SIST EN ISO 8092-2:2004
(Main)Road vehicles - Connections for on-board electrical wiring harnesses - Part 2: Definitions, test methods and general performance requirements (ISO 8092-2:2000)
Road vehicles - Connections for on-board electrical wiring harnesses - Part 2: Definitions, test methods and general performance requirements (ISO 8092-2:2000)
Straßenfahrzeuge - Steckverbindungen für das elektrische Fahrzeug-Bordnetz - Teil 2: Begriffe, Prüfungen und allgemeine Anforderungen (ISO 8092-2:2000)
Dieser Teil von ISO 8092 definiert Begriffe und legt Prüfmethoden und allgemeine Anforderungen an ein- und mehrpolige Steckverbindungen fest, die in elektrischen Bordnetze von Straßenfahrzeugen verwendet werden.
Dieser Teil von ISO 8092 ist auf Steckverbinder anwendbar, die nach der Montage im Fahrzeug nur ausschließlich im Reparaturfall und/oder beim Kundendienst getrennt zu werden. Er schließt einteilige Steckverbindungen nicht ein, d. h. wobei ein Teil der Steckverbindung direkten Kontakt mit den Leiterbahnen gedruckter Schaltungen hat.
Dieser Teil von ISO 8092 gilt nicht für Steckverbindungen in elektronischen Geräten.
Véhicules routiers - Connexions pour faisceaux de câblage électrique embarqués - Partie 2: Définitions, méthodes d'essai et exigences générales (ISO 8092-2:2000)
Cestna vozila - Priključki za električno opremo, vgrajeni na armaturi vozila - 2. del: Definicije, preskusne metode in splošne zahtevane lastnosti (ISO 8092-2:2000)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2004
&HVWQDYR]LOD3ULNOMXþNL]DHOHNWULþQRRSUHPRYJUDMHQLQDDUPDWXULYR]LODGHO
'HILQLFLMHSUHVNXVQHPHWRGHLQVSORãQH]DKWHYDQHODVWQRVWL,62
Road vehicles - Connections for on-board electrical wiring harnesses - Part 2:
Definitions, test methods and general performance requirements (ISO 8092-2:2000)
Straßenfahrzeuge - Steckverbindungen für das elektrische Fahrzeug-Bordnetz - Teil 2:
Begriffe, Prüfungen und allgemeine Anforderungen (ISO 8092-2:2000)
Véhicules routiers - Connexions pour faisceaux de câblage électrique embarqués -
Partie 2: Définitions, méthodes d'essai et exigences générales (ISO 8092-2:2000)
Ta slovenski standard je istoveten z: EN ISO 8092-2:2001
ICS:
43.040.10 (OHNWULþQDLQHOHNWURQVND Electrical and electronic
RSUHPD equipment
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 8092-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2001
ICS 43.040.10 Supersedes EN 28092-2:1998
English version
Road vehicles - Connections for on-board electrical wiring
harnesses - Part 2: Definitions, test methods and general
performance requirements (ISO 8092-2:2000)
Véhicules routiers - Connexions pour faisceaux de câblage Straßenfahrzeuge - Steckverbindungen für das elektrische
électrique embarqués - Partie 2: Définitions, méthodes Fahrzeug-Bordnetz - Teil 2: Begriffe, Prüfungen und
d'essai et exigences générales (ISO 8092-2:2000) allgemeine Anforderungen (ISO 8092-2:2000)
This European Standard was approved by CEN on 17 November 2001.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,
Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2001 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 8092-2:2001 E
worldwide for CEN national Members.
CORRECTED 2002-11-14
Foreword
The text of ISO 8092-2:2000 has been prepared by Technical Committee ISO/TC 22 "Road
vehicles" of the International Organization for Standardization (ISO) and has been taken over as
This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by June 2002, and conflicting national
standards shall be withdrawn at the latest by June 2002.
This document supersedes EN 28092-2:1998.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium, Czech
Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg,
Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 8092-2:2000 has been approved by CEN as EN ISO 8092-2:2001 without any
modifications.
INTERNATIONAL ISO
STANDARD 8092-2
Third edition
2000-12-15
Corrected and reprinted
2002-01-15
Road vehicles — Connections for on-board
electrical wiring harnesses —
Part 2:
Definitions, test methods and general
performance requirements
Véhicules routiers — Connexions pour faisceaux de câblage électrique
embarqués —
Partie 2: Définitions, méthodes d'essai et exigences générales
Reference number
ISO 8092-2:2000(E)
©
ISO 2000
ISO 8092-2:2000(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 2000 – All rights reserved
ISO 8092-2:2000(E)
Contents Page
Foreword.iv
1 Scope .1
2 Normative references .1
3 Terms and definitions .2
4 Tests and requirements .5
4.1 General.5
4.2 Visual examination .7
4.3 Connection and disconnection .7
4.4 Tensile strength of conductor-to-contact attachment.8
4.5 Locking device strength .8
4.6 Contact insertion force .9
4.7 Contact retention in housing.10
4.8 Connection resistance (voltage drop) .10
4.9 Influence of water .11
4.10 Temperature/humidity cycling.15
4.11 Combined temperature and vibration.17
4.12 Insulation resistance .19
4.13 Withstand voltage.19
4.14 Temperature rise.20
4.15 Connector coding and polarization .21
4.16 Salt spray.21
4.17 Current cycling.21
4.18 Thermal ageing .22
4.19 Mechanical shock .22
4.20 Drop.22
4.21 Dust .23
4.22 Rapid change of temperature (thermal shock).24
4.23 Chemical fluids .24
4.24 Flowing gas corrosion .25
Annex A (informative) Flowing single-gas corrosion test.26
Annex B (informative) Cable attachment by insulation-displacement connection (IDC) — Tensile
strength test .28
Bibliography.30
ISO 8092-2:2000(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this part of ISO 8092 may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 8092-2 was prepared by Technical Committee ISO/TC 22, Road vehicles,
Subcommittee SC 3, Electrical and electronic equipment.
This third edition cancels and replaces the second edition (ISO 8092-2:1996), which has been technically revised.
ISO 8092 consists of the following parts, under the general title Road vehicles — Connections for on-board
electrical wiring harnesses:
— Part 1: Tabs for single-pole connections — Dimensions and specific requirements
— Part 2: Definitions, test methods and general performance requirements
— Part 3: Tabs for multi-pole connections — Dimensions and specific requirements
— Part 4: Pins for single- and multi-pole connections — Dimensions and specific requirements
Annexes A and B of this part of ISO 8092 are for information only.
iv © ISO 2000 – All rights reserved
INTERNATIONAL STANDARD ISO 8092-2:2000(E)
Road vehicles — Connections for on-board electrical wiring
harnesses —
Part 2:
Definitions, test methods and general performance requirements
1 Scope
This part of ISO 8092 defines terms and specifies test methods and general performance requirements for single-
and multi-pole connections used with on-board electrical wiring harnesses in road vehicles.
This part of ISO 8092 is applicable to connectors designed to be disconnected after mounting in the vehicle for
repair and maintenance only. It does not cover one-part connections, i.e. where one part of the connection has
direct contact with the pattern of the printed circuit board.
This part of ISO 8092 is not applicable to the internal connections of electronic devices.
2 Normative references
The following normative documents contain provisions which, through reference in this text, constitute provisions of
this part of ISO 8092. For dated references, subsequent amendments to, or revisions of, any of these publications
do not apply. However, parties to agreements based on this part of ISO 8092 are encouraged to investigate the
possibility of applying the most recent editions of the normative documents indicated below. For undated
references, the latest edition of the normative document referred
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.