EN 14125:2004/A1:2006

Thermoplastic and flexible metal pipework for underground installation at petrol filling stations

This document specifies requirements for underground pipework systems used to transfer liquid fuels and their vapours at petrol filling stations. Minimum performance requirements covering fitness for purpose, safety and environmental protection are given.
This document applies to pipework made from thermoplastics, which may include some degree of reinforcement, and to flexible metal pipework. It does not apply to fibre reinforced thermosets, commonly referred to as glass fibre reinforced plastic (GRP), nor to rigid metals.
This document applies to:
-   delivery pipes from tanks to dispensers, including positive pressure, vacuum suction and siphon modes;
-   fill pipes from road tankers to tanks;
-   vapour recovery and vent pipework;
-   pipework for secondary containment;
-   connectors.
It does not apply to pipework for use with liquefied petroleum gas.

Thermoplastische und flexible metallene Rohrleitungen für erdverlegte Installationen für Tankstellen

Tuyauteries enterrées thermoplastiques et tuyauteries métalliques flexibles pour stations-service

Cevovodi iz kovinskih gibljivih cevi in cevi iz plastomerov za podzemne napeljave za bencinske servise - Dopolnilo A1

General Information

• Status: Withdrawn
• Publication Date: 31-Oct-2006
• Withdrawal Date: 18-Jun-2013
• ICS: 75.200 - Petroleum products and natural gas handling equipment
• Technical Committee: CEN/TC 393 - Equipment for storage tanks and for service stations
• Drafting Committee: CEN/TC 393/WG 6 - Underground pipework systems for petrol filling stations
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Start Date: 19-Jun-2013
• Completion Date: 19-Jun-2013
• Ref Project: SIST EN 14125:2005/A1:2007 - Thermoplastic and flexible metal pipework for underground installation at petrol filling stations

Relations

• Replaced By: EN 14125:2013 - Thermoplastic and flexible metal pipework for underground installation at petrol filling stations
• Effective Date: 26-Jun-2013
• Amends: EN 14125:2004 - Thermoplastic and flexible metal pipework for underground installation at petrol filling stations
• Effective Date: 08-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
01-marec-2007
Cevovodi iz kovinskih gibljivih cevi in cevi iz plastomerov za podzemne napeljave
za bencinske servise - Dopolnilo A1
Thermoplastic and flexible metal pipework for underground installation at petrol filling
stations
Thermoplastische und flexible metallene Rohrleitungen für erdverlegte Installationen für
Tankstellen
Tuyauteries enterrées thermoplastiques et tuyauteries métalliques flexibles pour stations
-service
Ta slovenski standard je istoveten z: EN 14125:2004/A1:2006
ICS:
23.040.10 Železne in jeklene cevi Iron and steel pipes
75.200 2SUHPD]DVNODGLãþHQMH Petroleum products and
QDIWHQDIWQLKSURL]YRGRYLQ natural gas handling
]HPHOMVNHJDSOLQD equipment
83.140.30 Cevi, fitingi in ventili iz Plastics pipes, fittings and
polimernih materialov valves
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD
EN 14125:2004/A1
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2006
ICS 75.200
English Version
Thermoplastic and flexible metal pipework for underground
installation at petrol filling stations
Tuyauteries enterrées thermoplastiques et tuyauteries Thermoplastische und flexible metallene Rohrleitungen für
métalliques flexibles pour stations-service erdverlegte Installationen für Tankstellen
This amendment A1 modifies the European Standard EN 14125:2004; it was approved by CEN on 28 September 2006.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references concerning such
national standards may be obtained on application to the Central Secretariat or to any CEN member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 14125:2004/A1:2006: E
worldwide for CEN national Members.

Foreword
This document (EN 14125:2004/A1:2006) has been prepared by Technical Committee CEN/TC 221 “Shop
fabricated metallic tanks and equipment for storage tanks and for service stations”, the secretariat of which is
held by DIN.
This Amendment to the European Standard EN 14125:2004 shall be given the status of a national standard,
either by publicatio
...