Resistance welding - Vocabulary - Part 1: Spot, projection and seam welding (ISO 17677-1:2019)

This document establishes
a vocabulary of terms and
definitions for resistance spot
welding, projection welding and
seam welding.
NOTE In addition to terms
used in English and French, two
of the three official ISO languages,
this document gives the equivalent
terms in German; these are
published under the responsibility
of the member body for Germany
(DIN). However, only the terms
and definitions given in the official
languages can be considered as ISO
terms and definitions.

Widerstandsschweißen - Begriffe - Teil 1: Punkt-, Buckel- und Rollennahtschweißen (ISO 17677-1:2019)

Dieser Teil von ISO 17677 definiert Begriffe für das Widerstandspunkt , Buckel  und Rollennahtschweißen.
ANMERKUNG   Zusätzlich zu den Begriffen in Englisch und Französisch, zwei der drei offiziellen ISO Sprachen, enthält dieser Teile von ISO 17677 die entsprechenden deutschen Begriffe; diese werden unter der Zuständigkeit der Mitgliedsorganisation für Deutschland (DIN) veröffentlicht. Es können jedoch nur die Begriffe in den offiziellen Sprachen als ISO Begriffe und ISO Definitionen angesehen werden.

Soudage par résistance - Vocabulaire - Partie 1: Soudage par points, par bossages et à la molette (ISO 17677-1:2019)

Le présent document établit un vocabulaire de termes et définitions relatifs au soudage par résistance par points, par bossages et à la molette.
NOTE En plus des termes utilisés en anglais et en français, deux des trois langues officielles de l'ISO, le présent document donne les termes équivalents en allemand; ceux-là sont publiés sous la responsabilité du comité membre allemand (DIN). Cependant, seuls les termes et définitions donnés dans les langues officielles peuvent être considérés comme termes et définitions de l'ISO.

Uporovno varjenje - Slovar - 1. del: Točkovno, bradavično in kolutno varjenje (ISO 17677-1:2019)

Ta dokument določa slovar izrazov in definicij za uporovno točkovno, bradavično in kolutno varjenje.
OPOMBA: Poleg tega, da so izrazi v tem dokumentu podani v angleškem in francoskem jeziku (ki sta dva od treh uradnih jezikov ISO), so podani tudi v nemškem jeziku. V slednjem so objavljeni z odgovornostjo ustreznih organov za Nemčijo (DIN). Vendar je kot izraze in definicije ISO mogoče šteti samo tiste, ki so podani v uradnih jezikih.

General Information

Status
Withdrawn
Public Enquiry End Date
29-Jun-2017
Publication Date
04-Sep-2019
Withdrawal Date
15-Apr-2021
Technical Committee
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
12-Apr-2021
Due Date
05-May-2021
Completion Date
16-Apr-2021

Relations

Buy Standard

Standard
EN ISO 17677-1:2019
English, French and German language
55 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 17677-1:2019
01-oktober-2019
Nadomešča:
SIST EN ISO 17677-1:2010
Uporovno varjenje - Slovar - 1. del: Točkovno, bradavično in kolutno varjenje (ISO
17677-1:2019)
Resistance welding - Vocabulary - Part 1: Spot, projection and seam welding (ISO 17677
-1:2019)
Widerstandsschweißen - Begriffe - Teil 1: Punkt-, Buckel- und Rollennahtschweißen (ISO
17677-1:2019)
Soudage par résistance - Vocabulaire - Partie 1: Soudage par points, par bossages et à
la molette (ISO 17677-1:2019)
Ta slovenski standard je istoveten z: EN ISO 17677-1:2019
ICS:
01.040.25 Izdelavna tehnika (Slovarji) Manufacturing engineering
(Vocabularies)
25.160.10 Varilni postopki in varjenje Welding processes
SIST EN ISO 17677-1:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN ISO 17677-1:2019

---------------------- Page: 2 ----------------------
SIST EN ISO 17677-1:2019


EN ISO 17677-1
EUROPEAN STANDARD

NORME EUROPÉENNE

March 2019
EUROPÄISCHE NORM
ICS 25.160.10; 01.040.25 Supersedes EN ISO 17677-1:2009
English Version

Resistance welding - Vocabulary - Part 1: Spot, projection
and seam welding (ISO 17677-1:2019)
Soudage par résistance - Vocabulaire - Partie 1: Widerstandsschweißen - Begriffe - Teil 1: Punkt-,
Soudage par points, par bossages et à la molette (ISO Buckel- und Rollennahtschweißen (ISO 17677-1:2019)
17677-1:2019)
This European Standard was approved by CEN on 30 November 2018.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and United Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2019 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 17677-1:2019 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN ISO 17677-1:2019
EN ISO 17677-1:2019 (E)
Contents Page
European foreword . 3

2

---------------------- Page: 4 ----------------------
SIST EN ISO 17677-1:2019
EN ISO 17677-1:2019 (E)
European foreword
This document (EN ISO 17677-1:2019) has been prepared by Technical Committee ISO/TC 44 "Welding
and allied processes" in collaboration with Technical Committee CEN/TC 121 “Welding and allied
processes” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2019, and conflicting national standards
shall be withdrawn at the latest by September 2019.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 17677-1:2009.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta,
Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
Endorsement notice
The text of ISO 17677-1:2019 has been approved by CEN as EN ISO 17677-1:2019 without any
modification.

3

---------------------- Page: 5 ----------------------
SIST EN ISO 17677-1:2019

---------------------- Page: 6 ----------------------
SIST EN ISO 17677-1:2019
INTERNATIONAL ISO
STANDARD 17677-1
NORME
Second edition
Deuxième édition
INTERNATIONALE
2019-02
Resistance welding — Vocabulary —
Part 1:
Spot, projection and seam welding
Soudage par résistance —
Vocabulaire —
Partie 1:
Soudage par points, par bossages et à
la molette
Widerstandsschweißen — Begriffe —
Teil 1:
Punkt-, Buckel- und
Rollennahtschweißen
Reference number
Numéro de référence
ISO 17677-1:2019(E/F)
©
ISO 2019

---------------------- Page: 7 ----------------------
SIST EN ISO 17677-1:2019
ISO 17677-1:2019(E/F)

COPYRIGHT PROTECTED DOCUMENT
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en oeuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland/Publié en Suisse
ii © ISO 2019 – All rights reserved/Tous droits réservés

---------------------- Page: 8 ----------------------
SIST EN ISO 17677-1:2019
ISO 17677-1:2019(E/F)

Contents Page
Foreword .vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
3.1 Welding and testing procedures . 2
3.2 Hardware and tools . 6
3.3 Welding process and parameters. 8
3.4 Measurements and values .17
Bibliography .44
© ISO 2019 – All rights reserved/Tous droits réservés iii

---------------------- Page: 9 ----------------------
SIST EN ISO 17677-1:2019
ISO 17677-1:2019(E/F)

Sommaire Page
Avant-propos .vii
1 Domaine d‘application . 1
2 Normative references . 1
3 Termes et définitions . 2
3.1 Modes opératoires d’essai et de soudage . 2
3.2 Accessoires et outils . 6
3.3 Procédés et paramètres de soudage . 8
3.4 Mesures et valeurs .17
Bibliographie .44
iv © ISO 2019 – All rights reserved/Tous droits réservés

---------------------- Page: 10 ----------------------
SIST EN ISO 17677-1:2019
ISO 17677-1:2019(E/F)

Inhalt Seite
Vorwort .viii
1 Anwendungsbereich . 1
2 Normative Verweisungen . 1
3 Begriffe . 2
3.1 Schweiß- und Prüfverfahren . 2
3.2 Geräte und Werkzeuge . 6
3.3 Schweißverfahren und Parameter . 8
3.4 Maße und Werte.17
Literaturhinweise .44
© ISO 2019 – All rights reserved/Tous droits réservés v

---------------------- Page: 11 ----------------------
SIST EN ISO 17677-1:2019
ISO 17677-1:2019(E/F)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following URL: www
.iso .org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 44, Welding and allied processes,
Subcommittee SC 6, Resistance welding and allied mechanical joining.
Any feedback, question or request for official interpretation related to any aspect of this document
should be directed to the Secretariat of ISO/TC 44/SC 6 via your national standards body. A complete
listing of these bodies can be found at www .iso .org/members .html. Official interpretations, where they
exist, are available from this page: https: //committee .iso .org/sites/tc44/home/interpretation .html.
This second edition cancels and replaces the first edition (ISO 17677-1:2009), which has been technically
revised. The main changes compared to the previous edition are as follows:
— the terms and definitions of ISO 14329 have been implemented;
—  editorial changes have been made;

vi                                                              © ISO 2019 – All rights reserved/Tous droits réservés

---------------------- Page: 12 ----------------------
SIST EN ISO 17677-1:2019
ISO 17677-1:2019(E/F)

Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes
nationaux de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est
en général confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude
a le droit de faire partie du comité technique créé à cet effet. Les organisations internationales,
gouvernementales et non gouvernementales, en liaison avec l'ISO participent également aux travaux.
L'ISO collabore étroitement avec la Commission électrotechnique internationale (IEC) en ce qui
concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier, de prendre note des différents
critères d'approbation requis pour les différents types de documents ISO. Le présent document a été
rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir www
.iso .org/directives).
L'attention est attirée sur le fait que certains des éléments du présent document peuvent faire l'objet de
droits de propriété intellectuelle ou de droits analogues. L'ISO ne saurait être tenue pour responsable
de ne pas avoir identifié de tels droits de propriété et averti de leur existence. Les détails concernant
les références aux droits de propriété intellectuelle ou autres droits analogues identifiés lors de
l'élaboration du document sont indiqués dans l'Introduction et/ou dans la liste des déclarations de
brevets reçues par l'ISO (voir www .iso .org/brevets).
Les appellations commerciales éventuellement mentionnées dans le présent document sont données
pour information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un
engagement.
Pour une explication de la nature volontaire des normes, la signification des termes et expressions
spécifiques de l'ISO liés à l'évaluation de la conformité, ou pour toute information au sujet de l'adhésion
de l'ISO aux principes de l’Organisation mondiale du commerce (OMC) concernant les obstacles
techniques au commerce (OTC), voir www .iso .org/avant -propos.
Le présent document a été élaboré par le comité technique ISO/TC 44, Soudage et techniques connexes,
Sous-comité SC 6, Soudage par résistance et assemblage mécanique allié.
Il convient que l’utilisateur adresse tout retour d’information ou toute question concernant le présent
document au Secrétariat de l’ISO/TC 44/SC 6 par le biais de l’organisme national de normalisation de
son pays. Une liste exhaustive desdits organismes se trouve à l’adresse www .iso .org/fr/members .html.
Les interprétations officielles, lorsqu'elles existent sont disponibles depuis la page: https: //committee
.iso .org/sites/tc44/home/interpretation .html.
Cette seconde édition annule et remplace la première édition (ISO 17677-1:2009), qui a fait l’objet d’une
révision technique. Les principaux changements par rapport à l’édition précédente sont les suivants:
— les termes et définitions de l’ISO 14329 ont été mis en œuvre;
— des changements éditoriaux ont été effectués.

© ISO 2019 – All rights reserved/Tous droits réservés                                                                           vii

---------------------- Page: 13 ----------------------
SIST EN ISO 17677-1:2019
ISO 17677-1:2019(E/F)

Vorwort
ISO (die Internationale Organisation für Normung) ist eine weltweite Vereinigung nationaler
Normungsorganisationen (ISO-Mitgliedsorganisationen). Die Erstellung von Internationalen Normen
wird üblicherweise von Technischen Komitees von ISO durchgeführt. Jede Mitgliedsorganisation, die
Interesse an einem Thema hat, für welches ein Technisches Komitee gegründet wurde, hat das Recht,
in diesem Komitee vertreten zu sein. Internationale staatliche und nichtstaatliche Organisationen,
die in engem Kontakt mit ISO stehen, nehmen ebenfalls an der Arbeit teil. ISO arbeitet bei allen
elektrotechnischen Themen eng mit der Internationalen Elektrotechnischen Kommission (IEC)
zusammen.
Die Verfahren, die bei der Entwicklung dieses Dokuments angewendet wurden und die für die weitere
Pflege vorgesehen sind, werden in den ISO/IEC-Direktiven, Teil 1 beschrieben. Es sollten insbesondere
die unterschiedlichen Annahmekriterien für die verschiedenen ISO-Dokumentenarten beachtet werden.
Dieses Dokument wurde in Übereinstimmung mit den Gestaltungsregeln der ISO/IEC-Direktiven, Teil 2
erarbeitet (Siehe www .iso .org/directives).
Es wird auf die Möglichkeit hingewiesen, dass einige Elemente dieses Dokuments Patentrechte
berühren können. ISO ist nicht dafür verantwortlich, einige oder alle diesbezüglichen Patentrechte zu
identifizieren. Details zu allen während der Entwicklung des Dokuments identifizierten Patentrechten
finden sich in der Einleitung und/oder in der ISO-Liste der erhaltenen Patenterklärungen (Siehe www
.iso .org/patents).
Jeder in diesem Dokument verwendete Handelsname dient nur zur Unterrichtung der Anwender und
bedeutet keine Anerkennung.
Eine Erläuterung zum freiwilligen Charakter von Normen, der Bedeutung ISO-spezifischer Begriffe
und Ausdrücke in Bezug auf Konformitätsbewertungen sowie Informationen darüber, wie ISO die
Grundsätze der Welthandelsorganisation (WTO) hinsichtlich technischer Handelshemmnisse (TBT)
berücksichtigt, enthält der folgende Link: www .iso .org/iso/foreword .html.
Dieses Dokument wurde vom Technischen Komitee ISO/TC 44, Welding and allied processes,
Unterkomitee SC 6, Resistance welding and allied mechanical joining erarbeitet.
Feedback, Fragen oder Anfragen zu offiziellen Auslegungen der Inhalte dieses Dokuments sollten über
das jeweilige nationale Normungsinstitut an das Sekretariat des ISO/TC 44/SC 6 gerichtet werden.
Eine vollständige Auflistung dieser Institute ist unter www .iso .org/members .html zu finden. Offizielle
Auslegungen, falls sie existieren, sind unter https: //committee .iso .org/sites/tc44/home/interpretation
.html verfügbar.
Diese zweite Ausgabe ersetzt die erste Ausgabe (ISO 17677-1:2009), die technisch überarbeitet wurde.
Die wesentlichen Änderungen im Vergleich zur Vorgängerausgabe sind folgende:
— die Begriffe aus ISO 14329 wurden überführt;
— redaktionelle Anpassungen wurde vorgenommen.

viii                                                            © ISO 2019 – All rights reserved/Tous droits réservés

---------------------- Page: 14 ----------------------
SIST EN ISO 17677-1:2019
INTERNATIONAL STANDARD
NORME INTERNATIONALE ISO 17677-1:2019(E/F)
Resistance Soudage par Widerstands-
welding — résistance — schweißen —
Vocabulary — Vocabulaire — Begriffe —
Part 1: Partie 1: Teil 1:
Spot, projection Soudage par Punkt-, Buckel-
and seam welding points, par und Rollennaht-
bossages et à la schweißen
molette
1 Scope 1 Domaine 1 Anwendungsbereich
d'application
This document establishes Le présent document établit Dieser Dokument
a vocabulary of terms and un vocabulaire de termes et definiert Begriffe für das
definitions for resistance spot définitions relatifs au soudage Widerstandspunkt-, Buckel- und
welding, projection welding and par résistance par points, par Rollennahtschweißen.
seam welding. bossages et à la molette.
ANMERKUNG Zusätzlich
zu den Begriffen in Englisch
NOTE In addition to terms NOTE En plus des termes
und Französisch, zwei der
used in English and French, two utilisés en anglais et en français,
drei offiziellen ISO-Sprachen,
of the three official ISO languages, deux des trois langues officielles
enthält dieser Dokument die
this document gives the equivalent de l'ISO, le présent document
entsprechenden deutschen
terms in German; these are donne les termes équivalents
Begriffe; diese werden
published under the responsibility en allemand; ceux-là sont
unter der Zuständigkeit der
of the member body for Germany publiés sous la responsabilité du
Mitgliedsorganisation für
(DIN). However, only the terms comité membre allemand (DIN).
Deutschland (DIN) veröffentlicht.
and definitions given in the official Cependant, seuls les termes et
Es können jedoch nur die Begriffe
languages can be considered as ISO définitions donnés dans les langues
in den offiziellen Sprachen als
terms and definitions. officielles peuvent être considérés
ISO-Begriffe und ISO-Definitionen
comme termes et définitions de
angesehen werden.
l'ISO.
2 Normative references 2 Références 2 Normative
normatives Verweisungen
There are no normative Le présent document ne contient Es gibt keine normativen
references in this document. aucune référence normative. Verweisungen in diesem
Dokument.
© ISO 2019 – All rights reserved/Tous droits réservés 1

---------------------- Page: 15 ----------------------
SIST EN ISO 17677-1:2019
ISO 17677-1:2019(E/F)

3 Terms and definitions 3 Termes et définitions 3 Begriffe
ISO and IEC maintain L’ISO et l’IEC tiennent à ISO und IEC stellen
terminological databases for jour des bases de données terminologische Datenbanken
use in standardization at the terminologiques destinées à für die Verwendung in der
following addresses: être utilisées en normalisation, Normung unter den folgenden
consultables aux adresses Adressen bereit:
— ISO Online browsing
suivantes:
platform: available at https: — ISO Online-Suchplattform:
//www .iso .org/obp — ISO Online browsing https: //www .iso .org/obp
platform: disponible à
— IEC Electropedia: — IEC Electropedia: http:
l’adresse https: //www .iso
available at http: //www //www .electropedia .org/
.org/obp
.electropedia .org/
— IEC Electropedia: disponible
à l’adresse http: //www
.electropedia .org/
3.1 Welding and testing 3.1 Modes opératoires 3.1 Schweiß- und
procedures d’essai et de soudage Prüfverfahren
3.1.1 3.1.1 3.1.1
chisel test essai au burin Meißelprüfung
test in which a chisel is driven essai dans lequel un burin est Keilprüfung
between the sheets near to adja- enfoncé entre les tôles et à Prüfung, bei der ein Meißel nahe
cent welds until either fracture proximité des soudures jusqu'à der Schweißverbindung zwi-
occurs or until the metal near ce que survienne une rupture schen die Bleche getrieben wird,
the weld yields or bends dans la soudure, ou jusqu'à ce entweder bis zum Bruch oder
que le métal atteigne sa limite bis sich das Blech im Bereich der
d'élasticité ou plie Verbindung verformt
3.1.2 3.1.2 3.1.2
cross tension test essai de traction sur éprou- Kopfzugprüfung
tensile test of a resistance vette en croix Zugprüfung einer widerstands-
welded specimen to determine essai de traction sur une éprou- geschweißten Verbindung zur
the mechanical properties and vette soudée par résistance Ermittlung der von der Probe
failure mode of the weld pour déterminer les propriétés ertragbaren Zugkraft
mécaniques et le mode de rup-
ture de la soudure
3.1.3 3.1.3 3.1.3
cross-wire welding soudage de fils en croix Kreuzdrahtschweißung
projection welding (3.1.11) of soudage par bossages (3.1.11) de Buckelschweißen (3.1.11) von
crossed wires or rods fils ou de baguettes en croix gekreuzten Drähten oder Stäben
2 © ISO 2019 – All rights reserved/Tous droits réservés

---------------------- Page: 16 ----------------------
SIST EN ISO 17677-1:2019
ISO 17677-1:2019(E/F)

3.1.4 3.1.4 3.1.4
direct welding soudage direct direktes Schweißen
resistance welding secondary variante en circuit secondaire Variante des Sekundärkreises
circuit variant in which wel- du soudage par résistance dans beim Widerstandsschweißen,
ding current and electrode laquelle le courant de soudage et bei der der Schweißstrom und
force (3.3.5) are applied to the l'effort sur électrodes (3.3.5) sont die Elektrodenkraft (3.3.5)
workpieces by directly opposed appliqués aux pièces à souder durch einander direkt gegen-
electrodes (3.2.1) and only one par des électrodes (3.2.1) direc- überstehende Elektroden (3.2.1)
weld is made by one welding tement opposées et où une seule eingeleitet werden und bei der
operation soudure est réalisée à chaque in einem Schweißvorgang nur
opération de soudage eine Schweißung hergestellt
Note 1 to entry: See Figure 13 for
wird
typical arrangements.
Note 1 à l'article: Voir Figure 13
pour les dispositions types.
Anmerkung 1 zum Begriff: Siehe
Bild 13 für typische Anordnungen.
3.1.5 3.1.5 3.1.5
indirect welding soudage indirect indirektes Schweißen
resistance welding secondary variante en circuit secondaire Variante des Sekundärkreises
circuit variant in which the wel- du soudage par résistance dans beim Widerstandsschweißen,
ding current flows through the laquelle le courant de soudage bei der der Schweißstrom
workpieces in locations away passe dans les pièces à souder à sowohl an der Stelle der ge-
from, as well as at, the welds l'écart de la soudure aussi bien wünschten Verbindungs-Positi-
que sur la soudure on durch das Werkstück fließt,
Note 1 to entry: See Figure 14 for
als auch abseits davon
typical arrangements.
Note 1 à l'article: Voir Figure 14
pour les dispositions types.
Anmerkung 1 zum Begriff: Siehe
Bild 14 für typische Anordnungen.
3.1.6 3.1.6 3.1.6
multiple impulse welding soudage par impulsions Mehrimpulsschweißung
welding with more than one soudure réalisée avec plus d'une Schweißung mit mehr als einem
impulse impulsion Impuls
Note 1 to entry: See Figures 4 to 8 Note 1 à l'article: Voir Figures 4 à Anmerkung 1 zum Begriff: Siehe
for related time and electrode force 8 relatives au diagramme temps/ Bilder 4 bis 8 für die jeweiligen
(3.3.5) diagrams. effort sur électrodes (3.3.5). Zeit- und Elektrodenkraftdiagram-
me (3.3.5).
3.1.7 3.1.7 3.1.7
multiple spot welding soudage par points multiples Mehrpunktschweißung
spot welding in which two or soudage par point
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.