SIST EN IEC 61918:2019/A2:2024
(Amendment)Amendment 2 - Industrial communication networks - Installation of communication networks in industrial premises (IEC 61918:2018/AMD2:2024)
Amendment 2 - Industrial communication networks - Installation of communication networks in industrial premises (IEC 61918:2018/AMD2:2024)
Industrielle Kommunikationsnetze - Installation von Kommunikationsnetzen in Industrieanlagen (IEC 61918:2018/AMD2:2024)
Amendement 2 - Réseaux de communication industriels - Installation de réseaux de communication dans des locaux industriels (IEC 61918:2018/AMD2:2024)
Industrijska komunikacijska omrežja - Inštalacija komunikacijskih omrežij v industrijskih okoljih - Dopolnilo A2 (IEC 61918:2018/AMD2:2024)
General Information
Relations
Buy Standard
Standards Content (Sample)
SLOVENSKI STANDARD
01-september-2024
Industrijska komunikacijska omrežja - Inštalacija komunikacijskih omrežij v
industrijskih okoljih - Dopolnilo A2 (IEC 61918:2018/AMD2:2024)
Amendment 2 - Industrial communication networks - Installation of communication
networks in industrial premises (IEC 61918:2018/AMD2:2024)
Industrielle Kommunikationsnetze - Installation von Kommunikationsnetzen in
Industrieanlagen (IEC 61918:2018/AMD2:2024)
Amendement 2 - Réseaux de communication industriels - Installation de réseaux de
communication dans des locaux industriels (IEC 61918:2018/AMD2:2024)
Ta slovenski standard je istoveten z: EN IEC 61918:2018/A2:2024
ICS:
25.040.40 Merjenje in krmiljenje Industrial process
industrijskih postopkov measurement and control
35.110 Omreževanje Networking
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN IEC 61918:2018/A2
NORME EUROPÉENNE
EUROPÄISCHE NORM April 2024
ICS 25.040.40; 33.020; 35.240.50
English Version
Industrial communication networks - Installation of
communication networks in industrial premises
(IEC 61918:2018/AMD2:2024)
Réseaux de communication industriels - Installation de Industrielle Kommunikationsnetze - Installation von
réseaux de communication dans des locaux industriels Kommunikationsnetzen in Industrieanlagen
(IEC 61918:2018/AMD2:2024) (IEC 61918:2018/AMD2:2024)
This amendment A2 modifies the European Standard EN IEC 61918:2018; it was approved by CENELEC on 2024-04-19. CENELEC
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this amendment the
status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as
the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Türkiye and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2024 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 61918:2018/A2:2024 E
European foreword
The text of document 65C/1282/FDIS, future IEC 61918/AMD2, prepared by SC 65C "Industrial
networks" of IEC/TC 65 "Industrial-process measurement, control and automation" was submitted to
the IEC-CENELEC parallel vote and approved by CENELEC as EN IEC 61918:2018/A2:2024.
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2025-01-19
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2027-04-19
document have to be withdrawn
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 61918:2018/AMD2:2024 was approved by CENELEC as a
European Standard without any modification.
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cencenelec.eu.
The Annex ZA of EN IEC 61918:2018 applies with the following changes:
Publication Year Title EN/HD Year
Delete the following reference:
IEC 60603 series Connectors for electronic equipment EN 60603 series
Add the following new references:
IEC 61076-2-104 - Connectors for electronic equipment - EN 61076-2-104 -
Product requirements - Part 2-104: Circular
connectors - Detail specification for circular
connectors with M8 screw-locking or snap-
locking
IEC 61076-2-114 - Connectors for electrical and electronic EN IEC 61076-2-114 -
equipment - Product requirements - Part 2-
114: Circular connectors - Detail
specification for connectors with M8 screw-
locking with power contacts and signal
contacts for data transmission up to 100
MHz
IEC 61076-3-122 - Connectors for electrical and electronic EN IEC 61076-3-122 -
equipment - Product requirements - Part 3-
122: Detail specification for 8-way,
shielded, free and fixed connectors for I/O
and data transmission with frequencies up
to 500 MHz and current-carrying capacity
in industrial environments
IEC 61076-3-124 - Connectors for electrical and electronic EN IEC 61076-3-124 -
equipment - Product requirements - Part 3-
124: Rectangular connectors - Detail
specification for 10-way, shielded, free and
fixed connectors for I/O and data
transmission with frequencies up to 500
MHz
IEC 61156-13 2023 Multicore and symmetrical pair/quad - -
cables for digital communications - Part 13:
Symmetrical single pair cables with
transmission characteristics up to 20 MHz -
Horizontal floor wiring - Sectional
specification
Replace the existing reference to IEC 61158-2:2014 with the following new reference:
IEC 61158-2 2023 Industrial communication networks - EN IEC 61158-2 2023
Fieldbus specifications - Part 2: Physical
layer specification and service definition
Replace the existing reference to IEC 61784-1:— with the following new reference:
IEC 61784-1-x - Industrial networks - Profiles - Part 1-x: EN IEC 61784-1-x -
Fieldbus profiles
Replace the existing reference to IEC 61784-2:— with the following new reference
IEC 61784-2-x - Industrial networks - Profiles - Part 2-x: EN IEC 61784-2-x -
Additional real-time fieldbus profiles based
on ISO/IEC/IEEE 8802-3
Add the following new references:
IEC 63171-2 2021 Connectors for electrical and electronic - -
equipment - Part 2: Detail specification for
2-way, shielded or unshielded, free and
fixed connectors: mechanical mating
information, pin assignment and additional
requirements for type 2
IEC 63171-5 2022 Connectors for electrical and electronic EN IEC 63171-5 2022
equipment - Part 5: Detail specification for
2-way M8 and M12 circular connectors,
shielded or unshielded, free and fixed -
Mechanical mating information, pin
assignment and additional requirements for
Type 5
Delete the following reference:
ISO/IEC TR 11801-2017 Information technology - Generic cabling - -
9902 for customer premises - Part 9902:
Specifications for End-to-end link
configurations
Replace the existing references to ISO/IEC 14763-2:2012 and ISO/IEC 14763-2:2012/AMD1:2015
with the following new reference:
ISO/IEC 14763-2 2019 Information technology - Implementation - -
and operation of customer premises
cabling - Part 2: Planning and installation
Replace the existing references to ISO/IEC 14763-3:2014 with the following new reference:
ISO/IEC 14763-3 2014 Information technology - Implementation - -
and operation of customer premises
cabling - Part 3: Testing of optical fibre
cabling
AMD1 2018 - -
Replace the existing references to ISO/IEC 14763-4:2018 with the following new reference:
ISO/IEC 14763-4 2021 Information technology - Implementation - -
and operation of customer premises
cabling - Part 4: Measurement of end-to-
end (E2E)-Links, modular plug terminated
links (MPTL) and direct attach cabling
Add the following new reference:
ISO/IEC TS 29125 2017 Information Technology - - -
Telecommunications cabling requirements
for remote powering of terminal equipment
AMD1 2020
Replace the existing reference to IEEE Std 802.3-2015 and the reference to IEEE Std 802.3cg added
by IEC 61918:2018/AMD1:2022 with the following new reference and notes:
IEEE Std 802.3 2022 IEEE Standard for Ethernet - -
NOTE 1 The contents of IEEE Std 802.3cg have been integrated in IEEE Std 802.3-2022,
Clause 146.
NOTE 2 Physical Layer specifications for 100BASE-T1 and 1000BASE-T1 are provided in
IEEE Std 802.3-2022, Clause 96 and Clause 97 respectively.
IEC 61918 ®
Edition 4.0 2024-03
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
AMENDMENT 2
AMENDEMENT 2
Industrial communication networks – Installation of communication networks in
industrial premises
Réseaux de communication industriels – Installation de réseaux de
communication dans des locaux industriels
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 25.040.40, 33.020, 35.240.50 ISBN 978-2-8322-8280-9
– 2 – IEC 61918:2018/AMD2:2024
© IEC 2024
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
INDUSTRIAL COMMUNICATION NETWORKS – INSTALLATION
OF COMMUNICATION NETWORKS IN INDUSTRIAL PREMISES
AMENDMENT 2
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC Publication(s)"). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) IEC draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). IEC takes no position concerning the evidence, validity or applicability of any claimed patent rights in
respect thereof. As of the date of publication of t
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.