Roofing products from metal sheet - Specification for self-supporting products of steel, aluminium or stainless steel sheet - Part 1: Steel

This Part of EN 508 specifies requirements for self-supporting roofing products for discontinuous laying made from metallic coated steel sheet with or without additional organic coatings.
The standard establishes general characteristics, definitions, classifications and labelling for the products, together with requirements for the materials from which the products can be manufactured. It is intended to be used either by manufacturers to ensure that their products comply with the requirements or by purchasers to verify that the products comply when purchased before they are despatched from the factory. It specifies the requirements for products which enable them to meet all normal service conditions.
The standard applies to all discontinuously laid self-supporting external profiled sheets for roofing with the exception of tiles with a surface area less than 1 m2 and produced by stamping. These profiled roof sheets are designed to keep wind, rain and snow out of the building and to transfer any resultant loads and infrequent maintenance loads to the structure.
No requirements for supporting construction, design of roof system and execution of connections and flashings are included.

Dachdeckungsprodukte aus Metallblech - Festlegungen für selbsttragende Bedachungselemente aus Stahlblech, Aluminiumblech oder nichtrostendem Stahlblech - Teil 1: Stahl

Dieser Teil von EN 508 legt Anforderungen an selbsttragende Dacheindeckungsprodukte zur überlappenden Verlegung fest, die aus Stahlblech mit metallischem Überzug, mit oder ohne zusätzliche organische Beschichtung, gefertigt wurden.
Die Norm legt die allgemeinen Merkmale, Definitionen, Klassifizierungen und die Beschriftung für die Produkte fest, sowie die Anforderungen an die Werkstoffe, aus denen die Produkte hergestellt werden können. Sie ist dafür bestimmt, entweder vom Hersteller verwendet zu werden, um sicherzustellen, dass seine Produkte den Anforderungen entsprechen, oder vom Käufer, um zu überprüfen, ob die Produkte den Anforderungen entsprechen, bevor sie das Werk verlassen. Die Norm legt die Anforderungen an Produkte fest, unter denen die Produkte allen normalen Einsatzbedingungen gerecht werden können.
Die Norm gilt für alle außen verwendeten, überlappend verlegten, selbsttragenden Profilbleche, sie gilt nicht für Dachpfannen mit einer Oberfläche < 1 m2 und gepresste Dachpfannen. Diese Profilbleche zur Dacheindeckung sind so ausgelegt, dass sie das Eindringen von Wind, Regen und Schnee in das Gebäude verhindern und dass alle daraus und alle aus nicht ständig durchgeführten Instandhaltungsarbeiten resultierenden Lasten auf das Bauwerk übertragen werden.
Anforderungen an die Unterkonstruktion, die Konstruktion des Dachsystems und an die Ausführung der Verbindungen und an Kehlbleche sind nicht Gegenstand dieser Norm.

Produits de couverture en tôle métallique - Spécification pour les plaques de couverture en tôle d'acier, d'aluminium ou d'acier inoxydable - Partie 1 : Acier

Cette partie de l'EN 508 spécifie les prescriptions relatives aux plaques de couverture pour pose en discontinu en tôles d'acier revêtues avec ou sans revêtement organique supplémentaire.
La norme donne les caractéristiques générales, les définitions, les classifications et l'étiquetage applicables aux produits, de même que les prescriptions relatives aux matériaux à partir desquels les produits peuvent être fabriqués. Elle est destinée à être utilisée soit par des fabricants en vue de démontrer que leurs produits sont conformes aux prescriptions, soit par des acheteurs pour vérifier que les produits sont conformes avant leur expédition de l’usine. Elle spécifie les prescriptions relatives aux produits pour leur permettre de répondre à toutes les conditions normales en service.
La norme s'applique à toutes les plaques profilées extérieures de couverture posées en discontinu à l’exception des tuiles de surface inférieure à 1 m² et produites par estampage. Ces plaques profilées sont conçues pour empêcher le vent, la pluie et la neige de pénétrer dans le bâtiment et pour transmettre à la structure porteuse les charges qui en résultent ainsi que les charges non permanentes dues aux opérations d'entretien.
Aucune prescription relative à la structure porteuse, à la conception du système de toiture et à la réalisation des assemblages et des finitions n'est incluse

Pločevina za pokrivanje streh - Specifikacije za samonosilne proizvode iz jeklene, aluminijeve pločevine ali pločevine iz nerjavnega jekla - 1. del: Jeklo

General Information

Status
Withdrawn
Public Enquiry End Date
30-Mar-2008
Publication Date
05-Oct-2008
Withdrawal Date
02-Sep-2014
Technical Committee
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
03-Sep-2014
Due Date
26-Sep-2014
Completion Date
03-Sep-2014

Relations

Buy Standard

Standard
EN 508-1:2008
English language
46 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Dachdeckungsprodukte aus Metallblech - Festlegungen für selbsttragende Bedachungselemente aus Stahlblech, Aluminiumblech oder nichtrostendem Stahlblech - Teil 1: StahlProduits de couverture en tôle métallique - Spécification pour les plaques de couverture en tôle d'acier, d'aluminium ou d'acier inoxydable - Partie 1 : AcierRoofing products from metal sheet - Specification for self-supporting products of steel, aluminium or stainless steel sheet - Part 1: Steel91.060.20StreheRoofs77.140.50SROL]GHONLFlat steel products and semi-productsICS:Ta slovenski standard je istoveten z:EN 508-1:2008SIST EN 508-1:2008en,fr,de01-november-2008SIST EN 508-1:2008SLOVENSKI
STANDARDSIST EN 508-1:20021DGRPHãþD



SIST EN 508-1:2008



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 508-1July 2008ICS 91.060.20Supersedes EN 508-1:2000
English VersionRoofing products from metal sheet - Specification for self-supporting products of steel, aluminium or stainless steel sheet -Part 1: SteelProduits de couverture en tôle métallique - Spécificationpour les plaques de couverture en tôles d'acier,d'aluminium ou d'acier inoxydable - Partie 1 : AcierDachdeckungsprodukte aus Metallblech - Festlegungen fürselbsttragende Bedachungselemente aus Stahlblech,Aluminiumblech oder nichtrostendem Stahlblech - Teil 1:StahlThis European Standard was approved by CEN on 30 May 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2008 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 508-1:2008: ESIST EN 508-1:2008



EN 508-1:2008 (E) 2 Contents Page Foreword.4 Introduction.5 1 Scope.6 2 Normative references.6 3 Terms and definitions, symbols and abbreviations.6 3.1 General.7 3.2 Materials.7 3.3 Profile definitions.8 3.4 Product geometry.10 3.5 Symbols and abbreviations.13 4 Requirements.14 4.1 General.14 4.2 Materials.15 4.2.1 Materials for roll formed and brake pressed profiles.15 4.2.2 Materials for tiles.15 4.2.3 Nominal metallic coating.15 4.2.4 Organic coatings.16 4.3 Products.17 4.3.1 Mechanical resistance.17 4.3.2 Calculation and test of mechanical resistance.17 4.3.3 Dimensions.17 4.3.4 Dimensional tolerances for the profiled sheets.17 4.3.5 Safety in case of fire.17 5 Test methods.18 5.1 Material properties.18 5.2 Structural properties.18 6 Designation.18 7 Marking, labelling and packaging.18 7.1 Marking and labelling.18 7.2 Packaging and special ordering conditions.19 7.3 Transport, storage and handling.19 Annex A (informative)
Aluminium coated steel sheet (type A).20 A.1 General.20 A.2 Specification for roof covering products.20 A.2.1 Steel grades.20 A.2.2 Coating mass.20 A.2.3 Dimensional tolerances.21 Annex B (normative)
Multilayer coated steel sheet.22 B.1 General.22 B.2 Substrate material.22 B.3 Specific requirements.22 B.3.1 Minimum nominal values of thickness.22 B.3.2 Bituminous coating specification.22 B.3.3 Durability.23 B.4 Freedom from defects.23 Annex C (informative)
Metallic coatings.24 SIST EN 508-1:2008



EN 508-1:2008 (E) 3 Annex D (normative)
Dimensional tolerances.27 D.1 Tolerances for trapezoidal sheets.27 D.1.1 General.27 D.1.2 Depth of profile.27 D.1.3 Depth of stiffeners.28 D.1.4 Pitch.28 D.1.5 Widths of crown and valley.29 D.1.6 Cover width.29 D.1.7 Radius of bends.30 D.1.8 Deviation from straightness.31 D.1.9 Deviation from squareness.31 D.1.10 Length.32 D.1.11 Deviation of side lap.33 D.1.12 Curve radius and angles.33 D.2 Tolerances for sinusoidal profiles.34 D.3 Tolerances on tiles.34 D.3.1 General.34 D.3.2 Depth of tile.35 D.3.3 Web angular displacement (Figure D.12).36 D.3.4 Pitch.36 D.3.5 Width of crown and valley (Figure D.14).36 D.3.6 Cover width.37 D.3.7 Radius of bends.37 D.3.8 Deviation from straightness.38 D.3.9 Deviation from squareness.39 D.3.10 Length.39 D.3.11 Contraction or bulging.39 D.4 Methods for measuring profiles.40 D.4.1 General.40 D.4.2 Depth of profile.40 D.4.3 Depth of stiffeners.41 D.4.4 Pitch.41 D.4.5 Width of crown and valley.42 D.4.6 Cover width.42 D.4.7 Radius of bends.42 D.4.8 Straightness.42 D.4.9 Squareness.42 D.4.10 Length.43 D.4.11 Side laps.43 D.4.12 Side lap ripple.43 Annex E (informative)
Test methods for concentrated load.45 Bibliography.46
SIST EN 508-1:2008



EN 508-1:2008 (E) 4 Foreword This document (EN 508-1:2008) has been prepared by Technical Committee CEN/TC 128 “Roof covering products for discontinuous laying and products for wall cladding”, the secretariat of which is held by NBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2009, and conflicting national standards shall be withdrawn at the latest by January 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 508-1:2000. EN 508 Roofing products from metal sheet - Specification for self-supporting products of steel, aluminium or stainless steel sheet consists of the following parts:  Part 1: Steel;  Part 2: Aluminium;  Part 3: Stainless steel. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. SIST EN 508-1:2008



EN 508-1:2008 (E) 5 Introduction Figure 1 indicates the position of this standard in the CEN framework of standards concerning roofing products of metal.
Roofing products of metal
Self-supporting products
Fully supported products
EN 14782
Copper / Zinc
EN 506
Steel
EN 508-1
Aluminium EN 508-2
Stainless steel
EN 508-3
Figure 1 — Framework of standards In this standard the performance of the product has been defined in terms of calculation and a number of type tests.
The performance of a roof constructed with these products depends not only on the properties of the product as required by this standard, but also on the design, construction and performance of the roof as a whole in relation to the environment and conditions of use. SIST EN 508-1:2008



EN 508-1:2008 (E) 6 1 Scope This Part of EN 508 specifies requirements for self-supporting roofing products for discontinuous laying made from metallic coated steel sheet with or without additional organic coatings.
The standard establishes general characteristics, definitions, classifications and labelling for the products, together with requirements for the materials from which the products can be manufactured. It is intended to be used either by manufacturers to ensure that their products comply with the requirements or by purchasers to verify that the products comply when purchased before they are despatched from the factory. It specifies the requirements for products which enable them to meet all normal service conditions. The standard applies to all discontinuously laid self-supporting external profiled sheets for roofing with the exception of tiles with a surface area less than 1 m2 and produced by stamping. These profiled roof sheets are designed to keep wind, rain and snow out of the building and to transfer any resultant loads and infrequent maintenance loads to the structure. No requirements for supporting construction, design of roof system and execution of connections and flashings are included.
2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 10143, Continuously hot-dip coated steel sheet and strip - Tolerances on dimensions and shape EN 10169-1:2003, Continuously organic coated (coil coated) steel flat products - Part 1: General information (definitions, materials, tolerances, test methods) EN 10169-2, Continuously organic coated (coil coated) steel flat products - Part 2: Products for building exterior applications EN 10169-3, Continuously organic coated (coil coated) steel flat products - Part 3: Products for building interior applications EN 10326, Continuously hot-dip coated strip and sheet of structural steels - Technical delivery conditions EN 10327, Continuously hot-dip coated strip and sheet of low carbon steels for cold forming - Technical delivery conditions EN ISO 6270-1, Paints and varnishes - Determination of resistance to humidity - Part 1: Continuous condensation (ISO 6270-1:1998) EN ISO 6988, Metallic and other non-organic coatings - Sulfur dioxide test with general condensation of moisture (ISO 6988:1985) EN ISO 9227, Corrosion tests in artificial atmospheres - Salt spray tests (ISO 9227:2006) 3 Terms and definitions, symbols and abbreviations For the purposes of this standard, the terms and definitions given in EN 10169-1 and the following apply. SIST EN 508-1:2008



EN 508-1:2008 (E) 7 3.1 General 3.1.1 Self-supporting product Product which will, by virtue of its material and shape, support all applied loadings (e.g. snow, wind, foot traffic), and transmit these loadings to spaced structural supports 3.2 Materials 3.2.1 hot-dip zinc coated steel sheet (type Z)
product obtained by continuously hot-dip zinc coating cold reduced strips of either low carbon steel for cold forming or steel of structural quality NOTE 1
For steel of structurally quality, see EN 10326; for low carbon steel for cold forming, see EN 10327. NOTE
2 A new standard (prEN10346) that will merge EN 10326 and EN 10327 is currently in preparation. 3.2.2 hot-dip 5 % Al-Zn coated steel sheet (type ZA)
product obtained by continuously hot-dip coating cold reduced strips of low carbon steel for cold forming or steel of structural quality on a production line using an alloy consisting of zinc and approximately 5 % aluminium (nominal percentage by mass) NOTE 1 For steel of structurally quality, see EN 10326; for low carbon steel for cold forming, see EN 10327. NOTE 2 A new standard (prEN10346) that will merge EN 10326 and EN 10327 is currently in preparation. 3.2.3 hot-dip 55 % Al-Zn
coated steel sheet (type AZ)
product obtained by continuously hot-dip coating cold reduced strips of low carbon steel for cold forming or steel of structural quality on a production line using an alloy consisting of :  55 % aluminium (nominal percentage by mass);  1,6 % silicon (nominal percentage by mass);  and the balance zinc NOTE 1 For steel of structurally quality, see EN 10326; for low carbon steel for cold forming, see EN 10327. NOTE 2 A new standard (prEN10346) that will merge EN 10326 and EN 10327 is currently in preparation. 3.2.4 hot-dip aluminium coated steel sheet (type A)
product obtained by continuously hot-dip aluminium coating cold reduced strips of low carbon steel for cold forming steel or steel of structural quality on a production line NOTE See Annex A. 3.2.5 organic coated steel sheet product obtained by factory application of paint by roller or spray processes, or factory application of laminated organic film, on substrates of type Z, type ZA, type AZ or type A coated steel sheet NOTE 1 EN 10169-1 refers to this type of coated steel.
NOTE 2
A new standard (prEN 10169) that will merge EN 10169-1, -2 and -3 is currently in preparation. SIST EN 508-1:2008



EN 508-1:2008 (E) 8 3.2.6 multilayer coated steel sheet product obtained by continuously coating on both sides hot-dip zinc coated cold reduced strips of low carbon steel for cold forming or steel of structural quality with one or multiple applications of thermoplastic asphalt compounds (minimum thickness 1,5 mm) and subsequent lamination of a metal foil with or without decorative painting NOTE See Annex B. 3.3 Profile definitions 3.3.1 trapezoidal profiled sheet self-supporting sheet which is designed to allow it to be side and end lapped, the crowns of which may be rounded and, in addition, the crowns, webs and valleys may be stiffened NOTE
See Figures 2 to 5.
Figure 2 — Part of typical trapezoidal profile
Figure 3 — Part of typical trapezoidal profile with rounded crowns
Figure 4 — Part of typical trapezoidal profile with stiffened crown and web
Figure 5 — Part of typical trapezoidal profile with stiffened valley SIST EN 508-1:2008



EN 508-1:2008 (E) 9 3.3.2 sinusoidal profiled sheet self-supporting sheet which is designed to allow it to be side and end lapped, comprising a series of arc shaped crowns and valleys interconnected with tangential webs NOTE
See Figure 6.
Figure 6 — Part of typical sinusoidal profiled sheet
3.3.3 standing seam and concealed fix sheet self-supporting sheet profiled in such a way that the fixings are hidden within the construction and are not exposed to the weather NOTE 1 The profile shape is designed to allow the formation of side laps on site. NOTE 2 As these types of roof covering products are used in proprietary roofing systems, no structural requirements are given within this Part of EN 508.
NOTE 3 See Figures 7 and 8. NOTE 4 These products are normally designed by testing.
Figure 7 — Typical standing seam profile
Figure 8 — Typical concealed fix profile 3.3.4 tile profiles parts of typical tile profiled sheets that can allow the sheet to be side and/or end lapped SIST EN 508-1:2008



EN 508-1:2008 (E) 10 NOTE 1 The tile profile may include transverse steps. NOTE 2 As these types of roof covering products are used in proprietary systems no structural requirements are given within this Part of EN 508. NOTE 3 See figures 9a, 9b and 9c. NOTE 4 These products are normally designed by testing.
Figure 9 — Typical tile profiles 3.4 Product geometry NOTE The names for various parts of typical trapezoidal profiled sheets are given in Figures 10a and 10b, with additional definitions for sinusoidal profiles in Figure 11 and tile profiles in Figure 12.
SIST EN 508-1:2008



EN 508-1:2008 (E) 11
Key 1 Cover width 7 Depth 2 Valley stiffener 8 Valley 3 Rib 9 Pitch 4 Web stiffener 10 Crown 5 Trough 11 Drainage groove 6 Web 12 Crown stiffener a) Definitions of the parts of typical trapezoidal profiled sheets SIST EN 508-1:2008



EN 508-1:2008 (E) 12
Key 1 Bend radius 2 End lap 3 Web angle 4 Overlap 5 Underlap 6 Side lap in principle the same on tiles b) Definitions of the parts of typical trapezoidal profiled sheets Figure 10: Definitions of the parts of typical profiled sheets SIST EN 508-1:2008



EN 508-1:2008 (E) 13
Key 1 Depth 2 Pitch Figure 10 — Definitions of the parts of typical sinusoidal profiled sheets
Key 1 Height of the step 2 Length of the step 3 Number of steps 4 End lap Figure 11 — Definitions of the parts of typical tile
3.5 Symbols and abbreviations Z Hot-dip zinc coated steel ZA Hot-dip zinc/aluminium coated steel AZ Hot-dip aluminium/zinc coated steel A Hot-dip aluminium coated steel ML Multilayer coated steel AY Acrylic paint coating SP Polyester paint coating SIST EN 508-1:2008



EN 508-1:2008 (E) 14 SP-PI Silicone-modified polyester paint coating HDP High durable polyester PVDF Polyvinylidenefluoride paint coating PVC(P) Polyvinylchloride (plastisol) coating, applied by coil coating process.
PUR Polyurethane paint coating PUR-PA Polyurethane-modified polyester paint coating SP-PA Polyamide-modified polyester paint coating PVC(F) Polyvinylchloride (plastisol) film coating
PVF(F) Polyvinylfluoride film coating PE(F) Polyethylene film coating PET(F) Polyethylene terephthalate film coating PP(F) Polypropylene film coating EXAMPLES Z275 PVDF PVDF paint coating, applied to steel sheet with hot-dip zinc coating. Nominal zinc coating mass 275 g/m² total, both sides. Z275 Hot-dip zinc coating, nominal coating mass 275 g/m² total, both sides. ZA255 Hot-dip 5 % Al-Zn alloy-coating, nominal coating mass 255 g/m² total, both sides. AZ185 Hot-dip 55 % Al-Zn alloy-coating, nominal coating mass 185 g/m² total, both sides 4 Requirements 4.1 General The product shall be manufactured from materials complying with 4.2. NOTE 1 The supplier of the materials is responsible for carrying out the tests necessary to verify that the materials supplied to the manufacturer comply with the requirements and should provide appropriate inspection documents (according to EN 10204) on request. NOTE 2 The symbols and abbreviations to be used to designate the steel grade, the type and mass of the metallic coating are those of the standards referred to in Clause 2. Product testing shall be provided to a defined schedule and carried out by the manufacturer or by an approved body. A permanent quality system shall be adopted by the manufacturer1).
1) E.g. quality management system based on EN ISO 9001. SIST EN 508-1:2008



EN 508-1:2008 (E) 15 4.2 Materials 4.2.1 Materials for roll formed and brake pressed profiles Material for self-supporting roll formed and brake pressed profiles shall be one of the grades of steel as specified in the appropriate material standard given in Table 1. Table 1 — Grades of steel Standard reference EN 10326 See 3.2.4 Metallic coating Zinc 5 % Al-Zn 55 % Al-Zn Al Permitted grades S220GD+Z a S250GD+Z a S280GD+Z S320GD+Z S350GD+Z S550GD+Z S220GD+ZA a S250GD+ZA a S280GD+ZA S320GD+ZA S350GD+ZA S550GD+ZA --------- S250GD+AZ a S280GD+AZ S320GD+AZ S350GD+AZ S550GD+AZ )
( see Annex A ) ( ) ( a Profiled sheets made from these grades may not be permitted for use in some countries. 4.2.2 Materials for tiles The steel grades shown in Table 2 shall be used for forming tiles when the grades given in Table 1 are not suitable because the manufacturing process requires specific forming qualities. Table 2 — Grades of steel
Standard reference EN 10327 Metallic coating Zinc 5 % Al-Zn 55 % Al-Zn Permitted grades DX51D+Z DX52D+Z DX53D+Z DX54D+Z DX51D+ZA DX52D+ZA DX53D+ZA DX54D
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.