
g/cm
Others
Symbol Number Element Cu Al As Fe Mn Ni P Pb Si Sn Zn
total approx.
min. Rem. 4,0 0,1 — — — — — — — — —
CuAl5As CW300G 8,2
max. – 6,5 0,4 0,2 0,2 0,2 — 0,02 — 0,05 0,3 0,3
min. Rem. 6,0 — 0,5 — — — — 2,0 — — —
CuAl6Si2Fe CW301G 7,7
max. — 6,4 — 0,7 0,1 0,1 — 0,05 2,4 0,1 0,4 0,2
min. Rem. 6,3 — — — — — — 1,5 — — —
CuAl7Si2 CW302G 7,7
max. — 7,6 — 0,3 0,2 0,2 — 0,05 2,2 0,2 0,5 0,2
min. Rem. 6,5 — 1,5 — — — — — — — —
CuAl8Fe3 CW303G 7,7
max. — 8,5 — 3,5 1,0 1,0 — 0,05 0,2 0,1 0,5 0,2
min. Rem. 8,0 — 1,0 — 2,0 — — — — — —
CuAl9Ni3Fe2 CW304G 7,4
max. — 9,5 — 3,0 2,5 4,0 — 0,05 0,1 0,1 0,2 0,3
min. Rem. 9,0 — 0,5 — — — — — — — —
CuAl10Fe1 CW305G 7,6
max. — 10,0 — 1,5 0,5 1,0 — 0,02 0,2 0,1 0,5 0,2
min. Rem. 9,0 — 2,0 1,5 — — — — — — —
CuAl10Fe3Mn2 CW306G 7,6
max. — 11,0 — 4,0 3,5 1,0 — 0,05 0,2 0,1 0,5 0,2
min. Rem. 8,5 — 3,0 — 4,0 — — — — — —
CuAl10Ni5Fe4 CW307G 7,6
max. — 11,0 — 5,0 1,0 6,0 — 0,05 0,2 0,1 0,4 0,2
min. Rem. 10,5 — 5,0 — 5,0 — — — — — —
CuAl11Fe6Ni6 CW308G 7,4
max. — 12,5 — 7,0 1,5 7,0 — 0,05 0,2 0,1 0,5 0,2
min. Rem. 4,0 — 0,15 — — — — — 0,3 4,0 — 8,2
CuAl5Zn5Sn1 CW309G
max. — 6,0 — — — — 0,05 — — 1,5 6,0 0,5
a
For information only.
Table 4 — Composition of copper-nickel alloys
a
Density
Material designation Composition in % (mass fraction)
g/cm
Others
Symbol Number Element Cu C Co Fe Mn Ni P Pb S Sn Zn
total approx.
min. Rem. — — — — 24,0 — — — — — —
CuNi25 CW350H 8,9
max. — 0,05 0,1 0,3 0,5 26,0 — 0,02 0,05 0,03 0,5 0,1
min. Rem. — — — — 8,5 — — — 1,8 — —
CuNi9Sn2 CW351H 8,9
max. — — — 0,3 0,3 10,5 — 0,03 — 2,8 0,1 0,1
—
min. Rem. — 1,0 0,5 9,0 — — — — — —
CuNi10Fe1Mn CW352H 8,9
b
max. — 0,05 2,0 1,0 11,0 0,02 0,02 0,05 0,03 0,5 0,2
0,1
—
min. Rem. — 1,5 1,5 29,0 — — — — — —
CuNi30Fe2Mn2 CW353H 8,9
b
max. — 0,05 2,5 2,5 32,0 0,02 0,02 0,05 0,05 0,5 0,2
0,1
—
min. Rem. — 0,4 0,5 30,0 — — — — — —
CuNi30Mn1Fe CW354H 8,9
b
max. — 0,05 1,0 1,5 32,0 0,02 0,02 0,05 0,05 0,5 0,2
0,1
a
For information only.
b
Co max. 0,1 % is counted as Ni.
Table 5 — Composition of copper-nickel-zinc alloys
a
Density
Material designation Composition in % (mass fraction)
g/cm
Others
Symbol Number Element Cu Fe Mn Ni Pb Sn Zn
total approx.
min. 47,0 — 1,5 6,0 2,3 — Rem. —
CuNi7Zn39Pb3Mn2 CW400J 8,5
max. 50,0 0,3 3,0 8,0 3,3 0,2 — 0,2
min. 61,0 — — 9,0 — — Rem. —
CuNi10Zn27 CW401J 8,6
max. 64,0 0,3 0,5 11,0 0,05 — — 0,2
min. 45,0 — — 9,0 1,0 — Rem. —
CuNi10Zn42Pb2 CW402J 8,4
max. 48,0 0,3 0,5 11,0 2,5 0,2 — 0,2
min. 63,0 — — 11,0 — — Rem. —
CuNi12Zn24 CW403J 8,7
max. 66,0 0,3 0,5 13,0 0,03 0,03 — 0,2
min. 60,0 — — 11,0 0,5 — Rem. —
CuNi12Zn25Pb1 CW404J 8,7
max. 63,0 0,3 0,5 13,0 1,5 0,2 — 0,2
min. 57,0 — — 11,0 — — Rem. —
CuNi12Zn29 CW405J 8,6
max. 60,0 0,3 0,5 13,5 0,03 0,03 — 0,2
min. 56,0 — — 11,0 0,5 — Rem. —
CuNi12Zn30Pb1 CW406J 8,6
max. 58,0 0,3 0,5 13,0 1,5 0,2 — 0,2
min. 42,0 — 4,5 11,0 1,0 — Rem. —
CuNi12Zn38Mn5Pb2 CW407J 8,4
max. 45,0 0,3 6,0 13,0 2,5 0,2 — 0,2
min. 59,5 — — 17,0 0,5 — Rem. —
CuNi18Zn19Pb1 CW408J 8,7
max. 62,5 0,3 0,7 19,0 1,5 0,2 — 0,2
min. 60,0 — — 17,0 — — Rem. —
CuNi18Zn20 CW409J 8,7
max. 63,0 0,3 0,5 19,0 0,03 0,03 — 0,2
min. 53,0 — — 17,0 — — Rem. —
CuNi18Zn27 CW410J 8,7
max. 56,0 0,3 0,5 19,0 0,03 0,03 — 0,2
a
For information only.
Table 6 — Composition of copper-tin alloys
a
Density
Material designation Composition in % (mass fraction)
g/cm
Others
Symbol Number Element Cu Fe Ni P Pb Sn Te Zn
total approx.
min. Rem. — — 0,01 — 3,5 — — —
CuSn4 CW450K 8,9
max. — 0,1 0,2 0,4 0,02 4,5 — 0,2 0,2
min. Rem. — — 0,01 — 4,5 — — —
CuSn5 CW451K 8,9
max. — 0,1 0,2 0,4 0,02 5,5 — 0,2 0,2
min. Rem. — — 0,01 — 5,5 — — —
CuSn6 CW452K 8,8
max. — 0,1 0,2 0,4 0,02 7,0 — 0,2 0,2
min. Rem. — — 0,01 — 7,5 — — —
CuSn8 CW453K 8,8
max. — 0,1 0,2 0,4 0,02 8,5 — 0,2 0,2
min. Rem. — — — — 1,5 — 7,5 —
CuSn3Zn9 CW454K 8,8
max. — 0,1 0,2 0,2 0,1 3,5 — 10,0 0,2
min. Rem. — — 0,2 1,5 3,5 — — —
CuSn4Pb2P CW455K 8,9
max. — 0,1 0,2 0,4 2,5 4,5 — 0,3 0,2
min. Rem. — — 0,01 3,5 3,5 — 3,5 —
CuSn4Pb4Zn4 CW456K 8,9
max. — 0,1 0,2 0,4 4,5 4,5 0,2 4,5 0,2
min. Rem. — — 0,1 — 4,0 0,5 — —
CuSn4Te1P CW457K 8,9
max. — 0,1 0,2 0,4 — 5,0 1,0 0,3 0,2
min. Rem. — — 0,01 0,5 3,5 — — —
CuSn5Pb1 CW458K 8,8
max. — 0,1 0,2 0,4 1,5 5,5 — 0,3 0,2
min. Rem. — — 0,2 — 7,5 — — —
CuSn8P CW459K 8,8
max. — 0,1 0,3 0,4 0,05 8,5 — 0,3 0,2
min. Rem. — — 0,2 0,1 7,5 — — —
CuSn8PbP CW460K 8,8
max. — 0,1 0,3 0,4 0,5 9,0 — 0,3 0,2
a
For information only.
Table 7 — Composition of copper-zinc alloys, binary
Material designation Composition in % (mass fraction) a
Density
g/cm
Others
Symbol Number Element Cu As Al Fe Ni Pb Sn Zn
total approx.
min. 94,0 — — — — — — Rem. —
CuZn5 CW500L 8,9
max. 96,0 — 0,02 0,05 0,3 0,05 0,1 — 0,1
min. 89,0 — — — — — — Rem. —
CuZn10 CW501L 8,8
max. 91,0 — 0,02 0,05 0,3 0,05 0,1 — 0,1
min. 84,0 — — — — — — Rem. —
CuZn15 CW502L 8,8
max. 86,0 — 0,02 0,05 0,3 0,05 0,1 — 0,1
min. 79,0 — — — — — — Rem. —
CuZn20 CW503L 8,7
max. 81,0 — 0,02 0,05 0,3 0,05 0,1 — 0,1
min. 71,0 — — — — — — Rem. —
CuZn28 CW504L 8,6
max. 73,0 — 0,02 0,05 0,3 0,05 0,1 — 0,1
min. 69,0 — — — — — — Rem. —
CuZn30 CW505L 8,5
max. 71,0 — 0,02 0,05 0,3 0,05 0,1 — 0,1
min. 66,0 — — — — — — Rem. —
CuZn33 CW506L 8,5
max. 68,0 — 0,02 0,05 0,3 0,05 0,1 — 0,1
min. 63,5 — — — — — — Rem. —
CuZn36 CW507L 8,4
max. 65,5 — 0,02 0,05 0,3 0,05 0,1 — 0,1
min. 62,0 — — — — — — Rem. —
CuZn37 CW508L 8,4
max. 64,0 — 0,05 0,1 0,3 0,1 0,1 — 0,1
min. 59,0 — — — — — — Rem. —
CuZn40 CW509L 8,4
max. 61,5 — 0,05 0,2 0,3 0,2 0,2 — 0,2
min. 57,0 — — — — — — Rem. —
CuZn42 CW510L 8,4
max. 59,0 — 0,05 0,3 0,3 0,2 0,3 — 0,2
min. 61,5 0,02 — — — — — Rem. —
CuZn38As CW511L 8,4
max. 63,5 0,15 0,05 0,1 0,3 0,2 0,1 — 0,2
a
For information only.
Table 8 — Composition of copper-zinc-lead alloys
a
Density
Material designation Composition in % (mass fraction)
g/cm
Others
Symbol Number Element Cu Al As Fe Mn Ni Pb Sn Zn
total approx.
min. 62,5 — — — — — 0,8 — Rem. —
CuZn35Pb1 CW600N 8,5
max. 64,0 0,05 — 0,1 — 0,3 1,6 0,1 — 0,1
min. 62,0 — — — — — 1,6 — Rem. —
CuZn35Pb2 CW601N 8,5
max. 63,5 0,05 — 0,1 — 0,3 2,5 0,1 — 0,1
min. 61,0 — 0,02 — — — 1,7 — Rem. —
CuZn36Pb2As CW602N 8,4
max. 63,0 0,05 0,15 0,1 0,1 0,3 2,8 0,1 — 0,2
min. 60,0 — — — — — 2,5 — Rem. —
CuZn36Pb3 CW603N 8,5
max. 62,0 0,05 — 0,3 — 0,3 3,5 0,2 — 0,2
min. 62,0 — — — — — 0,1 — Rem. —
CuZn37Pb0,5 CW604N 8,4
max. 64,0 0,05 — 0,1 — 0,3 0,8 0,2 — 0,2
min. 61,0 — — — — — 0,8 — Rem. —
CuZn37Pb1 CW605N 8,4
max. 62,0 0,05 — 0,2 — 0,3 1,6 0,2 — 0,2
min. 61,0 — — — — — 1,6 — Rem. —
CuZn37Pb2 CW606N 8,4
max. 62,0 0,05 — 0,2 — 0,3 2,5 0,2 — 0,2
min. 60,0 — — — — — 0,8 — Rem. —
CuZn38Pb1 CW607N 8,4
max. 61,0 0,05 — 0,2 — 0,3 1,6 0,2 — 0,2
min. 60,0 — — — — — 1,6 — Rem. —
CuZn38Pb2 CW608N 8,4
max. 61,0 0,05 — 0,2 — 0,3 2,5 0,2 — 0,2
min. 57,0 — — — — — 3,5 — Rem. —
CuZn38Pb4 CW609N 8,4
max. 59,0 0,05 — 0,3 — 0,3 4,2 0,3 — 0,2
min. 59,0 — — — — — 0,2 — Rem. —
CuZn39Pb0,5 CW610N 8,4
max. 60,5 0,05 — 0,2 — 0,3 0,8 0,2 — 0,2
min. 59,0 — — — — — 0,8 — Rem. —
CuZn39Pb1 CW611N 8,4
max. 60,0 0,05 — 0,3 — 0,3 1,6 0,2 — 0,2
min. 59,0 — — — — — 1,6 — Rem. —
CuZn39Pb2 CW612N 8,4
max. 60,0 0,05 — 0,3 — 0,3 2,5 0,3 — 0,2
min. 59,0 — — — — — 1,6 0,2 Rem. —
CuZn39Pb2Sn CW613N 8,4
max. 60,0 0,1 — 0,4 — 0,3 2,5 0,5 — 0,2
min. 57,0 — — — — — 2,5 — Rem. —
CuZn39Pb3 CW614N 8,4
max. 59,0 0,05 — 0,3 — 0,3 3,5 0,3 — 0,2
min. 57,0 — — — — — 2,5 0,2 Rem. —
CuZn39Pb3Sn CW615N 8,4
max. 59,0 0,1 — 0,4 — 0,3 3,5 0,5 — 0,2
min. 57,0 0,05 — — — — 1,0 — Rem. —
CuZn40Pb1Al CW616N 8,3
max. 59,0 0,30 — 0,2 — 0,2 2,0 0,2 — 0,2
min. 57,0 — — — — — 1,6 — Rem. —
CuZn40Pb2 CW617N 8,4
max. 59,0 0,05 — 0,3 — 0,3 2,5 0,3 — 0,2
min. 57,0 0,05 — — — — 1,6 — Rem. —
CuZn40Pb2Al CW618N 8,3
max. 59,0 0,5 — 0,3 — 0,3 3,0 0,3 — 0,2
min. 57,0 — — — — — 1,6 0,2 Rem. —
CuZn40Pb2Sn CW619N 8,4
max. 59,0 0,1 — 0,4 — 0,3 2,5 0,5 — 0,2
min. 57,0 0,05 — — — — 0,8 — Rem. —
CuZn41Pb1Al CW620N 8,3
max. 59,0 0,5 — 0,3 — 0,3 1,6 0,3 — 0,2
a
Density
Material designation Composition in % (mass fraction)
g/cm
Others
Symbol Number Element Cu Al As Fe Mn Ni Pb Sn Zn
total approx.
min. 57,0 0,05 — — — — 0,2 — Rem. —
CuZn42PbAl CW621N 8,3
max. 59,0 0,5 — 0,3 — 0,3 0,8 0,3 — 0,2
min. 55,0 0,05 — — — — 0,8 — Rem. —
CuZn43Pb1Al CW622N 8,3
max. 57,0 0,5 — 0,3 — 0,3 1,6 0,3 — 0,2
min. 55,0 — — — — — 1,6 — Rem. —
CuZn43Pb2 CW623N 8,4
max. 57,0 0,05 — 0,3 — 0,3 3,0 0,3 — 0,2
min. 55,0 0,05 — — — — 1,6 — Rem. —
CuZn43Pb2Al CW624N 8,4
max. 57,0 0,5 — 0,3 — 0,3 3,0 0,3 — 0,2
min. 62,0 0,5 0,02 — — — 1,2 — Rem. —
CuZn35Pb1,5AlAs CW625N 8,4
max. 64,0 0,7 0,15 0,3 0,1 0,2 1,6 0,3 — 0,2
min. 64,0 0,8 0,02 — — — 1,2 — Rem. —
CuZn33Pb1,5AlAs CW626N 8,4
max. 66,0 1,0 0,15 0,3 0,1 0,2 1,7 0,3 — 0,2
a
For information only.
Table 9 — Composition of copper-zinc alloys, complex
a
Density
Material designation Composition in % (mass fraction)
g/cm
Others
Symbol Number Element Cu Al As Co Fe Mn Ni P Pb Si Sn Zn
total approx.
min. 81,0 0,7 — — — — 0,8 — — 0,8 — Rem. —
CuZn13Al1Ni1Si1 CW700R 8,5
max. 84,0 1,2 — — 0,25 0,1 1,4 — 0,05 1,3 0,1 — 0,5
min. 80,0 — — — — — — — — — 0,2 Rem. —
CuZn19Sn CW701R 8,6
max. 82,0 — — — 0,05 — 0,3 — 0,05 — 0,5 — 0,2
min. 76,0 1,8 0,02 — — — — — — — — Rem. —
CuZn20Al2As CW702R 8,4
max. 79,0 2,3 0,06 — 0,07 0,1 0,1 0,01 0,05 — — — 0,3
min. 72,0 3,0 — 0,25 — — — — — — — Rem. —
CuZn23Al3Co CW703R 8,2
max. 75,0 3,8 — 0,55 0,05 — 0,3 — 0,05 — 0,1 — 0,1
min. 63,0 5,0 — — 2,0 3,5 — — 0,2 — — Rem. —
CuZn23Al6Mn4Fe3Pb CW704R 8,2
max. 65,0 6,0 — — 3,5 5,0 0,5 — 0,8 0,2 0,2 — 0,2
min. 65,0 4,0 — — 0,5 0,5 — — 0,2 — — Rem. —
CuZn25Al5Fe2Mn2Pb CW705R 8,2
max. 68,0 5,0 — — 3,0 3,0 1,0 — 0,8 — 0,2 — 0,3
min. 70,0 — 0,02 — — — — — — — 0,9 Rem. —
CuZn28Sn1As CW706R 8,5
max. 72,5 — 0,06 — 0,07 0,1 0,1 0,01 0,05 — 1,3 — 0,3
min. 69,0 — 0,02 — — — — — — — — Rem. —
CuZn30As CW707R 8,5
max. 71,0 0,02 0,06 — 0,05 0,1 — 0,01 0,07 — 0,05 — 0,3
min. 66,0 — — — — — — — — 0,7 — Rem. —
CuZn31Si1 CW708R 8,4
max. 70,0 — — — 0,4 — 0,5 — 0,8 1,3 — — 0,5
min. 64,0 — 0,03 — 0,1 — — — 1,5 0,45 — Rem. —
CuZn32Pb2AsFeSi CW709R 8,4
max. 66,5 0,05 0,08 — 0,2 — 0,3 — 2,2 0,8 0,3 — 0,2
min. 58,0 0,3 — — — 1,5 2,0 — 0,2 — — Rem. —
CuZn35Ni3Mn2AlPb CW710R 8,3
max. 60,0 1,3 — — 0,5 2,5 3,0 — 0,8 0,1 0,5 — 0,3
min. 59,5 — — — — — — — 1,3 — 0,5 Rem. —
CuZn36Pb2Sn1 CW711R 8,5
max. 61,5 — — — 0,1 — 0,3 — 2,2 — 1,0 — 0,2
min. 61,0 — — — — — — — 0,2 — 1,0 Rem. —
CuZn36Sn1Pb CW712R 8,3
max. 63,0 — — — 0,1 — 0,2 — 0,6 — 1,5 — 0,2
a
Density
Material designation Composition in % (mass fraction)
g/cm
Others
Symbol Number Element Cu Al As Co Fe Mn Ni P Pb Si Sn Zn
total approx.
min. 57,0 1,3 — — — 1,5 — — 0,2 0,3 — Rem. —
CuZn37Mn3Al2PbSi CW713R 8,1
max. 59,0 2,3 — — 1,0 3,0 1,0 — 0,8 1,3 0,4 — 0,3
min. 59,0 — — — — — — — 0,4 — 0,5 Rem. —
CuZn37Pb1Sn1 CW714R 8,4
max. 61,0 — — — 0,1 — 0,3 — 1,0 — 1,0 — 0,2
min. 59,0 0,1 — — 0,1 — 0,2 — 0,3 — 0,3 Rem. —
CuZn38AlFeNiPbSn CW715R 8,3
max. 60,7 0,5 0,05 — 0,4 — 0,5 — 0,7 — 0,6 — 0,2
min. 59,0 0,3 — — — 0,6 — — — — — Rem. —
CuZn38Mn1Al CW716R 8,3
max. 61,5 1,3 — — 1,0 1,8 0,6 — 1,0 0,5 0,3 — 0,3
min. 59,0 — 0,02 — — — — — — — 0,5 Rem. —
CuZn38Sn1As CW717R 8,4
max. 62,0 — 0,06 — 0,1 — 0,2 — 0,2 — 1,0 — 0,2
min. 57,0 0,3 — — — 0,8 — — 0,2 0,2 — Rem. —
CuZn39Mn1AlPbSi CW718R 8,2
max. 59,0 1,3 — — 0,5 1,8 0,5 — 0,8 0,8 0,5 — 0,3
min. 59,0 — — — — — — — — — 0,5 Rem. —
CuZn39Sn1 CW719R 8,4
max. 61,0 — — — 0,1 — 0,2 — 0,2 — 1,0 — 0,2
min. 57,0 — — — — 0,5 — — 1,0 — — Rem. —
CuZn40Mn1Pb1 CW720R 8,3
max. 59,0 0,2 — — 0,3 1,5 0,6 — 2,0 0,1 0,3 — 0,3
min. 57,0 0,3 — — 0,2 0,8 — — 0,8 — 0,2 Rem. —
CuZn40Mn1Pb1AlFeSn CW721R 8,3
max. 59,0 1,3 — — 1,2 1,8 0,3 — 1,6 — 1,0 — 0,3
min. 56,5 — — — 0,2 0,8 — — 0,8 — 0,2 Rem. —
CuZn40Mn1Pb1FeSn CW722R 8,3
max. 58,5 0,1 — — 1,2 1,8 0,3 — 1,6 — 1,0 — 0,3
min. 56,5 — — — 0,5 1,0 — — — — — Rem. —
CuZn40Mn2Fe1 CW723R 8,3
max. 58,5 0,1 — — 1,5 2,0 0,6 — 0,5 0,1 0,3 — 0,4
min. 75,0 — — — — — — 0,02 — 2,7 — Rem. —
CuZn21Si3P CW724R 8,3
max. 77,0 0,05 — — 0,3 0,05 0,2 0,10 0,10 3,5 0,3 — 0,2
min. 64,0 0,1 0,05 — — — — — 0,4 0,1 — Rem. —
CuZn33Pb1AlSiAs CW725R 8,5
max. 67,0 0,4 0,08 — 0,3 0,1 0,2 0,02 0,9 0,3 0,3 — 0,2
a
For information only.
Table 10 — Wrought coppers and copper alloys specified in European product Standards prepared by CEN/TC 133
Product forms and available materials
forging
Material designation
stock
rolled flat products tubes rod/bar, profiles, wire c
and
forgings
Coppers (see Tables 1.1 to 1.4)
Cu-ETP1 CW003A X X X
Cu-ETP CW004A X X X X X X X X X X X X
Cu-FRHC CW005A X X X X X X X
Cu-FRTP CW006A X
Cu-OF1 CW007A X X X
Cu-OF CW008A X X X X X X X X X X X X
Cu-OFE CW009A X X X X X
CuAg0,04 CW011A X X X
CuAg0,07 CW012A X X X
CuAg0,10 CW013A X X X X X
a
Symbol
b
Number
EN 1172:2011
E
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...