Surgical and dental hand instruments - Determination of resistance against autoclaving, corrosion and thermal exposure (ISO 13402:1995)

Describes test methods to determine the resistance of stainless steel surgical and dental hand instruments against autoclaving, corrosion and thermal exposure.

Chirurgische und zahnärztliche Handinstrumente - Bestimmung der Beständigkeit gegenüber Sterilisation, Korrosion und Wärmebehandlung (ISO 13402:1995)

Diese Internationale Norm beschreibt Prüfverfahren zur Bestimmung der Beständigkeit rostfreier, chirurgischer und zahnärztlicher Handinstrumente gegen Sterilisation, Korrosion und Wärmebehandlung. Die Anforderungen für solche Prüfungen, zusammen mit der Anzahl der Durchläufe für jedes Prüfverfahren, sind in den Produktnormen definiert und festgelegt. Andere zusätzliche Prüfungen können auch gefordert werden (siehe Einleitung).

Instruments chirurgicaux et dentaires a main - Détermination de la résistance au passage a l'autoclave, a la corrosion et a l'exposition a la chaleur (ISO 13402:1995)

Surgical and dental hand instruments - Determination of resistance against autoclaving, corrosion and thermal exposure (ISO 13402:1995)

General Information

Status
Published
Publication Date
31-Oct-2001
Technical Committee
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
01-Nov-2001
Due Date
01-Nov-2001
Completion Date
01-Nov-2001

Buy Standard

Standard
EN ISO 13402:2001
English language
7 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Surgical and dental hand instruments - Determination of resistance against autoclaving, corrosion and thermal exposure (ISO 13402:1995)Chirurgische und zahnärztliche Handinstrumente - Bestimmung der Beständigkeit gegenüber Sterilisation, Korrosion und Wärmebehandlung (ISO 13402:1995)Instruments chirurgicaux et dentaires a main - Détermination de la résistance au passage a l'autoclave, a la corrosion et a l'exposition a la chaleur (ISO 13402:1995)Surgical and dental hand instruments - Determination of resistance against autoclaving, corrosion and thermal exposure (ISO 13402:1995)11.060.25Dental instruments11.040.30Operacijski instrumenti in materialiSurgical instruments and materialsICS:Ta slovenski standard je istoveten z:EN ISO 13402:2000SIST EN ISO 13402:2001en01-november-2001SIST EN ISO 13402:2001SLOVENSKI
STANDARD



SIST EN ISO 13402:2001



SIST EN ISO 13402:2001



SIST EN ISO 13402:2001



SIST EN ISO 13402:2001



SIST EN ISO 13402:2001



INTERNATIONAL STANDARD ISO 13402 First edition 1995-08-01 Surgical and dental hand instruments - Determination of resistance against autoclaving, corrosion and thermal exposure Instruments chirurgicaux et den taires A main - Determination de Ia ksistance au passage 2 I’autoclave, 2 Ia corrosion et a I’explosion 2 Ia chaleur Reference number ISO 13402: 1995(E) SIST EN ISO 13402:2001



ISO 13402:1995(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national Standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Esch member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. International Standard ISO 13402 was prepared by Technical Committee ISOnC 170, Surgical instruments. Annex A of this International Standard is for information only. 0 ISO 1995 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronrc or mechanical, including photocopying and microfilm, without Permission in writing from the publisher. Intern ational Organization for Standardization Case Postale 56 l CH-l 211 Geneve 20 l Switzerland Printed in Switzerland ii SIST EN ISO 13402:2001



0 ISO ISO 13402:1995(E) Introduction The procedures described in this International Standard are intended to form a harmonized series of tests that may be referred to, individually or in combination, in other separate product Standards. The requirements for such tests shall be defined and stated within the body of the product Standard along with the number of cycles for each test procedure. The tests apply to dental and surgical instruments and are already stan- dardized in relevant product Standards (e.g. ISO 7151, SurgicaI instru- men ts - Non-cutting, articula ted ins trumen ts - General requiremen ts and test methods; ISO 9173-1 Dental extraction forceps - Part 7: Screw andpin joint types). However, the test procedures as stated in the product Standards differ in minor details. An alignment and a compilation was es- tablished. The most important test methods for dental and surgical in- struments have been brought together in one general International Standard. Other, additional, tests may also be required in individual product stan- dards; those procedures and requirements will be determined by the members of the working groups concerned. When established, it is in- tended that these additional test procedures are incorporated in this International Standard as an addendum or at the next revision. This International Standard does not specify any test sequence nor any requirements related to specific instruments. The requirements, the test sequence and the number of test cycles have to be defined in the relevant product Standards or, if no Standard is available, it has to be left to the decision of the purchaser and/or the manufacturer. Apart from the boiling water test, the autoclave test applies for determin- ing corrosion resistance. In this sense, this International Standard specifies two test methods for determining corrosion resistance. When placing an Order, it is intended that the purchaser state whether both tests are to be carried out or which of the two tests. If the purchaser does not so indicate, the choice is left to the discretion of the manufacturer. . . . Ill SIST EN ISO 13402:2001



This page intentionally left blank SIST EN ISO 13402:2001



INTERNATIONAL STANDARD 0 ISO ISO 13402:1995(E) Surgical and dental hand instruments - Determination of resistance against autoclaving, corrosion and thermal exposure 1 Scope This International Standard describes test methods to determine the resistance of stainless steel surgical and dental hand instruments against autoclaving, cor- rosion and thermal exposure. The requirements for such tests are defined and stated in the product Standard along with the number of cycles for each test procedure. Other, additional, tests may also be required (see the Introduction). 2 Normative reference The following Standard contains provisions which, through reference in this text, constitute provisions of this International Standard. At the time of publi- cation, the edition indicated was valid. All Standards are subject to revision, and Parties to agreements based on this International Standard are encouraged to i
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.