Plastics welding personnel - Qualification testing of welders - Thermoplastics welded assemblies

This European Standard specifies the method of testing the knowledge and skill of a welder who is required to carry out welds on thermoplastics in new constructions and repair work.
The skill examination of a welder is an essential condition for the assurance of the quality of the welding work.
The application of this standard guarantees that the examination is carried out according to a uniform test procedure.
This European Standard applies when the contractor or the authorities responsible for the application require it.
Gas and water utility network industries with alternative qualification programmes are excluded from this standard.
This European Standard applies to the following welding processes:
- hot gas welding: round nozzle, high speed nozzle, wedge;
- extrusion welding;
- heated tool welding: butt, saddle, socket, wedge;
- electrofusion welding: socket, saddle;
- solvent welding: socket.
This European Standard applies to the welding of the following products:
- sheet;
- pipe;
- fittings;
- lining membrane.
This European Standard covers the welding of the following groups of materials:
a)   for sheets, pipes and fittings:
1)   group 1: PVC (including all kinds of PVC-U, PVC-C), ABS;
2)   group 2: PP (including all kinds of PP);
3)   group 3: PE (including all kinds of PE);
4)   group 4: PVDF;
5)   group 5: ECTFE or PFA or FEP;
b)   for lining membranes:
1)   group 6: PVC-P;
2)   group 7: PE (including all kinds of PE);
3)   group 8: ECB;
4)   group 9: PP.

Kunststoffschweißpersonal - Anerkennungsprüfung von Schweißern - Thermoplastische Schweißverbindungen

Diese europäische Norm legt Verfahren für die Prüfung der Kenntnisse und Fertigkeiten eines Schweißers fest, der Schweißarbeiten an Thermoplasten bei Neuanfertigungen und Reparaturarbeiten durchzuführen hat.
Die Prüfung der Fertigkeiten eines Schweißers ist eine notwendige Bedingung für die Sicherung der Qualität bei Schweißarbeiten.
Die Anwendung dieser Norm stellt sicher, dass die Prüfung nach einem einheitlichen Prüfverfahren durchgeführt wird.
Diese europäische Norm findet Anwendung, wenn der Auftragnehmer oder die für das Anwendungsgebiet verantwortliche Behörde dies fordert.
Gas  und Wasserversorgungsunternehmen, die alternative Anerkennungsprogramme haben, sind von dieser Norm ausgeschlossen.
Diese europäische Norm gilt für folgende Schweißverfahren:
   Warmgasschweißen: Runddüse, Schnellschweißdüse, Keil;
   Extrusionsschweißen;
   Heizelementstumpfschweißen: Stumpfstoß, Sattel, Muffe, Keil;
   Heizwendelschweißen: Muffe, Sattel;
   Quellschweißen: Muffe.
Diese europäische Norm gilt für das Schweißen folgender Produkte:
   Tafeln;
   Rohre;
   Formstücke;
   Dichtungsbahnen.
Diese europäische Norm gilt für das Schweißen der folgenden Werkstoffgruppen:
a)   für Tafeln, Rohre und Formstücke:
   Gruppe 1: PVC (einschließlich aller Typen von PVC U, PVC C), ABS;
   Gruppe 2: PP (einschließlich aller Typen von PP);
   Gruppe 3: PE (einschließlich aller Typen von PE);
   Gruppe 4: PVDF;
   Gruppe 5: ECTFE oder PFA oder FEP.
b)   für Dichtungsbahnen:
   Gruppe 6: PVC P;
   Gruppe 7: PE (einschließlich aller Typen von PE);
   Gruppe 8: ECB;
   Gruppe 9: PP.

Personnel en soudage des plastiques - Épreuve de qualification des soudeurs - Assemblages soudés thermoplastiques

La présente Norme européenne spécifie la méthode à utiliser pour évaluer les connaissances et l'habileté d'un soudeur à qui il est demandé de réaliser des soudures sur des matières thermoplastiques pour des constructions neuves et des travaux de réparation.
L'examen de l'habileté d'un soudeur est une condition essentielle de l'assurance de la qualité du soudage.
L'application de la présente norme garantit que l'examen se déroule selon une procédure d'épreuve uniforme.
La présente Norme européenne s'applique lorsque le contractant ou les autorités responsables de l'application l'exigent.
Les sociétés de distribution publique de gaz et d'eau qui disposent de programmes de qualification différents ne sont pas concernées par la présente norme.
La présente Norme européenne s'applique aux procédés de soudage suivants :
   soudage au gaz chaud : buse ronde, buse rapide, coin chauffant ;
   soudage par extrusion ;
   soudage par élément chauffant : bout à bout, selle de raccordement, emboîture, coin chauffant ;
   soudage par électrofusion : emboîture, selle de raccordement ;
   soudage par solvant : emboîture.
La présente Norme européenne s'applique au soudage des produits suivants :
   feuilles/plaques ;
   tubes ;
   raccords ;
   membranes de revêtement.
La présente Norme européenne couvre le soudage des groupes de matériaux suivants :
a)   pour les feuilles, tubes et raccords :
   groupe 1 : PVC (incluant tous les types de PVC-U, PVC-C, ABS) ;
   groupe 2 : PP (incluant tous les types de PP) ;
   groupe 3 : PE (incluant tous les types de PE, PB) ;
   groupe 4 : PVDF ;
   groupe 5 : ECTFE, PFA ou FEP ;
b)   pour les membranes de revêtement :
   groupe 6 : PVC-P ;
   groupe 7 : PE (incluant tous les types de PE) ;
   groupe 8 : ECB ;
   groupe 9 : PP.

Osebje za varjenje polimerov - Preskušanje usposobljenosti varilcev - Varjenje plastomerov

Ta evropski standard določa metodo preskušanja znanja in veščin varilcev za varjenje plastomerov v novih konstrukcijah in v okviru popravil. Preskus veščin varilcev je osnovni pogoj za zagotavljanje kakovosti varjenja. Uporaba tega standarda zagotavlja, da je preskus izveden v skladu z enotnim preskusnim postopkom. Ta evropski standard se uporablja, kadar ga potrebujejo izvajalec ali organi, odgovorni za njegovo uporabo. Panoge oskrbe s plinom in vodo, ki imajo alternativne programe usposabljanj, niso zajete v tem standardu. Ta evropski standard se uporablja za naslednje postopke varjenja: – varjenje z vročim zrakom: okrogla šoba, šoba za varjenje z visoko hitrostjo, klini; – ekstrudersko varjenje; – varjenje z vročimi ploščami: soležni zvari, sedla, obojni zvari, klini; – elektrofuzijsko varjenje: obojni zvari, sedla; – varjenje s topilom: obojni zvari. Ta evropski standard se uporablja za varjenje naslednjih izdelkov: – plošče; – cevi; – spojniki; – obložne membrane. Ta evropski standard zajema varjenje naslednjih skupin materialov: a) za plošče, cevi in spojnike: 1) skupina 1: PVC (vključuje vse vrste PVC-U, PVC-C), ABS; 2) skupina 2: PP (vključuje vse vrste PP); 3) skupina 3: PE (vključuje vse vrste PE); 4) skupina 4: PVDF; 5) skupina 5: ECTFE ali PFA ali FEP; b) za obložne membrane: 1) skupina 6: PVC-P; 2) skupina 7: PE (vključuje vse vrste PE); 3) skupina 8: ECB; 4) skupina 9: PP.

General Information

Status
Withdrawn
Publication Date
06-Nov-2012
Withdrawal Date
01-Sep-2020
Current Stage
9960 - Withdrawal effective - Withdrawal
Completion Date
02-Sep-2020

Relations

Buy Standard

Standard
EN 13067:2014
English language
42 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Osebje za varjenje polimerov - Preskušanje usposobljenosti varilcev - Varjenje plastomerovKunststoffschweißpersonal - Anerkennungsprüfung von Schweißern - Thermoplastische SchweißverbindungenPersonnel en soudage des plastiques - Épreuve de qualification des soudeurs - Assemblages soudés thermoplastiquesPlastics welding personnel - Qualification testing of welders - Thermoplastics welded assemblies83.080.20PlastomeriThermoplastic materials25.160.01Varjenje, trdo in mehko spajkanje na splošnoWelding, brazing and soldering in general03.100.30Vodenje ljudiManagement of human resourcesICS:Ta slovenski standard je istoveten z:EN 13067:2012SIST EN 13067:2014en,fr,de01-maj-2014SIST EN 13067:2014SLOVENSKI
STANDARDSIST EN 13067:20031DGRPHãþD



SIST EN 13067:2014



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13067
November 2012 ICS 03.100.30; 25.160.10 Supersedes EN 13067:2003English Version
Plastics welding personnel - Qualification testing of welders - Thermoplastics welded assemblies
Personnel en soudage des plastiques - Épreuve de qualification des soudeurs - Assemblages soudés thermoplastiques
Kunststoffschweißpersonal - Anerkennungsprüfung von Schweißern - Thermoplastische Schweißverbindungen This European Standard was approved by CEN on 22 September 2012.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13067:2012: ESIST EN 13067:2014



EN 13067:2012 (E) 2 Contents Page Foreword . 3Introduction . 41Scope . 52Normative references . 63Terms and definitions . 64Admission to the qualification tests . 85Testing of skill and knowledge . 96Duty of Plastics Welding Examiner and invigilator. 167Range of qualification . 168Welding of test piece . 169Test piece and test specimens, shapes and dimensions . 1610Evaluation and acceptance criteria of test piece(s) and test specimens . 2411Test result and qualification test certificate . 2812Failed test . 2913Period of validity .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.