EN 13507:2010
(Main)Thermal spraying - Pre-treatment of surfaces of metallic parts and components for thermal spraying
Thermal spraying - Pre-treatment of surfaces of metallic parts and components for thermal spraying
This European Standard specifies the processing of surface preparation for thermal spraying. Important principles indicated in this European Standard should be taken into consideration when surfaces of metallic parts are to be prepared for thermal spraying. This European Standard applies for production of new parts as well as for the repair of worn parts.
This European Standard does not apply for thermal spraying in the case of protection against atmospheric corrosion by coatings of zinc and/or aluminium and their alloys, for which EN ISO 2063 applies.
Thermisches Spritzen - Vorbehandlung von Oberflächen metallischer Werkstücke und Bauteile für das thermische Spritzen
Diese Europäische Norm legt die Vorgehensweise zur Vorbereitung von Oberflächen zum thermischen Spritzen fest. Wichtige Grundsätze, die in dieser Europäischen Norm angegeben sind, sollten berücksichtigt werden, wenn Oberflächen metallischer Bauteile zum thermischen Spritzen vorzubereiten sind. Diese Europäische Norm gilt sowohl für die Neufertigung als auch für das Instandset¬zen verschlissener Teile.
Diese Europäische Norm gilt nicht für das thermische Spritzen zum Schutz gegen atmosphärische Korrosion durch Schichten aus Zink und/oder Aluminium und deren Legierungen, dafür gilt EN ISO 2063.
Projection thermique - Traitement préalable de surface de pièces et composants métalliques pour projection thermique
La présente Norme européenne spécifie les opérations associées à la préparation des surfaces destinées à recevoir un revêtement obtenu par projection thermique. Il convient que les principes importants indiqués dans la présente Norme européenne soient pris en considération lors de la préparation des surfaces métalliques destinées à être traitées par projection thermique. La présente Norme européenne s’applique à la fois à la production de nouvelles pièces et à la réparation de pièces usées.
Cette Norme européenne ne s‘applique pas à la projection thermique dans le cas de protection contre la corrosion atmosphérique par des revêtements de zinc et/ou d’aluminium et leurs alliages pour lesquels l’EN ISO 2063 est applicable.
Vroče brizganje - Predobdelava površin kovinskih delov in komponent za vroče brizganje
Ta evropski standard določa postopek priprave površine za vroče brizganje. Pomembna načela, navedena v tem evropskem standardu, je potrebno upoštevati pri pripravi površin kovinskih delov za vroče brizganje. Ta evropski standard se uporablja za proizvodnjo novih delov, kot tudi za popravilo obrabljenih delov. Ta evropski standard se ne uporablja za vroče brizganje v primeru zaščite pred atmosfersko korozijo s prevleko iz cinka in/ali aluminija ter njunih zlitin, za katere se uporablja EN ISO 2063.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.EUL]JDQMHThermisches Spritzen - Vorbehandlung von Oberflächen metallischer Werkstücke und Bauteile für das thermische SpritzenProjection thermique - Traitement préalable de surface de pièces et composants métalliques pour projection thermiquesThermal spraying - Pre-treatment of surfaces of metallic parts and components for thermal spraying25.220.20Površinska obdelavaSurface treatment25.220.10Priprava površineSurface preparationICS:Ta slovenski standard je istoveten z:EN 13507:2010SIST EN 13507:2010en,de01-april-2010SIST EN 13507:2010SLOVENSKI
STANDARDSIST EN 13507:20021DGRPHãþD
SIST EN 13507:2010
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 13507
February 2010 ICS 25.220.10 Supersedes EN 13507:2001English Version
Thermal spraying - Pre-treatment of surfaces of metallic parts and components for thermal spraying
Projection thermique - Traitement préalable de surface de pièces et composants métalliques pour projection thermiques
Thermisches Spritzen - Vorbehandlung von Oberflächen metallischer Werkstücke und Bauteile für das thermische Spritzen This European Standard was approved by CEN on 9 January 2010.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2010 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 13507:2010: ESIST EN 13507:2010
EN 13507:2010 (E) 2 Contents Page Foreword .31Scope .42Normative references .43Principles .44Methods of surface preparation .54.1General .54.2Degreasing .54.3Grit blasting .54.4Threading/grooving .74.5Cleaning by reversed transferred arc .74.6Bond coatings .74.7Precautions for health, safety and environmental protection .75Preheating .76Masking of areas not to be coated .87Effect of pre-treatment on the fatigue strength .8Bibliography .9 SIST E
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.