EN 15619:2008
(Main)Rubber or plastic coated fabrics - Safety of temporary structures (tents) - Specification for coated fabrics intended for tents and related structures
Rubber or plastic coated fabrics - Safety of temporary structures (tents) - Specification for coated fabrics intended for tents and related structures
This European Standard specifies the characteristics, requirements and test methods for coated fabric intended for mobile, temporary installed tents (see 3.3) and related structures.
Plastic film and material other than coated fabrics are not covered by this European Standard.
Mit Kautschuk oder Kunststoff beschichtete Textilien - Sicherheit Fliegender Bauten (Zelte) - Spezifikation für beschichtete Textilien für Zelte und zugehörige Bauten
Diese Europäische Norm legt die Eigenschaften, Anforderungen und Prüfverfahren für beschichtete Textilien
fest, die als wiederholt zu errichtende Fliegende Bauten in Form von Zelten (siehe 3.3) und zugehörige
Bauwerke vorgesehen sind.
Kunststofffolien und andere Materialien als beschichtete Textilien sind kein Bestandteil der vorliegenden
Norm.
Supports textiles revêtus de caoutchouc ou de plastique - Sécurité des structures temporaires (tentes) - Spécification des supports textiles revêtus destinés aux tentes et structures similaires
La présente Norme européenne spécifie les caractéristiques, les exigences et les méthodes d'essai relatives
aux étoffes enduites destinées aux tentes mobiles installées temporairement (voir 3.3) et aux structures
similaires.
Les films plastiques et les matériaux autres que les étoffes enduites ne sont pas couverts par la présente
Norme européenne.
Gumirane ali plastificirane tekstilije - Varnost začasnih konstrukcij (šotori) - Specifikacija tekstilij, namenjenih za šotore in podobne konstrukcije
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.FLMHMit Kautschuk oder Kunststoff beschichtete Textilien - Sicherheit Fliegender Bauten (Zelte) - Spezifikation für beschichtete Textilien für Zelte und zugehörige BautenSupports textiles revêtus de caoutchouc ou de plastique - Sécurité des structures temporaires (tentes) - Spécification des supports textiles revêtus destinés aux tentes et structures similairesRubber or plastic coated fabrics - Safety of temporary structures (tents) - Specification for coated fabrics intended for tents and related structures97.200.30Oprema za taborjenje in taboriCamping equipment and camp-sites59.080.40WHNVWLOLMHCoated fabricsICS:Ta slovenski standard je istoveten z:EN 15619:2008SIST EN 15619:2009en,fr,de01-april-2009SIST EN 15619:2009SLOVENSKI
STANDARD
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 15619October 2008ICS 59.080.40; 97.200.30 English VersionRubber or plastic coated fabrics - Safety of temporary structures(tents) - Specification for coated fabrics intended for tents andrelated structuresSupports textiles revêtus de caoutchouc ou de plastique -Sécurité des structures temporaires (tentes) - Spécificationdes supports textiles revêtus destinés aux tentes etstructures similairesMit Kautschuk oder Kunststoff beschichtete Textilien -Sicherheit Fliegender Bauten (Zelte) - Spezifikation fürbeschichtete Textilien für Zelte und zugehörige BautenThis European Standard was approved by CEN on 24 August 2008.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2008 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 15619:2008: ESIST EN 15619:2009
Artificial ageing by long term exposure to the combination of UV irradiation, elevated temperature and water.12 Annex B (normative)
Coating adhesion.14 Annex C (normative)
Elongation under load and residual deformation.16 Annex D (informative)
Weld resistance recommendation.18 Annex E (informative)
Assessment of conformity.20 Bibliography.23
EN 13782. This European Standard has been drawn up according to past experience and risk analysis. The content of this European Standard collects the different existing national regulations and refers to the different European test standards available for coated fabrics.
This European Standard also introduces a system of levels. It is not possible to divide coated fabric for tents into just a few performance levels, because of the enormous variety of conditions of use. This European Standard proposes different level of performance (A, B, C) for each characteristic – or T1, T2, T3, T4 for the fire behaviour. This allows to choose the appropriate level for each characteristic and so to compose a "product profile", adapted to each specific type of use. This means that for small tents exposed to low wind and snow loads but high exposition to sun light, a mechanical resistance level C may be required combined with a colour fastness level A. The level system should absolutely not be interpreted as if a coated fabric for tents needs to be rated "A" for all properties in order to obtain a "class" A. This European standard specifies requirements which are useful at design, calculation, manufacture, installation, maintenance, operation, examination and testing of coated fabric.
1 Scope This European Standard specifies the characteristics, requirements and test methods for coated fabric intended for mobile, temporary installed tents (see 3.3) and related structures.
Plastic film and material other than coated fabrics are not covered by this European Standard. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 1875-3, Rubber- or plastics- coated fabrics — Determination of tear strength — Part 3: Trapezoidal method EN 12280-1, Rubber- or plastics- coated fabrics - Acceleratd ageing tests — Part 1: Heat ageing EN 13782, Temporary structures – Tents – Safety EN 14115, Textiles — Burning behaviour of materials for marquees, large tents and related products — Ease of ignition EN 20105-A02, Textiles — Tests for colour fastness — Part A02: Grey scale for assessing change in colour (ISO 105-A02:1993) EN ISO 846, Plastics — Evaluation of the action of microorganisms (ISO 846:1997) EN ISO 1421, Rubber- or plastics-coated fabrics – Determination of tensile strength and elongation at break (ISO 1421:1998) EN ISO 2231, Rubber- or plastics-coated fabrics – Standard atmospheres for conditioning and testing (ISO 2231:1989) EN ISO 2286-2, Rubber- or plastics-coated fabrics – Determination of roll characteristics – Part 2: Methods for determination of total mass per unit area, mass per unit area of coating and mass per unit area of substrate (ISO 2286-2:1998) EN ISO 2411, Rubber- or plastics-coated fabrics – Determination of coating adhesion (ISO 2411:2000) EN ISO 4892-3, Plastics — Methods of exposure to laboratory light sources – Part 3: Fluorescent UV lamps (ISO 4892-3:2006) EN ISO 11925-2:2002, Reaction to fire tests – Ignitability of building products subjected to direct impingement of flame — Part 2: Single-flame source test (ISO 11925-2:2002) ISO 1420, Rubber- or plastics-coated fabrics – Determination of resistance to penetration by water 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. SIST EN 15619:2009
Key 1
top coating 2
fabric
coating
Figure 1 — Schema of a cross section of a woven fabric coated on both sides SIST EN 15619:2009
5.3 Tear strength In order to assess the risk of propagation of a tear due to lack of quality of the coated fabric or to an accident, the tear strength performances of a coated fabric shall be measured according to EN 1875-3 and declared by the manufacturer. 5.4 Coating adhesion The adhesion between the base fabric and the coating layer of the membrane material shall be assumed by coating adhesion tests according to Annex B. 5.5 Dimensional stability
During its life the tent membrane made up of coated fabric is submitted to many environmental loads (wind, snow, rain) and many mounting and dismantling of the structure. In order to limit any dimensional change of the membrane panels during the life of the tent, the fabric shall be dimensionally stable. The dimensional stability of the fabric shall be measured in both directions according to the test method described in C.1. For tents exposed to elevated temperatures during their use, an optional test is proposed in Annex C including a heat exposure (C.2) before mechanical loading. 5.6 Colour fastness to weathering and light The samples are exposed according to Annex A. Colour fastness is assessed by comparison with the grey scale and the specimens exposed for 2000 h to artificial ageing and the non-exposed specimens. The ageing procedure detailed in Annex A is based on EN ISO 4892-3 exposure mode 1 (UV, moisture cycle, and elevated temperature) that simulate the outdoor natural ageing.
5.7 Susceptibility to the development of microorganisms
In some climatic and environmental conditions, microorganisms may fix and develop on the surface of the coating. Their presence may damage the coating layer itself (discoloration, degradation of plastic coating) and may also hinder the use of the coated fabric membrane. The manufacturer of the coated fabric shall ensure that the coated fabric is treated with adapted treatment or sufficiently resistant to the action of microorganisms according to EN ISO 846. 5.8 Appearance Inspection of the appearance of membrane is important not only from an aesthetic point of view, but also from the aspect of examining for the presence of defects causing structural problems and of obstructions during usage. Appearance should be visually inspected on microscopic images taken under appropriate lighting at x SIST EN 15619:2009
The inspection items include: a) thickness of protective coating on the surface of yarns;
b) defects on yarns and their arrangement;
c) cracki
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.