SIST EN ISO 21904-4:2020
(Main)Health and safety in welding and allied processes - Equipment for capture and separation of welding fume - Part 4: Determination of the minimum air volume flow rate of capture devices (ISO 21904-4:2020)
Health and safety in welding and allied processes - Equipment for capture and separation of welding fume - Part 4: Determination of the minimum air volume flow rate of capture devices (ISO 21904-4:2020)
EN-ISO 21904-4 specifies two methods for establishing the minimum air volume flow rate. One method is dedicated for use with captor hoods, nozzles and slot nozzles with a ratio of slot length to hose diameter of 8:1 or less. The other method is dedicated for use with on-gun extraction devices.These methods are not applicable to down draught tables.
Arbeits- und Gesundheitsschutz beim Schweißen und bei verwandten Verfahren - Einrichtungen zum Erfassen und Abscheiden von Schweißrauch - Teil 4: Bestimmen des Mindestluftvolumenstromes von Absaugeinrichtungen (ISO 21904-4:2020)
Dieses Dokument legt zwei Verfahren zur Festlegung des Mindestluftvolumenstroms fest. Ein Verfahren ist für die Verwendung mit Abzugshauben, Düsen und Schlitzdüsen mit einem Verhältnis der Schlitzlänge zum Schlauchdurchmesser von 8 : 1 oder weniger geeignet. Das andere Verfahren ist für die Verwendung mit brennerintegrierten Absaugeinrichtungen geeignet.
Diese Verfahren sind nicht für abgesaugte Schweißtische geeignet.
Hygiène et sécurité en soudage et techniques connexes - Équipements de captage et de filtration des fumées - Partie 4: Détermination du débit volumique minimal d'air des dispositifs de captage (ISO 21904-4:2020)
Le présent document spécifie deux méthodes qui permettent de déterminer le débit volumique d'air minimal. Une méthode est applicable pour l'utilisation avec des dispositifs de captage, des buses et des fentes aspirantes ayant un rapport longueur de fente sur diamètre du tuyau inférieur ou égal à 8:1. L'autre méthode est applicable pour l'utilisation avec des torches aspirantes de soudage.
Ces méthodes ne s'applique aux tables aspirantes.
Zdravje in varnost pri varjenju in sorodnih postopkih - Oprema za zajem in ločevanje varilnega dima - 4. del: Določanje najmanjšega volumenskega pretoka zraka skozi odsesovalne naprave (ISO 21904-4:2020)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
SIST EN ISO 21904-4:2020
01-maj-2020
Nadomešča:
SIST EN ISO 15012-2:2008
Zdravje in varnost pri varjenju in sorodnih postopkih - Oprema za zajem in
ločevanje varilnega dima - 4. del: Določanje najmanjšega volumenskega pretoka
zraka skozi odsesovalne naprave (ISO 21904-4:2020)
Health and safety in welding and allied processes - Equipment for capture and
separation of welding fume - Part 4: Determination of the minimum air volume flow rate
of capture devices (ISO 21904-4:2020)
Arbeits- und Gesundheitsschutz beim Schweißen und bei verwandten Verfahren -
Einrichtungen zum Erfassen und Abscheiden von Schweißrauch - Teil 4: Bestimmen des
Mindestluftvolumenstromes von Absaugeinrichtungen (ISO 21904-4:2020)
Hygiène et sécurité en soudage et techniques connexes - Équipements de captage et de
filtration des fumées - Partie 4: Détermination du débit volumique minimal d'air des
dispositifs de captage (ISO 21904-4:2020)
Ta slovenski standard je istoveten z: EN ISO 21904-4:2020
ICS:
13.040.40 Emisije nepremičnih virov Stationary source emissions
13.100 Varnost pri delu. Industrijska Occupational safety.
higiena Industrial hygiene
25.160.30 Varilna oprema Welding equipment
SIST EN ISO 21904-4:2020 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 21904-4:2020
---------------------- Page: 2 ----------------------
SIST EN ISO 21904-4:2020
EN ISO 21904-4
EUROPEAN STANDARD
NORME EUROPÉENNE
March 2020
EUROPÄISCHE NORM
ICS 13.100; 25.160.30 Supersedes EN ISO 15012-2:2008
English Version
Health and safety in welding and allied processes -
Equipment for capture and separation of welding fume -
Part 4: Determination of the minimum air volume flow
rate of capture devices (ISO 21904-4:2020)
Hygiène et sécurité en soudage et techniques connexes Arbeits- und Gesundheitsschutz beim Schweißen und
- Équipements de captage et de filtration des fumées - bei verwandten Verfahren - Einrichtungen zum
Partie 4: Détermination du débit volumique minimal Erfassen und Abscheiden von Schweißrauch - Teil 4:
d'air des dispositifs de captage (ISO 21904-4:2020) Bestimmen des Mindestluftvolumenstromes von
Absaugeinrichtungen (ISO 21904-4:2020)
This European Standard was approved by CEN on 20 January 2020.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 21904-4:2020 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 21904-4:2020
EN ISO 21904-4:2020 (E)
Contents Page
European foreword . 3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 21904-4:2020
EN ISO 21904-4:2020 (E)
European foreword
This document (EN ISO 21904-4:2020) has been prepared by Technical Committee ISO/TC 44 "Welding
and allied processes" in collaboration with Technical Committee CEN/TC 121 “Welding and allied
processes” the secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by September 2020, and conflicting national standards
shall be withdrawn at the latest by September 2020.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 15012-2:2008.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 21904-4:2020 has been approved by CEN as EN ISO 21904-4:2020 without any
modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 21904-4:2020
---------------------- Page: 6 ----------------------
SIST EN ISO 21904-4:2020
INTERNATIONAL ISO
STANDARD 21904-4
First edition
2020-02
Health and safety in welding and allied
processes — Equipment for capture
and separation of welding fume —
Part 4:
Determination of the minimum air
volume flow rate of capture devices
Hygiène et sécurité en soudage et techniques connexes —
Équipements de captage et de filtration des fumées —
Partie 4: Détermination du débit volumique minimal d'air des
dispositifs de captage
Reference number
ISO 21904-4:2020(E)
©
ISO 2020
---------------------- Page: 7 ----------------------
SIST EN ISO 21904-4:2020
ISO 21904-4:2020(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2020
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2020 – All rights reserved
---------------------- Page: 8 ----------------------
SIST EN ISO 21904-4:2020
ISO 21904-4:2020(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Captor hoods, nozzles and slot nozzles . 1
4.1 Principle . 1
4.2 Apparatus . 2
4.3 Test method . 2
4.3.1 Test setup . 2
4.3.2 Determination of the position of the entry and the measurement plane . 2
4.3.3 Procedure . 3
4.4 Test report . 4
5 On-torch extraction devices . 5
5.1 Principle . 5
5.2 Apparatus . 6
5.3 Test method . 6
5.3.1 Test setup . 6
5.3.2 Procedure . 6
5.4 Test report . 7
Annex A (informative) Additional information for on-torch extraction. 8
Bibliography .10
© ISO 2020 – All rights reserved iii
---------------------- Page: 9 ----------------------
SIST EN ISO 21904-4:2020
ISO 21904-4:2020(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see www .iso .org/
iso/ foreword .html.
This document was prepared by Technical Committee ISO/TC 44, Welding and allied processes,
Subcommittee SC 9, Health and safety.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www .iso .org/ members .html.
Official interpretations of ISO/TC 44 documents, where they exist, are available from this page: https://
committee .iso .org/ sites/ tc44/ home/ interpretation .html.
A list of all parts in the ISO 21904 series can be found on the ISO website.
This first edition cancels and replaces ISO 15012-2.
iv © ISO 2020 – All rights reserved
---------------------- Page: 10 ----------------------
SIST EN ISO 21904-4:2020
ISO 21904-4:2020(E)
Introduction
Welding and allied processes generate fume and gases, which, if inhaled, can be harmful to human
health. Control is often required to maintain exposure at acceptable levels and this can be achieved by
capturing the fume and gases using local exhaust ventilation.
For a particular capture device, the air velocity
...
SLOVENSKI STANDARD
oSIST prEN ISO 21904-4:2019
01-marec-2019
=GUDYMHLQYDUQRVWSULYDUMHQMXLQVRURGQLKWHKQLNDK2SUHPD]D]DMHPLQ
ORþHYDQMHYDULOQHJDGLPDGHO 'RORþDQMHQDMPDQMãHJDYROXPHQVNHJDSUHWRND
]UDNDVNR]LRGVHVRYDOQHQDSUDYH ,62',6
Health and safety in welding and allied processes - Equipment for capture and
separation of welding fume - Part 4: Determination of the minimum air volume flow rate
of capture devices (ISO/DIS 21904-4:2019)
Arbeits- und Gesundheitsschutz beim Schweißen und bei verwandten Verfahren -
Einrichtungen zum Erfassen und Abscheiden von Schweißrauch - Teil 4: Bestimmen des
Mindestluftvolumenstromes von Absaugeinrichtungen (ISO/DIS 21904-4:2019)
Hygiène et sécurité en soudage et techniques connexes - Équipements de captage et de
filtration des fumées - Partie 4: Détermination du débit volumique minimal d'air des
dispositifs de captage (ISO/DIS 21904-4:2019)
Ta slovenski standard je istoveten z: prEN ISO 21904-4
ICS:
13.040.40 (PLVLMHQHSUHPLþQLKYLURY Stationary source emissions
13.100 Varnost pri delu. Industrijska Occupational safety.
higiena Industrial hygiene
25.160.30 Varilna oprema Welding equipment
oSIST prEN ISO 21904-4:2019 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN ISO 21904-4:2019
---------------------- Page: 2 ----------------------
oSIST prEN ISO 21904-4:2019
DRAFT INTERNATIONAL STANDARD
ISO/DIS 21904-4
ISO/TC 44/SC 9 Secretariat: BSI
Voting begins on: Voting terminates on:
2019-01-21 2019-04-15
Health and safety in welding and allied processes —
Equipment for capture and separation of welding fume —
Part 4:
Determination of the minimum air volume flow rate of
capture devices
ICS: 13.100; 25.160.30
THIS DOCUMENT IS A DRAFT CIRCULATED
This document is circulated as received from the committee secretariat.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
IN ADDITION TO THEIR EVALUATION AS
ISO/CEN PARALLEL PROCESSING
BEING ACCEPTABLE FOR INDUSTRIAL,
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO/DIS 21904-4:2019(E)
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2019
---------------------- Page: 3 ----------------------
oSIST prEN ISO 21904-4:2019
ISO/DIS 21904-4:2019(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved
---------------------- Page: 4 ----------------------
oSIST prEN ISO 21904-4:2019
ISO/DIS 21904-4:2019(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Captor hoods, nozzles and slot nozzles . 1
4.1 Principle . 1
4.2 Equipment . 1
4.3 Test method . 2
4.3.1 Test setup . 2
4.3.2 Determination of the position of the entry and the measurement plane . 2
4.3.3 Procedure . 3
4.4 Test report . 3
5 On-gun extraction devices . 4
5.1 Principle . 4
5.2 Equipment . 5
5.3 Test method . 5
5.3.1 Test setup . 5
5.3.2 Procedure . 6
5.4 Test report . 7
Annex A (informative) Equipment note . 8
Annex B (informative) Additional information for on-torch extraction. 9
Bibliography .11
© ISO 2019 – All rights reserved iii
---------------------- Page: 5 ----------------------
oSIST prEN ISO 21904-4:2019
ISO/DIS 21904-4:2019(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: www .iso .org/iso/foreword .html.
This document was prepared by Technical Committee ISO/TC 44, Welding and allied processes,
Subcommittee SC 9, Health and safety.
A list of all parts in the ISO 21904-series can be found on the ISO website.
Requests for official interpretations of any aspect of this document should be directed to the Secretariat
of ISO/TC 44/SC 9 via your national standards body. A complete listing of these bodies can be found at
www .iso .org.
iv © ISO 2019 – All rights reserved
---------------------- Page: 6 ----------------------
oSIST prEN ISO 21904-4:2019
ISO/DIS 21904-4:2019(E)
Introduction
Welding and allied processes generate fume and gases, which, if inhaled, can be harmful to human
health. Control is often required to maintain exposure at acceptable levels and this can be achieved by
capturing the fume and gases using local exhaust ventilation.
For a particular capture device, the air velocity to capture welding fume can only be achieved by
applying a minimum air volume flow rate. Consequently, capture devices need to be used with exhaust
systems that provide, at least, the minimum air volume flow rate.
© ISO 2019 – All rights reserved v
---------------------- Page: 7 ----------------------
oSIST prEN ISO 21904-4:2019
---------------------- Page: 8 ----------------------
oSIST prEN ISO 21904-4:2019
DRAFT INTERNATIONAL STANDARD ISO/DIS 21904-4:2019(E)
Health and safety in welding and allied processes —
Equipment for capture and separation of welding fume —
Part 4:
Determination of the minimum air volume flow rate of
capture devices
1 Scope
This part of ISO 21904 specifies two methods for establishing the minimum air volume flow rate. One
method is dedicated for use with captor hoods, nozzles and slot nozzles with a ratio of slot length to
hose diameter of 8:1 or less. The other method is dedicated for use with on-gun extraction devices.
Neither method is applicable to down draught tables.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.
ISO 12100, Safety of machinery — General principles for design — Risk assessment and risk reduction
3 Terms and definitions
For the purposes of this docume
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.