EN ISO 11297-1:2013

Plastics piping systems for renovation of underground drainage and sewerage networks under pressure - Part 1: General (ISO 11297-1:2013)

ISO 11297-1:2013 specifies the requirements and test methods for plastics piping systems intended to be used for the renovation of underground drainage and sewerage networks under pressure. It is applicable to pipes and fittings, as manufactured, as well as to the installed lining system. It is not applicable to cover sprayed coatings, the existing pipeline or any annular filler.
ISO 11297-1:2013 gives the general requirements common to all relevant renovation techniques.

Kunststoff-Rohrleitungssysteme für die Renovierung von erdverlegten Abwasserdruckleitungen - Teil 1: Allgemeines (ISO 11297-1:2013)

Dieser Teil der ISO 11297 legt Anforderungen und Prüfverfahren für Kunststoff-Rohrleitungssysteme fest, die für die Renovierung von erdverlegten Abwasserdruckleitungen vorgesehen sind. Er gilt sowohl für Rohre und Formstücke im 'M'-Zustand als auch für das eingebaute Lining-System. Er gilt nicht für aufgesprühte Beschichtungen, bestehende Rohrleitungen und Ringraumverfüllungen.
Dieser Teil der ISO 11297 enthält die allgemeinen Anforderungen, die für alle zutreffenden Renovierungs-techniken gelten.

Systèmes de canalisations en plastique pour la rénovation des réseaux de branchements et de collecteurs d'assainissement enterrés sous pression - Partie 1: Généralités (ISO 11297-1:2013)

L'ISO 11297-1:2013 spécifie les exigences et les méthodes d'essai des systèmes de canalisations en plastique destinés à être utilisés pour la rénovation des réseaux de branchements et de collecteurs d'assainissement enterrés sous pression. Elle s'applique aux tuyaux et raccords, tels que fabriqués, ainsi qu'au système de rénovation installé. Elle ne s'applique pas aux enduits projetés, à la canalisation existante ou à tout matériau de remplissage annulaire.
L'ISO 11297-1:2013 donne les exigences générales communes à toutes les techniques de rénovation pertinentes.

Cevni sistemi iz polimernih materialov za obnovo podzemnih omrežij za odvodnjavanje in kanalizacijo pod tlakom - 1. del: Splošno (ISO 11297-1:2013)

Ta del standarda ISO 11297 določa zahteve in preskusne metode za cevne sisteme iz polimernih materialov za uporabo pri obnovi podzemnih omrežij za odvodnjavanje in kanalizacijo pod tlakom. Uporablja se za cevi in fitinge, kot so izdelani, ter za nameščene sisteme cevi. Ne uporablja se za razpršene obloge, obstoječe cevovode ali kakršno koli obročasto polnilo. Ta del standarda ISO 11297 podaja splošne zahteve, ki so skupne vsem ustreznim tehnikam obnove.

General Information

• Status: Withdrawn
• Publication Date: 07-May-2013
• Withdrawal Date: 03-Apr-2018
• ICS: 23.040.20 - Plastics pipes
• ICS: 23.040.45 - Plastics fittings
• ICS: 23.060.01 - Valves in general
• ICS: 91.140.80 - Drainage systems
• ICS: 93.030 - External sewage systems
• Technical Committee: CEN/TC 155 - Plastics piping systems and ducting systems
• Drafting Committee: CEN/TC 155/WG 17 - Plastic components for the use of renovation of piping systems
• Current Stage: 9960 - Withdrawal effective - Withdrawal
• Completion Date: 04-Apr-2018
• Ref Project: SIST EN ISO 11297-1:2013 - Plastics piping systems for renovation of underground drainage and sewerage networks under pressure - Part 1: General (ISO 11297-1:2013)

Relations

• Replaced By: EN ISO 11297-1:2018 - Plastics piping systems for renovation of underground drainage and sewerage networks under pressure - Part 1: General (ISO 11297-1:2018)
• Effective Date: 08-Jun-2022

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 11297-1:2013
01-julij-2013
Cevni sistemi iz polimernih materialov za obnovo podzemnih omrežij za
odvodnjavanje in kanalizacijo pod tlakom - 1. del: Splošno (ISO 11297-1:2013)
Plastics piping systems for renovation of underground drainage and sewerage networks
under pressure - Part 1: General (ISO 11297-1:2013)
Kunststoff-Rohrleitungssysteme für die Renovierung von erdverlegten
Abwasserdruckleitungen - Teil 1: Allgemeines (ISO 11297-1:2013)
Systèmes de canalisations en plastique pour la rénovation des réseaux de
branchements et de collecteurs d'assainissement enterrés sous pression - Partie 1:
Généralités (ISO 11297-1:2013)
Ta slovenski standard je istoveten z: EN ISO 11297-1:2013
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
91.140.80 Drenažni sistemi Drainage systems
93.030 Zunanji sistemi za odpadno External sewage systems
vodo
SIST EN ISO 11297-1:2013 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 11297-1:2013

---------------------- Page: 2 ----------------------

SIST EN ISO 11297-1:2013


EUROPEAN STANDARD
EN ISO 11297-1

NORME EUROPÉENNE

EUROPÄISCHE NORM
May 2013
ICS 23.040.45; 23.040.20; 91.140.80; 93.030
English Version
Plastics piping systems for renovation of underground drainage
and sewerage networks under pressure - Part 1: General (ISO
11297-1:2013)
Systèmes de canalisations en plastique pour la rénovation Kunststoff-Rohrleitungssysteme für die Renovierung von
des réseaux de branchements et de collecteurs erdverlegten Abwasserdruckleitungen - Teil 1: Allgemeines
d'assainissement enterrés sous pression - Partie 1: (ISO 11297-1:2013)
Généralités (ISO 11297-1:2013)
This European Standard was approved by CEN on 18 April 2013.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member.

This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.





EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2013 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 11297-1:2013: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 11297-1:2013
EN ISO 11297-1:2013 (E)
Contents Page
Foreword .3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 11297-1:2013
EN ISO 11297-1:2013 (E)
Foreword
This document (EN ISO 11297-1:2013) has been prepared by Technical Committee ISO/TC 138 "Plastics
pipes, fittings and valves for the transport of fluids" in collaboration with Technical Committee CEN/TC 155
“Plastics piping systems and ducting systems” the secretariat of which is held by NEN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by November 2013, and conflicting national standards shall be withdrawn
at the latest by November 2013.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech
Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece,
Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom.
Endorseme
...