Plastics pipes and fittings - Characteristics for utilisation of non-virgin PVC-U, PP and PE materials

This Technical Specification specifies definitions and recommended characteristics and test methods for the utilisation of PVC-U, PP and PE non-virgin materials in pipes, fittings and ancillaries for both pressure and non-pressure piping systems. This Technical Specification specifies the conditions for utilisation of non-virgin material with and without agreed specification Non-virgin materials may be reformulated by the use of additives and processing techniques to meet an agreed specification. Typically the additives used would be stabilisers and pigments etc. The WG responsible for the product standard should consider the content of this document and only permit dosage levels which give compliance with the requirements of the product standard. Further, the WG should consider whether extra or more frequent product testing is relevant when using such material in the production of pipes and fittings in accordance with the relevant product standard. NOTE For the purpose of this specification the term pipes means extruded pipes, gutters and any parts of a fabricated fitting which is made from an extruded pipe. The term fitting means injection- and rotomoulded fittings and injection moulded parts of a fabricated fitting. For the recycling process, the testing and the use of the non-virgin material National and/or European regulations may apply.

Kunststoffrohrleitungen und Formstücke - Eigenschaften für die Verwendung von Rücklaufmaterial und Recyclat aus PVC-U-, PP- und PE-Materialien

Diese Technische Spezifikation legt Begriffe und empfohlene Eigenschaften und Prüfverfahren für die Verwendung von Umlauf-, Rücklaufmaterial und Rezyklat aus PVC U-, PP- und PE Materialien für Rohrleitungen, Formstücke und sonstige Bauteile sowohl für Druckrohrleitungssysteme als auch drucklose Rohrleitungssysteme fest.
Diese Technische Spezifikation legt die Bedingungen für die Verwendung von Umlauf-, Rücklaufmaterial und Rezyklat mit oder ohne eine vereinbarte Spezifikation fest.
Um eine vereinbarte Spezifikation zu erfüllen, können Rücklaufmaterialien und Rezyklat durch die Verwendung von Additiven und die Anwendung von Verarbeitungsverfahren in deren Zusammensetzung verändert werden. Üblicherweise werden Stabilisatoren, Pigmente usw. als Additive eingesetzt.
Die für die Produktnorm verantwortliche Arbeitsgruppe sollte den Inhalt des vorliegenden Dokuments unbedingt berücksichtigen und nur Einsatzmengen zulassen, die eine Übereinstimmung mit den Anforde-rungen der Produktnorm ergeben. Des Weiteren sollte die Arbeitsgruppe ernsthaft abwägen, ob zusätzliche oder häufiger stattfindende Produktprüfungen wichtig sind, wenn derartiges Material bei der Herstellung von Rohren und Formstücken nach der jeweiligen Produktnorm verwendet wird.
ANMERKUNG   Für die Anwendung dieser Spezifikation bezieht sich der Begriff Rohrleitungen auf extrudierte Rohr-leitungen, Abflussrinnen und alle Teile eines aus einem extrudierten Rohr gefertigten Formstückes. Der Begriff Formstück bezieht sich auf im Spritzguss- und Rotationsgussverfahren hergestellte Formstücke sowie im Spritzgussverfahren hergestellte Teile eines Formstückes.
Für den Recyclingprozess, die Prüfung und die Verwendung von Umlauf-, Rücklaufmaterial und Rezyklat können nationale und/oder europäische Vorschriften gelten.

Tubes et raccords en plastique - Caractéristiques pour l'utilisation de matières non vierges en PVC-U, PP et PE

La présente Spécification Technique spécifie des définitions, des caractéristiques recommandées et des méthodes d’essai pour l’utilisation de matières non vierges en PVC U, PP et PE dans des tubes, raccords et accessoires à la fois pour les systèmes de canalisation avec et sans pression.
La présente Spécification Technique spécifie les conditions d’utilisation de la matière non vierge avec ou sans spécification agréée.
Les matières non vierges peuvent être reformulées par l’utilisation d’additifs et de techniques de transformation afin de répondre à une spécification agréée. Les additifs communément utilisés consisteraient en stabilisants et pigments, etc.
Il convient que le GT responsable de la norme de produit étudie sérieusement le contenu de ce document et n’autorise que des niveaux de dosage assurant une conformité sûre aux exigences de la norme de produit. De plus, il convient que le GT examine sérieusement si des essais produits supplémentaires ou plus fréquents sont pertinents quand une telle matière est utilisée dans la production de tubes et raccords conformes à la norme de produit correspondante.
NOTE   Pour les besoins de la présente spécification, le terme « tubes » est employé pour désigner les tubes extrudés, les gouttières et toutes les parties d'un raccord façonné à partir d'un tube extrudé. Le terme « raccord » est employé pour désigner les raccords moulés par injection ou rotomoulés et les parties moulées par injection d'un raccord façonné.
Pour le recyclage, la soumission à essai et l’utilisation de matière non vierge, des réglementations Nationales et Européennes peuvent s’appliquer.

Polimerne cevi in fitingi - Lastnosti za uporabo obtočnega materiala, lastnega regenerata in regeneratov tujega izvora iz PVC-U, PP- in PE-materialov

Ta tehnična specifikacija določa definicije in priporočljive lastnosti in preskusne metode za uporabo obtočnega materiala tujega izvora iz PVC-U, PP- in PE-materialov za cevi, fitinge in pomožne dele za tlačne in netlačne cevne sisteme. Ta tehnična specifikacija določa pogoje za uporabo materialov tujega izvora z dogovorjeno specifikacijo in brez nje. Za skladnost z dogovorjeno specifikacijo so lahko materiali tujega izvora ponovno preoblikovani z uporabo dodatkov in obdelovalnih postopkov. Običajno so uporabljeni dodatki stabilizatorji, pigmenti itn. WG, ki je odgovoren za standard za izdelek, naj obravnava vsebino tega dokumenta in dovoli samo ravni doziranja, ki so skladne z zahtevami standarda za izdelek. Dodatno naj WG obravnava, ali so smotrna dodatna ali več pogostih preskušanj izdelka, ko je pri proizvodnji cevi in fitingov v skladu z zadevnim standardom za izdelek v uporabi omenjeni material. OPOMBA: Za namene te specifikacije izraz »cevi« označuje vlečene cevi, žlebove in druge dele fitinga, izdelanega iz vlečene cevi. Izraz »fiting« pomeni injekcijsko ali rotacijsko oblikovan fiting in injekcijsko oblikovane dele izdelanega fitinga. Za recikliranje, preskušanje in uporabo materiala tujega izvora veljajo nacionalni in/ali evropski predpisi.

General Information

Status
Withdrawn
Public Enquiry End Date
19-Sep-2012
Publication Date
13-Jun-2013
Withdrawal Date
06-Jun-2022
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
20-May-2022
Due Date
12-Jun-2022
Completion Date
07-Jun-2022

Relations

Buy Standard

Technical specification
TS CEN/TS 14541:2013
English language
10 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
Technical specification
kTS FprCEN/TS 14541:2012
English language
11 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST-TS CEN/TS 14541:2013
01-julij-2013
1DGRPHãþD
SIST-TS CEN/TS 14541:2007
3ROLPHUQHFHYLLQILWLQJL/DVWQRVWL]DXSRUDERREWRþQHJDPDWHULDODODVWQHJD
UHJHQHUDWDLQUHJHQHUDWRYWXMHJDL]YRUDL]39&833LQ3(PDWHULDORY
Plastics pipes and fittings - Characteristics for utilisation of non-virgin PVC-U, PP and PE
materials
Kunststoffrohrleitungen und Formstücke - Eigenschaften für die Verwendung von
Rücklaufmaterial und Recyclat aus PVC-U-, PP- und PE-Materialien
Tubes et raccords en plastique - Caractéristiques pour l'utilisation de matières non
vierges en PVC-U, PP et PE
Ta slovenski standard je istoveten z: CEN/TS 14541:2013
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
23.040.45 Fitingi iz polimernih Plastics fittings
materialov
SIST-TS CEN/TS 14541:2013 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST-TS CEN/TS 14541:2013

---------------------- Page: 2 ----------------------

SIST-TS CEN/TS 14541:2013


TECHNICAL SPECIFICATION
CEN/TS 14541

SPÉCIFICATION TECHNIQUE

TECHNISCHE SPEZIFIKATION
May 2013
ICS 23.040.20; 23.040.45 Supersedes CEN/TS 14541:2007
English Version
Plastics pipes and fittings - Characteristics for utilisation of non-
virgin PVC-U, PP and PE materials
Tubes et raccords en plastique - Caractéristiques pour Kunststoffrohrleitungen und Formstücke - Eigenschaften für
l'utilisation de matières non vierges en PVC-U, PP et PE die Verwendung von Rücklaufmaterial und Recyclat aus
PVC-U-, PP- und PE-Materialien
This Technical Specification (CEN/TS) was approved by CEN on 6 November 2012 for provisional application.

The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their
comments, particularly on the question whether the CEN/TS can be converted into a European Standard.

CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available
promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS)
until the final decision about the possible conversion of the CEN/TS into an EN is reached.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 14541:2013: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST-TS CEN/TS 14541:2013
CEN/TS 14541:2013 (E)
Contents Page
Foreword .3
1 Scope .4
2 Normative references .4
3 Terms, definitions and abbreviations .5
3.1 Terms and definitions .5
3.2 Abbreviations .5
4 Utilisation of non-virgin material for non-pressure application .5
4.1 Own reprocessed material .5
4.2 External reprocessed and recycled materials with agreed specification .5
4.3 External reprocessed and recycled materials without agreed specification .6
5 Utilisation of non-virgin material for pressure application .8
5.1 Own reprocessed material .8
5.2 External reprocessed and recycled materials with agreed specification .8
5.3 External reprocessed and recycled materials without agreed specification .8
6 General guidance for utilisation of non-virgin material .9
Bibliography . 10

2

---------------------- Page: 4 ----------------------

SIST-TS CEN/TS 14541:2013
CEN/TS 14541:2013 (E)
Foreword
This document (CEN/TS 14541:2013) has been prepared by Technical Committee CEN/TC 155 “Plastics
piping systems and ducting systems”, the secretariat of which is held by NEN.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes CEN/TS 14541:2007.
The main changes are:
— definitions brought in line with common practice;
— application “Pressure piping systems” is introduced;
— a general guidance has been added for utilisation of non-virgin materials;
— Annex A “Processing and performance of pipes and characteristics of recyclable material” is deleted.
According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following
countries are bound to announce this Technical Specification: Austria, Belgium, Bulgaria, Croatia, Cyprus,
Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,
Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
3

---------------------- Page: 5 ----------------------

SIST-TS CEN/TS 14541:2013
CEN/TS 14541:2013 (E)
1 Scope
This Technical Specification specifies definitions and recommended characteristics and test methods for the
utilisation of PVC-U, PP and PE non-virgin materials in pipes, fittings and ancillaries for both pressure and
non-pressure piping systems.
This Technical Specification specifies the conditions for utilisation of non-virgin material with and without
agreed specification
Non-virgin materials may be reformulated by the use of additives and processing techniques to meet an
agreed specification. Typically the additives used would be stabilisers and pigments etc.
The WG responsible for the product standard should consider the content of this document and only permit
dosage levels which give compliance with the requirements of the product standard. Further, the WG should
consider whether extra or more frequent product testing is relevant when using such material in the production
of pipes and fittings in accordance with the relevant product standard.
NOTE For the purpose of this specification the term pipes means extruded pipes, gutters and any parts of a
fabricated fitting which is made from an extruded pipe. The term fitting means injection- and rotomoulded fittings and
injection moulded parts of a fabricated fitting.
For the recycling process, the testing and the use of the non-virgin material National and/or European
regulations may apply.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
EN 12099, Plastics piping systems — Polyethylene piping materials and components — Determination of
volatile content
EN 10204:2004, Metallic products — Types of inspection documents
EN 15346:2007, Plastics  Recycled Plastics  Characterisation of poly(vinyl chloride) (PVC) recyclates
EN ISO 306, Plastics  Thermoplastic materials  Determination of Vicat softening temperature (VST)
(ISO 306)
EN ISO 13229, Thermoplastics piping systems for non-pressure applications — Unplasticized poly(vinyl
chloride) (PVC-U) pipes and fittings — Determination of the viscosity number and K-value (ISO 13229)
EN ISO 1133-1, Plastics — Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR)
of thermoplastics — Part 1: Standard method (ISO 1133-1)
EN ISO 1183-2, Plastics — Methods for determining the density of non-cellular plastics — Part 2: Density
gradient column method (ISO 1183-2)
EN ISO 3451-1:2008, Plastics — Determination of ash — Part 1: General method (ISO 3451-1:2008)
EN ISO 3451-5, Plastics — Determination of ash — Part 5: Poly(vinyl chloride) (ISO 3451-5)
EN ISO 11357-6, Plastics — Differential scanning calorimetry (DSC) — Part 6: Determination of oxidation
induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT) (ISO 11357-6)
4

---------------------- Page: 6 ----------------------

SIST-TS CEN/TS 14541:2013
CEN/TS 14541:2013 (E)
3 Terms, definitions and abbreviations
3.1 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1.1
virgin material
material in the form such as granules or powder th
...

SLOVENSKI STANDARD
kSIST-TS FprCEN/TS 14541:2012
01-september-2012
3ROLPHUQHFHYLLQILWLQJL/DVWQRVWL]DXSRUDERREWRþQHJDPDWHULDODODVWQHJD
UHJHQHUDWDLQUHJHQHUDWRYWXMHJDL]YRUDL]39&833LQ3(PDWHULDORY
.RPSOHPHQWDUQLHOHPHQW
Plastics pipes and fittings - Characteristics for utilisation of non-virgin PVC-U, PP and PE
materials - Complementary element
Kunststoffrohrleitungen und Formstücke - Eigenschaften für die Verwendung von
Rücklaufmaterial und Recyclat aus PVC-U-, PP- und PE-Materialien - Ergänzendes
Element
Tubes et raccords en plastique - Caractéristiques pour l'utilisation de matières non
vièrges en PVC-U, PP et PE
Ta slovenski standard je istoveten z: FprCEN/TS 14541
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
23.040.45 Fitingi iz polimernih Plastics fittings
materialov
kSIST-TS FprCEN/TS 14541:2012 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

kSIST-TS FprCEN/TS 14541:2012

---------------------- Page: 2 ----------------------

kSIST-TS FprCEN/TS 14541:2012


TECHNICAL SPECIFICATION
FINAL DRAFT
FprCEN/TS 14541
SPÉCIFICATION TECHNIQUE

TECHNISCHE SPEZIFIKATION

July 2012
ICS 23.040.20; 23.040.45 Will supersede CEN/TS 14541:2007
English Version
Plastics pipes and fittings - Characteristics for utilisation of non-
virgin PVC-U, PP and PE materials - Complementary element
Tubes et raccords en plastique - Caractéristiques pour Kunststoffrohrleitungen und Formstücke - Eigenschaften für
l'utilisation de matières non vièrges en PVC-U, PP et PE die Verwendung von Rücklaufmaterial und Recyclat aus
PVC-U-, PP- und PE-Materialien - Ergänzendes Element


This draft Technical Specification is submitted to CEN members for formal vote. It has been drawn up by the Technical Committee CEN/TC
155.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.

Warning : This document is not a Technical Specification. It is distributed for review and comments. It is subject to change without notice
and shall not be referred to as a Technical Specification.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. FprCEN/TS 14541:2012: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

kSIST-TS FprCEN/TS 14541:2012
FprCEN/TS 14541:2012 (E)
Contents Page
Foreword .3
1 Scope .4
2 Normative references .4
3 Terms, definitions and abbreviations .5
3.1 Terms and definitions .5
3.2 Abbreviations .5
4 Utilization of non-virgin material for non-pressure application .6
4.1 Own reprocessed material .6
4.2 External reprocessed and recycled materials with agreed specification .6
4.3 External reprocessed and recycled materials without agreed specification .6
5 Utilization of non-virgin material for pressure application .9
5.1 Own reprocessed material .9
5.2 External reprocessed and recycled materials with agreed specification .9
5.3 External reprocessed and recycled materials without agreed specification .9
6 General guidance for utilization of non-virgin material . 10
Bibliography . 11

2

---------------------- Page: 4 ----------------------

kSIST-TS FprCEN/TS 14541:2012
FprCEN/TS 14541:2012 (E)
Foreword
This document (FprCEN/TS 14541:2012) has been prepared by Technical Committee CEN/TC 155 “Plastics
piping systems and ducting systems”, the secretariat of which is held by NEN.
This document is currently submitted to the Formal Vote.
This document will supersede CEN/TS 14541:2007.
The main changes are:
— definitions brought in line with common practice;
— application “Pressure piping systems” is introduced:
— a general guidance has been added for utilization of non-virgin materials:
— Annex A “Processing and performance of pipes and characteristics of recyclable material” is deleted.
3

---------------------- Page: 5 ----------------------

kSIST-TS FprCEN/TS 14541:2012
FprCEN/TS 14541:2012 (E)
1 Scope
This Technical Specification specifies definitions and recommended characteristics and test methods for the
utilisation of PVC-U, PP and PE non-virgin materials in pipes, fittings and ancillaries for both pressure and
non-pressure piping systems.
This Technical Specification specifies the conditions for utilisation of non-virgin material with and without
agreed specification
Non-virgin materials may be reformulated by the use of additives and processing techniques to meet an
agreed specification. Typically the additives used would be stabilisers and pigments etc.
The WG responsible for the product standard should seriously consider the content of this document and only
permit dosage levels which give compliance with the requirements of the product standard. Further, the WG
should seriously consider whether extra or more frequent product testing is relevant when using such material
in the production of pipes and fittings in accordance with the relevant product standard.
NOTE For the purpose of this specification the term pipes means extruded pipes, gutters and any parts of a
fabricated fitting which is made from an extruded pipe. The term fitting means injection- and rotomoulded fittings and
injection moulded parts of a fabricated fitting.
For the recycling process, the testing and the use of the non-virgin material National and/or European
regulations may apply.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
EN 727, Plastics piping and ducting systems — Thermoplastics pipes and fittings — Determination of Vicat
softening temperature (VST)
EN 12099, Plastics piping systems — Polyethylene piping materials and components — Determination of
volatile content
EN 10204:2004, Metallic products — Types of inspection documents
EN 15346:2007, Plastics  Recycled Plastics  Characterisation of poly(vinyl chloride) (PVC) recyclates
EN ISO 13229, Thermoplastics piping systems for non-pressure applications — Unplasticized poly(vinyl
chloride) (PVC-U) pipes and fittings — Determination of the viscosity number and K-value (ISO 13229)
EN ISO 1133-1, Plastics — Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR)
of thermoplastics — Part 1: Standard method (ISO 1133-1)
EN ISO 1133-2, Plastics — Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR)
of thermoplastics — Part 2: Method for materials sensitive to time-temperature history and/or moisture (ISO
1133-2)
EN ISO 1183-2, Plastics — Methods for determining the density of non-cellular plastics — Part 2: Density
gradient column method (ISO 1183-2)
EN ISO 3451-1:2008, Plastics — Determination of ash — Part 1: General method (ISO 3451-1:2008)
4

---------------------- Page: 6 ----------------------

kSIST-TS FprCEN/TS 14541:2012
FprCEN/TS 14541:2012 (E)
EN ISO 3451-5, Plastics — Determination of ash — Part 5: Poly(vinyl chloride) (ISO 3451-5)
3 Terms, definitions and abbreviations
3.1 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1.1
virgin material
material in the form such as granules or powder that have not been subjected to use or processing other than
that required for their manufacture and to which no reprocessed or recycled materi
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.