EN 1263-1:2014

Temporary works equipment - Safety nets - Part 1: Safety requirements, test methods

This European Standard applies to safety nets and their accessories for use in construction and assembly work to protect from deeper fall. It specifies safety requirements and test methods and is based on the performance characteristics of polypropene and polyamide fibres. Materials used in nets should have no significant reduction in mechanical properties between –10 °C and +40 °C.
This European Standard is not applicable to the installation of safety nets. For a European Standard covering the installation of safety nets, see EN 1263 2.

Temporäre Konstruktionen für Bauwerke - Schutznetze (Sicherheitsnetze) - Teil 1: Sicherheitstechnische Anforderungen, Prüfverfahren

Diese Europäische Norm gilt für Schutznetze und Schutznetzzubehör, die bei Bau- und Montagearbeiten Verwendung zum Schutz gegen tieferen Absturz finden. Sie legt sicherheitstechnische Anforderungen und Prüfverfahren fest und basiert auf den Verhaltenseigenschaften von Polypropylen- und Polyamidfasern. Die für Schutznetze verwendeten Materialien sollten keine wesentlichen Verminderungen der mechanischen Eigenschaften zwischen 10 °C und 40 °C aufweisen.
Diese Europäische Norm gilt nicht die Errichtung von Schutznetzen fest. Für die Errichtung von Schutznetzen siehe EN 1263-2.

Équipements temporaires de chantiers - Filets de sécurité - Partie 1 : Exigences de sécurité, méthodes d'essai

Začasne konstrukcije za gradnjo - Varovalne mreže - 1. del: Varnostne zahteve, preskusne metode

Ta evropski standard velja za varovalne mreže in njihove priključke, ki se uporabljajo pri gradnji in montaži kot zaščita pred padcem z večje višine. Določa varnostne zahteve in preskusne metode ter temelji na kakovostnih lastnostih polipropenskih in poliamidnih vlaken. Mehanske lastnosti materialov, uporabljenih v mrežah, naj se ne bi bistveno zmanjšale pri temperaturah od –10 °C in +40 °C.
Ta evropski standard se ne uporablja za nameščanje varovalnih mrež. Za evropski standard, ki zajema nameščanje varovalnih mrež, glej EN 1263-2.

General Information

• Status: Published
• Publication Date: 16-Dec-2014
• Withdrawal Date: 29-Jun-2015
• ICS: 13.340.60 - Protection against falling and slipping
• ICS: 13.340.99 - Other protective equipment
• Technical Committee: CEN/TC 53 - Temporary works equipment
• Drafting Committee: CEN/TC 53/WG 7 - Specification for safety nets
• Current Stage: 9093 - Decision to confirm - Review Enquiry
• Completion Date: 04-Jun-2020
• Ref Project: SIST EN 1263-1:2015 - Temporary works equipment - Safety nets - Part 1: Safety requirements, test methods

Relations

• Replaces: EN 1263-1:2002 - Safety nets - Part 1: Safety requirements, test methods
• Effective Date: 11-Jul-2012

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Temporäre Konstruktionen für Bauwerke - Schutznetze (Sicherheitsnetze) - Teil 1: Sicherheitstechnische Anforderungen, PrüfverfahrenÉquipements temporaires de chantiers - Filets de sécurité - Partie 1 : Exigences de sécurité, méthodes d'essaiTemporary works equipment - Safety nets - Part 1: Safety requirements, test methods91.220Gradbena opremaConstruction equipment13.340.60Protection against falling and slippingICS:Ta slovenski standard je istoveten z:EN 1263-1:2014SIST EN 1263-1:2015en,fr,de01-marec-2015SIST EN 1263-1:2015SLOVENSKI
STANDARDSIST EN 1263-1:20021DGRPHãþD

EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 1263-1
December 2014 ICS 13.340.60 Supersedes EN 1263-1:2002English Version
Temporary works equipment - Safety nets - Part 1: Safety requirements, test methods
Équipements temporaires de chantiers - Filets de sécurité -Partie 1 : Exigences de sécurité, méthodes d'essai
Temporäre Konstruktionen für Bauwerke - Schutznetze (Sicherheitsnetze) - Teil 1: Sicherheitstechnische Anforderungen, Prüfverfahren This European Standard was approved by CEN on 8 November 2014.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels © 2014 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1263-1:2014 ESIST EN 1263-1:2015

Prototype assessment . 39 Annex B (informative)
On-going production inspection . 40 B.1 On-going production inspection . 40 B.2 Annual inspection of test mesh . 41 Bibliography . 42
...