Low-voltage electrical installations - Part 7-708: Requirements for special installations or location - Caravan parks, camping parks and similar locations

The particular requirements contained in this part of IEC 60364 apply only to circuits intended
to supply leisure accommodation vehicles, tents or residential park homes in caravan parks,
camping parks and similar locations.
NOTE For the purposes of this document caravan park includes camping parks and similar locations.
The particular requirements do not apply to the internal electrical installations of leisure
accommodation vehicles, mobile or transportable units or residential park homes.

Errichten von Niederspannungsanlagen - Teil 7-708: Anforderungen für Betriebsstätten, Räume und Anlagen besonderer Art - Caravanplätze, Campingplätze und ähnliche Bereiche

Installations électriques à basse tension - Partie 7-708: Exigences pour les installations ou emplacements particuliers - Parcs de caravanes, parcs de camping et emplacements analogues

EC 60364-7-708:2017 s’applique seulement aux circuits destinés à alimenter les véhicules de loisirs, les tentes et les habitations de parc résidentiel dans les parcs de caravanes, dans les parcs de camping et aux emplacements analogues. NOTE Pour les besoins du présent document, le terme "parc de caravanes" comprend "parcs de camping et emplacements analogues". Les exigences particulières ne s’appliquent pas aux installations électriques intérieures des véhicules de loisirs, des unités mobiles ou transportables ou habitations de parc résidentiel. Cette troisième édition annule et remplace la deuxième édition parue en 2007. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente: – les exigences pour la protection contre les chocs ont été modifiées: le matériel installé sur un emplacement de camping doit désormais être protégé contre les chocs de sévérité élevée AG3 (degré minimal de protection IK 08); – les socles de prise de courant et les connecteurs doivent désormais être verrouillés conformément aux normes de l’IEC afin d’éviter que les contacts femelles soient actifs lorsqu’ils sont accessibles.

Nizkonapetostne električne inštalacije - 7-708. del: Zahteve za posebne inštalacije ali lokacije - Električne inštalacije v avtokampih in podobnih lokacijah

Posebne zahteve, zajete v tem delu standarda IEC 60364, veljajo samo za vezja, namenjena za oskrbo bivalnih počitniških vozil, šotorov ali stanovanjskih domov v avtokampih, območjih za kampiranje in podobnih lokacijah.
OPOMBA V tem dokumentu avtokamp vključuje območja za kampiranje in podobne lokacije.
Posebne zahteve se ne uporabljajo za notranje električne inštalacije bivalnih počitniških vozil, premičnih ali prenosnih enot ali stanovanjskih domov.

General Information

Status
Published
Publication Date
20-Sep-2017
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
29-Aug-2017
Due Date
03-Nov-2017
Completion Date
21-Sep-2017

RELATIONS

Buy Standard

Standardization document
SIST HD 60364-7-708:2017
English language
15 pages
sale 10% off
Preview
sale 10% off
Preview

e-Library read for
1 day

Standards Content (sample)

SLOVENSKI STANDARD
SIST HD 60364-7-708:2017
01-oktober-2017
1DGRPHãþD
SIST HD 60364-7-708:2009

1L]NRQDSHWRVWQHHOHNWULþQHLQãWDODFLMHGHO=DKWHYH]DSRVHEQHLQãWDODFLMH

DOLORNDFLMH(OHNWULþQHLQãWDODFLMHYDYWRNDPSLKLQSRGREQLKORNDFLMDK

Low-voltage electrical installations - Part 7-708: Requirements for special installations or

location - Caravan parks, camping parks and similar locations

Errichten von Niederspannungsanlagen - Teil 7-708: Anforderungen für Betriebsstätten,

Räume und Anlagen besonderer Art - Caravanplätze, Campingplätze und ähnliche
Bereiche

Installations électriques à basse tension - Partie 7-708: Exigences pour les installations

ou emplacements particuliers - Parcs de caravanes, parcs de camping et emplacements

analogues
Ta slovenski standard je istoveten z: HD 60364-7-708:2017
ICS:
91.140.50 Sistemi za oskrbo z elektriko Electricity supply systems
97.200.30 Oprema za taborjenje in Camping equipment and
tabori camp-sites
SIST HD 60364-7-708:2017 en

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST HD 60364-7-708:2017
---------------------- Page: 2 ----------------------
SIST HD 60364-7-708:2017
HARMONIZATION DOCUMENT HD 60364-7-708
DOCUMENT D'HARMONISATION
HARMONISIERUNGSDOKUMENT
August 2017
ICS 91.140.50 Supersedes HD 60364-7-708:2009
English Version
Low-voltage electrical installations -
Part 7-708: Requirements for special installations or locations -
Caravan parks, camping parks and similar locations
(IEC 60364-7-708:2017)

Installations électriques à basse tension - Partie 7-708: Errichten von Niederspannungsanlagen - Teil 7-708:

Exigences pour les installations ou emplacements Anforderungen für Betriebsstätten, Räume und Anlagen

particuliers - Parcs de caravanes, parcs de camping et besonderer Art - Caravanplätze, Campingplätze und

emplacements analogues ähnliche Bereiche
(IEC 60364-7-708:2017) (IEC 60364-7-708:2017)

This Harmonization Document was approved by CENELEC on 2017-05-15. CENELEC members are bound to comply with the

CEN/CENELEC Internal Regulations which stipulate the conditions for implementation of this Harmonization Document at national level.

Up-to-date lists and bibliographical references concerning such national implementations may be obtained on application to the CEN-

CENELEC Management Centre or to any CENELEC member.

This Harmonization Document exists in three official versions (English, French, German).

CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,

Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,

Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,

Switzerland, Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels

© 2017 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.

Ref. No. HD 60364-7-708:2017 E
---------------------- Page: 3 ----------------------
SIST HD 60364-7-708:2017
HD 60364-7-708:2017
European foreword

The text of document 64/2162/FDIS, future edition 3 of IEC 60364-7-708, prepared by IEC/TC 64

"Electrical installations and protection against electric shock" was submitted to the IEC-CENELEC

parallel vote and approved by CENELEC as HD 60364-7-708:2017.
The following dates are fixed:
• latest date by which the document has to be implemented at (dop) 2018-02-18
national level by publication of an identical national
standard or by endorsement
• latest date by which the national standards conflicting with (dow) 2020-08-18
the document have to be withdrawn
This document supersedes HD 60364-7-708:2009.

Attention is drawn to the possibility that some of the elements of this document may be the subject of

patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.

Endorsement notice

The text of the International Standard IEC 60364-7-708:2017 was approved by CENELEC as a

Harmonization Document without any modification.

In the official version, for Bibliography, the following notes have to be added for the standards indicated:

IEC 60364-7-721 NOTE Harmonized as HD 60364-7-721.
IEC 61386-24 NOTE Harmonized as EN 61386-24.
---------------------- Page: 4 ----------------------
SIST HD 60364-7-708:2017
HD 60364-7-708:2017
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications

The following documents are referred to in the text in such a way that some or all of their content

constitutes requirements of this document. For dated references, only the edition cited applies. For

undated references, the latest edition of the referenced document (including any amendments)

applies.

NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod),

the relevant EN/HD applies.

NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is

available here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60038 - IEC standard voltages EN 60038 -
IEC 60309-1 1999 Plugs, socket-outlets and couplers for EN 60309-1 1999
industrial purposes - Part 1: General
+ A1 (mod) 2005 + A1 2007
requirements
+ A2 2012 + A2 2012
IEC 60309-2 - Plugs, socket-outlets and couplers for EN 60309-2 -
industrial purposes - Part 2: Dimensional
interchangeability requirements for pin
and contact-tube accessories
IEC 60309-4 (mod) 2006 Plugs, socket-outlets and couplers for EN 60309-4 2007
industrial purposes - Part 4: Switched
+ A1 2012 + A1 2012
socket-outlets and connectors with or
without interlock
IEC 60364-4-43 - Low voltage electrical installations – HD 60364-4-43 -
Part 4-43: Protection for safety -
Protection against overcurrent
IEC 62262 - Degrees of protection provided by EN 62262 -
enclosures for electrical equipment
against external mechanical impacts (IK
code)
---------------------- Page: 5 ----------------------
SIST HD 60364-7-708:2017
---------------------- Page: 6 ----------------------
SIST HD 60364-7-708:2017
IEC 60364-7-708
Edition 3.0 2017-04
INTERNATIONAL
STANDARD
Low-voltage electrical installations –
Part 7-708: Requirements for special installations or locations – Caravan parks,
camping parks and similar locations
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 91.140.50 ISBN 978-2-8322-4148-6

Warning! Make sure that you obtained this publication from an authorized distributor.

® Registered trademark of the International Electrotechnical Commission
---------------------- Page: 7 ----------------------
SIST HD 60364-7-708:2017
– 2 – IEC 60364-7-708:2017 © IEC 2017
CONTENTS

FOREWORD ........................................................................................................................... 3

INTRODUCTION ..................................................................................................................... 5

708 Caravan parks, camping parks and similar locations ........................................................ 6

708.1 Scope .............................................................................................................. 6

708.2 Normative references ....................................................................................... 6

708.3 Terms and definitions ....................................................................................... 6

708.31 Purposes, supplies and structure ..................................................................... 7

708.312 Conductor arrangement and system earthing ................................................... 7

708.313 Supplies ........................................................................................................... 7

708.4 Protection for safety ......................................................................................... 8

708.41 Protection against electric shock ...................................................................... 8

708.415 Additional protection ........................................................................................ 8

708.5 Selection and erection of electrical equipment.................................................. 8

708.51 Selection and erection of electrical equipment – Common rules ....................... 8

708.512 Operational conditions and external influences ................................................ 8

708.52 Wiring systems ................................................................................................. 9

708.521 Types of wiring systems ................................................................................... 9

708.533 Devices for protection against overcurrent ....................................................... 9

708.536 Isolation and switching ................................................................................... 10

708.55 Other equipment ............................................................................................ 10

Annex A (informative) List of notes concerning certain countries .......................................... 11

Bibliography .......................................................................................................................... 12

---------------------- Page: 8 ----------------------
SIST HD 60364-7-708:2017
IEC 60364-7-708:2017 © IEC 2017 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
LOW-VOLTAGE ELECTRICAL INSTALLATIONS –
Part 7-708: Requirements for special installations or locations –
Caravan parks, camping parks and similar locations
FOREWORD

1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising

all national electrotechnical committees (IEC National Committees). The object of IEC is to promote

international co-operation on all questions concerning standardization in the electrical and electronic fields. To

this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,

Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC

Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested

in the subject dealt with may participate in this preparatory work. International, governmental and non-

governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely

with the International Organization for Standardization (ISO) in accordance with conditions determined by

agreement between the two organizations.

2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international

consensus of opinion on the relevant subjects since each technical committee has representation from all

interested IEC National Committees.

3) IEC Publications have the form of recommendations for international use and are accepted by IEC National

Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC

Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any

misinterpretation by any end user.

4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications

transparently to the maximum extent possible in their national and regional publications. Any divergence

between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in

the latter.

5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity

assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any

services carried out by independent certification bodies.

6) All users should ensure that they have the latest edition of this publication.

7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and

members of its technical committees and IEC National Committees for any personal injury, property damage or

other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and

expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC

Publications.

8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is

indispensable for the correct application of this publication.

9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of

patent rights. IEC shall not be held responsible for identifying any or all such patent rights.

International Standard IEC 60364-7-708 has been prepared by IEC technical committee 64:

Electrical installations and protection against electric shock.

This third edition cancels and replaces the second edition published in 2007. This edition

constitutes a technical revision.

This edition includes the following significant technical changes with respect to the previous

edition:

– requirements to protect against impact has changed: equipment installed in a campsite

now has to be protected against impact of high severity AG3 (minimum degree of
protection IK 08);

– socket outlets and connectors are now required to be interlocked in accordance with IEC

standards to prevent the socket contacts being live when accessible.
---------------------- Page: 9 ----------------------
SIST HD 60364-7-708:2017
– 4 – IEC 60364-7-708:2017 © IEC 2017
The text of this standard is based on the following documents:
FDIS Report on voting
64/2162/FDIS 64/2186/RVD

Full information on the voting for the approval of this standard can be found in the report on

voting indicated in the above table.

This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.

The reader’s attention is drawn to the fact that Annex A lists all of the “in-some-country”

clauses on differing practices of a less permanent nature relating to the subject of this

standard.

A list of all parts in the IEC 60364 series, published under the general title Low-voltage

electrical installations, can be found on the IEC website.

Future standards in this series will carry the new general title as cited above. Titles of existing

standards in this series will be updated at the time of the next edition.

The committee has decided that the contents of this publication will remain unchanged until

the stability date indicated on the IEC website under "http://webstore.iec.ch" in the data

related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
A bilingual version of this publication may be issued at a later date.
---------------------- Page: 10 ----------------------
SIST HD 60364-7-708:2017
IEC 60364-7-708:2017 © IEC 2017 – 5 –
INTRODUCTION

For the purpose of this part (IEC 60364-7-708) the requirements of the general Parts 1 to 6 of

IEC 60364 apply.

The IEC 60364-7-7XX parts of IEC 60364 contain particular requirements for special

installations or locations which are based on the requirements of the general parts of

IEC 60364 (IEC 60364-1 to IEC 60364-6). These IEC 60364-7-7XX parts are considered in

conjunction with the requirements of the general parts.

The particular requirements of this part of IEC 60364 supplement, modify or replace certain of

the requirements of the general parts of IEC 60364 being valid at the time of publication of

this part. The absence of reference to the exclusion of a part or a clause of a general part

means that the corresponding clauses of t
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.