SIST EN ISO 15614-13:2005

Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 13: Resistance butt and flash welding (ISO 15614-13:2005)

This standard specifies the tests which may be used for qualification of welding procedure specifications.
This standard is a part of a series of standards. Details of this series are given in prEN ISO 15607, Annex A.
It defines the conditions for carrying out tests and the limits of validity of an qualified welding procedure for all practical welding operations covered by this standard.
The tests required to qualify the procedure for a particular component/assembly depend on the performance and quality requirements of the component/assembly and should be defined in the specification.
The tests should be carried out in accordance with this standard, unless more severe tests are specified by the relevant application standard or specification, when these should apply.
This standard applies to resistance butt welding and flash welding of metallic materials, e. g. with solids, tubular, flat, round cross section. The basic principles of this standard may be applied to other resistance welding processes when this is specified in the specification.
NOTE: Specific service, material, or manufacturing conditions may require more comprehensive testing than is specified by this standard.

Anforderung und Qualifizierung von Schweißverfahren für metallische Werkstoffe - Schweißverfahrensprüfung - Teil 13: Pressstumpf- und Abbrennstumpfschweißen (ISO 15614-13:2005)

Dieser Teil der ISO 15614 legt die Prüfungen fest, die zur Qualifizierung von Schweißanweisungen angewendet werden dürfen.
Dieser Teil der ISO 15614 ist für das Pressstumpfschweißen und für das Abbrennstumpfschweißen von metallischen Werkstoffen anzuwenden, z. B. bei vollen, rohrförmigen, flachen oder runden Querschnitten. Die Grundprinzipien dieses Teiles der ISO 15614 dürfen für andere Widerstandsschweißprozesse angewendet werden, wenn dieses in der Konstruktionsbeschreibung festgelegt wird.
ANMERKUNG   Dieser Teil der ISO 15614 gehört zu einer Normenreihe. EN ISO 15607:2003, Anhang A, gibt Einzelheiten dieser Normenreihe wieder.
Dieser Teil der ISO 15614 legt die Bedingungen für die Ausführung der Prüfungen und die Grenzen der Gültigkeit eines qualifizierten Schweißverfahrens für alle in der Praxis angewendeten Schweißverfahren fest, die durch diesen Teil der ISO 15614 abgedeckt sind.
Die Prüfungen, die erforderlich sind, um das Schweißverfahren für ein(e) bestimmte(s) Bauteil/Baugruppe zu qualifizieren, hängen von der Ausführung und den Qualitätsanforderungen an das Bauteil/an die Baugruppe ab und sollten in der Konstruktionsbeschreibung festgelegt werden.
Die Prüfungen sollten in Übereinstimmung mit diesem Teil der ISO 15614 ausgeführt werden, wenn keine besonderen Prüfungen nach der entsprechenden Anwendungsnorm oder Konstruktionsbeschreibung anzuwenden sind.
ANMERKUNG   Spezielle Aufgaben, Werkstoffe oder Herstellungsbedingungen dürfen umfangreichere als in diesem Teil der ISO 15614 festgelegte Prüfungen erfordern.
Derartige Prüfungen dürfen einschließen:
-   Mikroschliffe;
-   Ermüdungs- oder Dauerprüfungen;
-   Schlagprüfung;
-   Durchstrahlungsprüfung;
-   Ultraschallprüfung;
-   Korrosionsprüfung;
-   Prüfung der Bauteile oder der gesamten geschweißten Baugruppe.
Dieser Teil der ISO 15614 bezieht sich auf die folgenden Widerstandsschweißprozesse, die in ISO 4063 definiert sind:
-   24 - Abbrennstumpfschweißen bei Verwendung von Gleich- oder Wechselstrom mit v

Descriptif et qualification d'un mode opératoire de soudage pour les matériaux métalliques - Epreuve de qualification d'un mode opératoire de soudage - Partie 13: Soudage en bout par résistance pure et soudage par étincelage (ISO 15614-13:2005)

L'ISO 15614-13:2005 spécifie les épreuves pouvant être utilisées pour qualifier un descriptif de mode opératoire de soudage.
Elle s'applique au soudage en bout par résistance pure et au soudage par étincelage des matériaux métalliques, par exemple des sections droites pleines ou tubulaires, plates ou circulaires. Les principes de base de l'ISO 15614-13:2005 peuvent être appliqués à d'autres procédés de soudage par résistance lorsque la spécification le spécifie.
L'ISO 15614-13:2005 définit les conditions d'exécution des épreuves de qualification et les limites de validité d'un mode opératoire qualifié, pour toutes les opérations pratiques de soudage concernées par l'ISO 15614-13:2005.
L'ISO 15614-13:2005 traite des procédés de soudage par résistance suivants, tels que définis dans l'ISO 4063:
24 soudage par étincelage en courant continu ou en courant alternatif avec diverses séquences de mouvement, étincelage continu et étincelage intermittent;
25 soudage en bout par résistance pure, en courant continu ou en courant alternatif avec diverses séquences d'effort.

Popis in kvalifikacija varilnih postopkov za kovinske materiale - Preskus varilnega postopka - 13. del: Uporovno sočelno in obžigalno varjenje (ISO 15614-13:2005)

General Information

• Status: Withdrawn
• Publication Date: 30-Apr-2005
• Withdrawal Date: 12-Jul-2012
• ICS: 25.160.10 - Welding processes
• Technical Committee: VAR - Welding
• Current Stage: 9900 - Withdrawal (Adopted Project)
• Start Date: 12-Jul-2012
• Due Date: 04-Aug-2012
• Completion Date: 13-Jul-2012
• Ref Project: EN ISO 15614-13:2005 - Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 13: Resistance butt and flash welding (ISO 15614-13:2005)

Relations

• Replaced By: SIST EN ISO 15614-13:2012 - Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 13: Upset (resistance butt) and flash welding (ISO 15614-13:2012)
• Effective Date: 01-Sep-2012

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 15614-13:2005
01-maj-2005
3RSLVLQNYDOLILNDFLMDYDULOQLKSRVWRSNRY]DNRYLQVNHPDWHULDOH3UHVNXVYDULOQHJD
SRVWRSNDGHO8SRURYQRVRþHOQRLQREåLJDOQRYDUMHQMH,62
Specification and qualification of welding procedures for metallic materials - Welding
procedure test - Part 13: Resistance butt and flash welding (ISO 15614-13:2005)
Anforderung und Qualifizierung von Schweißverfahren für metallische Werkstoffe -
Schweißverfahrensprüfung - Teil 13: Pressstumpf- und Abbrennstumpfschweißen (ISO
15614-13:2005)
Descriptif et qualification d'un mode opératoire de soudage pour les matériaux
métalliques - Epreuve de qualification d'un mode opératoire de soudage - Partie 13:
Soudage en bout par résistance pure et soudage par étincelage (ISO 15614-13:2005)
Ta slovenski standard je istoveten z: EN ISO 15614-13:2005
ICS:
25.160.10 Varilni postopki in varjenje Welding processes
SIST EN ISO 15614-13:2005 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 15614-13:2005

---------------------- Page: 2 ----------------------

SIST EN ISO 15614-13:2005
EUROPEAN STANDARD
EN ISO 15614-13
NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2005
ICS 25.160.10
English version
Specification and qualification of welding procedures for metallic
materials - Welding procedure test - Part 13: Resistance butt
and flash welding (ISO 15614-13:2005)
Descriptif et qualification d'un mode opératoire de soudage Anforderung und Qualifizierung von Schweißverfahren für
pour les matériaux métalliques - Epreuve de qualification metallische Werkstoffe - Schweißverfahrensprüfung - Teil
d'un mode opératoire de soudage - Partie 13: Soudage en 13: Pressstumpf- und Abbrennstumpfschweißen (ISO
bout par résistance pure et soudage par étincelage (ISO 15614-13:2005)
15614-13:2005)
This European Standard was approved by CEN on 3 February 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15614-13:2005: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 15614-13:2005
EN ISO 15614-13:2005 (E)




Foreword



This document (EN ISO 15614-13:2005) has been prepared by Technical Committee CEN/TC 121
"Welding", the secretariat of which is held by DIN, in collaboration with Technical Committee ISO/TC 44
"Welding and allied processes".

This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by August 2005, and conflicting national standards shall be withdrawn
at the latest by August 2005.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland
and United Kingdom.

2

---------------------- Page: 4 ----------------------

SIST EN ISO 15614-13:2005

INTERNATIONAL ISO
STANDARD 15614-13
First edition
2005-02-15


Specification and qualification of welding
procedures for metallic materials —
Welding procedure test —
Part 13:
Resistance butt and flash welding
Descriptif et qualification d'un mode opératoire de soudage pour les
matériaux métalliques — Épreuve de qualification d'un mode opératoire
de soudage —
Partie 13: Soudage en bout par résistance pure et soudage par
étincelage





Reference number
ISO 15614-13:2005(E)
©
ISO 2005

---------------------- Page: 5 ----------------------

SIST EN ISO 15614-13:2005
ISO 15614-13:2005(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2005
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [e-mail]
Web www.iso.org
Published in Switzerland

ii © ISO 2005 – All rights reserved

---------------------- Page: 6 ----------------------

SIST EN ISO 15614-13:2005
ISO 15614-13:2005(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope. 1
2 Normative references. 2
3 Terms and definitions. 3
4 Preliminary welding procedure specification (pWPS) . 3
5 Welding procedure test . 3
6 Test piece and test specimen . 3
6.1 General. 3
6.2 Shape and dimensions of test specimens . 4
6.3 Welding of components, test pieces or test specimens. 5
7 Testing and examination. 5
7.1 Extent of testing . 5
7.2 Non-destructive testing. 5
7.3 Destructive tests. 6
7.4 Macrosection. 6
7.5 Hardness distribution. 6
7.6 Re-testing. 6
8 Range of qualification. 7
8.1 General. 7
8.2 Related to the manufacturer . 7
8.3 Related to the parent metal. 7
8.4 Welding procedures. 7
8.5 Test certificate. 7
9 Welding procedure qualification record (WPQR) . 7
Annex A (informative) Example of welding procedure qualification — Test certificate . 8
Annex B (informative) Example of welding procedure qualifications record form (WPQR). 10


© ISO 2005 – All rights reserved iii

---------------------- Page: 7 ----------------------

SIST EN ISO 15614-13:2005
ISO 15614-13:2005(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 15614-13 was prepared by the European Committee for Standardization (CEN) Technical Committee
CEN/TC 121, Welding, in collaboration with Technical Committee ISO/TC 44, Welding and allied processes,
Subcommittee SC 10, Unification of requirements in the field of metal welding, in accordance with the
Agreement on Technical cooperation between ISO and CEN (Vienna Agreement).
ISO 15614 consists of the following parts, under the general title Specification and qualification of welding
procedures for metallic materials — Welding procedure test:
 Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys
 Part 2: Arc welding of aluminium and its alloys
 Part 3: Arc welding of cast iron
 Part 4: Finishing welding of aluminium castings
 Part 5: Arc welding of titanium, zirconium and their alloys
 Part 6: Arc welding of copper and its alloys
 Part 7: Overlay welding
 Part 8: Welding of tubes to tube-plate joints
 Part 9: Arc underwater hyperbaric wet welding
 Part 10: Hyperbaric dry welding:
 Part 11: Electron and laser beam welding
 Part 12: Spot, seam and projection welding
 Part 13: Resistance butt and flash welding
For the purposes of this part of ISO 15614, the CEN annex regarding fulfilment of European Council
Directives has been removed.
iv © ISO 2005 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 15614-13:2005
ISO 15614-13:2005(E)
Introduction
All new welding procedure qualifications are to be carried out in accordance with this part of ISO 15614 from
the date of its issue.
However, this part of ISO 15614 does not invalidate previous welding procedure qualifications made to
standards or specifications, provided the intent of the technical requirements is satisfied and the previous
welding procedure qualifications are relevant to the application and production work on which they are to be
employed.
Also, where additional tests have to be carried out to make the qualification technically equivalent, it is only
necessary to do the additional tests on a test piece which should be made in accordance with this part of
ISO 15614.
Requests for official interpretations of any aspect of this part of ISO 15614 should be directed to the
Secretariat of ISO/TC 44/SC 10 via the national standards body, a complete listing of which can be found at
www.iso.org.

© ISO 2005 – All rights reserved v

---------------------- Page: 9 ----------------------

SIST EN ISO 15614-13:2005

---------------------- Page: 10 ----------------------

SIST EN ISO 15614-13:2005
INTERNATIONAL STANDARD ISO 15614-13:2005(E)

Specification and qualification of welding procedures for
metallic materials — Welding procedure test —
Part 13:
Resistance butt and flash welding
1 Scope
This part of ISO 15614 specifies the tests which should be used for qualification of welding procedure
specifications.
It applies to resistance butt welding and flash welding of metallic materials, e.g. with solid, tubular, flat or
circular cross-section. The basic principles of this part of ISO 15614 may be applied to other resistance
welding processes when this is specified in the specification.
NOTE This part of ISO 15614 is a part of a series of standards. Details of this series are given in ISO 15607:2003,
Annex A.
This part of ISO 15614 defines the conditions for carrying out tests and the limits of validity of a qualified
welding procedure for all practical welding operations covered by this part of ISO 15614.
The tests required to qualify the procedure for a particular component/assembly depend on the performance
and quality requirements of the component/assembly and should be defined in the design specification.
The tests should be carried out in accordance with this part of ISO 15614, unless more severe tests are
specified by the relevant application standard or specification, when these apply.
NOTE Specific service, material, or manufacturing conditions may require more comprehensive testing than is
specified by this part of ISO 15614.
Such tests may include:
 microsections;
 fatigue or endurance tests;
 impact test;
 radiographic test;
 ultrasonic test;
 corrosion test;
 tests of components or complete welded assemblies.
This part of ISO 15614 covers the following resistance welding processes as defined in ISO 4063:
 24 flash welding, using direct current or alternating current with various movement sequences, constant
flashing and pulsed flashing;
 25 resistance butt welding, using direct current or alternating current with various pressure sequences.
© ISO 2005 – All rights reserved 1

---------------------- Page: 11 ----------------------

SIST EN ISO 15614-13:2005
ISO 15614-13:2005(E)
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
EN 1289, Non-destructive examination of welds — Penetrant testing of welds — Acceptance levels
EN 1291, Non-destructive examination of welds — Magnetic particle testing of welds — Acceptance levels
EN 1418, Welding personnel — Approval testing of welding operators for fusion welding and resistance weld
setters for fully mechanized and automatic welding of metallic materials
EN 1711, Non-destructive examination of welds — Eddy current examination of welds by complex plane
analysis
EN 1712, Non-destructive examination of welds — Ultrasonic examination of welded joints — Acceptance
levels
EN 1713, Non-destructive examination of welds — Ultrasonic examination — Characterization of indications in
welds
ISO 4063, Welding and allied processes — Nomenclature of processes and reference numbers
1)
ISO 4136 , Destructive tests on welds in metallic materials — Transverse tensile test
2)
ISO 5173 , Destructive tests on welds in metallic materials — Bend tests
ISO 6520-2, Welding and allied processes — Classification of geometric imperfections in metallic materials —
Part 2: Welding with pressure
3)
ISO 9015-1 , Destructive tests on welds in metallic materials — Hardness testing — Part 1: Hardness test on
arc welded joints
4)
ISO 9015-2 , Destructive tests on welds in metallic materials — Hardness testing — Part 2: Microhardness
testing of welded joints
EN 10002-1, Metallic materials — Tensile testing — Part 1: Method of test at ambient temperature
ISO 14271, Vickers hardness testing of resistance spot, projection and seam welds (low load and
microhardness)
ISO 15607:2003, Specification and qualification of welding procedures for metallic materials — General rules
ISO/TR 15608:2000, Welding — Guidelines for a metallic materials grouping system

1) Standard equivalent to EN 895.
2) Standard equivalent to EN 910.
3) Standard equivalent to EN 1043-1.
4) Standard equivalent to EN 1043-2.
2 © ISO 2005 – All rights reserved

---------------------- Page: 12 ----------------------

SIST EN ISO 15614-13:2005
ISO 15614-13:2005(E)
ISO 15609-5, Specification and qualification of welding procedures for metallic materials — Welding
procedure specification — Part 5: Resistance welding
ISO 15620:2000, Welding — Friction welding of metallic materials
5)
ISO 17637 , Non-de
...