Plain bearings - Aluminium alloys for solid bearings

ISO 6279:2017 specifies the composition and properties of preferred cast aluminium alloys for use in solid plain bearings. Other alloys can be specified with agreement between the manufacturer and user.

Paliers lisses - Alliages d'aluminium pour paliers massifs

Drsni ležaji - Aluminijeve zlitine za masivne ležaje

General Information

Status
Published
Publication Date
19-Jul-2020
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
09-Jun-2020
Due Date
14-Aug-2020
Completion Date
20-Jul-2020

Relations

Buy Standard

Standard
ISO 6279:2020
English language
6 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Standard
ISO 6279:2017 - Plain bearings -- Aluminium alloys for solid bearings
English language
2 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

SLOVENSKI STANDARD
SIST ISO 6279:2020
01-september-2020
Drsni ležaji - Aluminijeve zlitine za masivne ležaje
Plain bearings - Aluminium alloys for solid bearings
Paliers lisses - Alliages d'aluminium pour paliers massifs
Ta slovenski standard je istoveten z: ISO 6279:2017
ICS:
21.100.10 Drsni ležaji Plain bearings
77.150.10 Aluminijski izdelki Aluminium products
SIST ISO 6279:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST ISO 6279:2020

---------------------- Page: 2 ----------------------
SIST ISO 6279:2020
INTERNATIONAL ISO
STANDARD 6279
Third edition
2017-03
Plain bearings — Aluminium alloys for
solid bearings
Paliers lisses — Alliages d’aluminium pour paliers massifs
Reference number
ISO 6279:2017(E)
©
ISO 2017

---------------------- Page: 3 ----------------------
SIST ISO 6279:2020
ISO 6279:2017(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved

---------------------- Page: 4 ----------------------
SIST ISO 6279:2020
ISO 6279:2017(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Composition and mechanical properties . 1
4.1 Composition . 1
4.2 Mechanical properties . 1
5 Test methods . 1
6 Designation . 2
© ISO 2017 – All rights reserved iii

---------------------- Page: 5 ----------------------
SIST ISO 6279:2020
ISO 6279:2017(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not b
...

INTERNATIONAL ISO
STANDARD 6279
Third edition
2017-03
Plain bearings — Aluminium alloys for
solid bearings
Paliers lisses — Alliages d’aluminium pour paliers massifs
Reference number
ISO 6279:2017(E)
©
ISO 2017

---------------------- Page: 1 ----------------------
ISO 6279:2017(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 6279:2017(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Composition and mechanical properties . 1
4.1 Composition . 1
4.2 Mechanical properties . 1
5 Test methods . 1
6 Designation . 2
© ISO 2017 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 6279:2017(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the vo
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.