EN 1999-1-1:2007
(Main)Eurocode 9: Design of aluminium structures - Part 1-1: General structural rules
Eurocode 9: Design of aluminium structures - Part 1-1: General structural rules
(1) EN 1999-1-1 gives basic design rules for structures made of wrought aluminium alloys and limited guidance for cast alloys (see section 3).
NOTE Minimum material thickness may be defined in the National Annex. The following limits are recommended – if not otherwise explicitly stated in this standard:
- components with material thickness not less than 0,6 mm;
- welded components with material thickness not less than 1,5 mm;
- connections with:
o steel bolts and pins with diameter not less than 5 mm;
o aluminium bolts and pins with diameter not less than 8 mm;
o rivets and thread forming screws with diameter not less than 4,2 mm
(2) The following subjects are dealt with in EN 1999-1-1:
Section 1: General
Section 2: Basis of design
Section 3: Materials
Section 4: Durability
Section 5: Structural analysis
Section 6: Ultimate limit states for members
Section 7: Serviceability limit states
Section 8: Design of joints
Annex A Execution classes
Annex B Equivalent T-stub in tension
Annex C Materials selection
Annex D Corrosion and surface protection
Annex E Analytical models for stress strain relationship
Annex F Behaviour of cross section beyond elastic limit
Annex G Rotation capacity
Annex H Plastic hinge method for continuous beams
Annex I Lateral torsional buckling of beams and torsional or flexural-torsional buckling of compression members
Annex J Properties of cross sections
Annex K Shear lag effects in member design
Annex L Classification of connections
Annex M Adhesive bonded connections
(3) Sections 1 to 2 provide additional clauses to those given in EN 1990 “Basis of structural design”.
(4) Section 3 deals with material properties of products made of structural aluminium alloys.
(5) Section 4 gives general rules for durability.
(6) Section 5 refers to the structural analysis of structures, in which the members can be modelled with sufficient accuracy as line elements for global analysis.
(7) Section 6 g
Eurocode 9: Bemessung und Konstruktion von Aluminiumtragwerken - Teil 1-1: Allgemeine Bemessungsregeln
1.1.1 Anwendungsbereich von EN 1999
(1)P EN 1999 gilt für den Entwurf, die Berechnung und die Bemessung von Bauwerken und Tragwerken aus Aluminium. Sie entspricht den Grundsätzen und Anforderungen an die Tragfähigkeit und Gebrauchs¬tauglichkeit von Tragwerken, sowie den Grundlagen für ihre Bemessung und Nachweise, die in EN 1990 Grundlagen der Tragwerksplanung enthalten sind.
(2) EN 1999 behandelt ausschließlich Anforderungen an die Tragfähigkeit, die Gebrauchstauglichkeit, die Dauerhaftigkeit und den Feuerwiderstand von Tragwerken aus Aluminium. Andere Anforderungen, wie z. B. Wärmeschutz oder Schallschutz, werden nicht behandelt.
(3) EN 1999 gilt in Verbindung mit folgenden Regelwerken:
EN 1990 Grundlagen der Tragwerksplanung
EN 1991 Einwirkungen auf Tragwerke
Europäische Normen für Bauprodukte, die für Aluminiumtragwerke Verwendung finden
prEN 1090-1: Ausführung von Stahltragwerken und Aluminiumtragwerken Teil 1: Konformitäts¬nachweis für tragende Bauteile )
prEN 1090-3: Ausführung von Stahltragwerken und Aluminiumtragwerken Teil 3: Technische Anforderungen für Aluminiumtragwerke5)
(4) EN 1999 ist in fünf Teile gegliedert:
EN 1999-1-1 Bemessung und Konstruktion von Aluminiumtragwerken: Allgemeine Bemessungsregeln.
EN 1999-1-2 Bemessung und Konstruktion von Aluminiumtragwerken: Tragwerksbemessung für den Brandfall
EN 1999-1-3 Bemessung und Konstruktion von Aluminiumtragwerken: Ermüdungsbeanspruchte Tragwerke
EN 1999-1-4 Bemessung und Konstruktion von Aluminiumtragwerken: Kaltgeformte Profiltafeln
EN 1999-1-5 Bemessung und Konstruktion von Aluminiumtragwerken: Schalentragwerke
Eurocode 9: Calcul des structures en aluminium - Partie 1-1: Règles générales
(1) L'EN 1999-1-1 donne les règles fondamentales de calcul des structures en alliage d'aluminium corroyé et des recommandations limitées pour les alliages de fonderie (voir la section 3).
NOTE L'épaisseur minimale du matériau peut être définie dans l'Annexe Nationale. Les limites ci-dessous sont recommandées – si elles ne sont pas explicitement établies dans la présente norme :
- - composants d'épaisseur supérieure ou égale à 0,6 mm ;
- - composants soudés d'épaisseur supérieure ou égale à 1,5 mm ;
- - liaisons à l'aide de :
· boulons et goupilles en acier de diamètre supérieur ou égal à 5 mm ;
· boulons et goupilles en aluminium de diamètre supérieur ou égal à 8 mm ;
· rivets et vis taraudeuses de diamètre supérieur ou égal à 4,2 mm.
(2) Les sujets ci-dessous sont traités dans l'EN 1999 1-1 :
Section 1 : Généralités
Section 2 : Base de calcul
Section 3 : Matériaux
Section 4 : Durabilité
Section 5 : Analyse structurale
Section 6 : Etats limites ultimes des barres
Section 7 : Etats limites de service
Section 8 : Calcul des assemblages
Annexe A Classes d'exécution
Annexe B Bout en T équivalent en tension
Annexe C Sélection des matériaux
Annexe D Corrosion et protection des surfaces
Annexe E Modèles analytiques pour le rapport contrainte-déformation
Annexe F Comportement de la section transversale au-delà de la limite d'élasticité
Annexe G Capacité de rotation
Annexe H Méthode d'analyse des rotules plastiques pour poutres continues
Annexe I Déversement des poutres et flambement par torsion et torsion-flexion des barres en compression
Annexe J Propriétés des sections transversales
Annexe K Effets de traînage de cisaillement dans le calcul des barres
Annexe L Classification des liaisons
Annexe M Liaisons collées par adhésif
(3) Les Sections 1 à 2 donnent des articles supplémentaires à ceux indiqués dans l’EN 1990 “Base du calcul des structures”.
Evrokod 9: Projektiranje konstrukcij iz aluminijevih zlitin - 1-1. del: Splošna pravila za konstrukcije
Standard EN 1999 se uporablja za projektiranje stavb ter inženirskih in konstrukcijskih objektov iz aluminija. Upošteva načela in zahteve glede varnosti in uporabnosti konstrukcij ter podlago za njihovo projektiranje in preverjanje, ki so podane v standardu EN 1990 – Osnove projektiranja. Standard EN 1999 se nanaša le na zahteve za odpornost, uporabnost, trajnost in požarno odpornost aluminijastih konstrukcij. Ostale zahteve, na primer glede toplotne in zvočne izolativnosti, niso obravnavane. Standard EN 1999 je namenjen za uporabo v povezavi z naslednjimi standardi: – EN 1990 »Osnove projektiranja« – EN 1991 »Vplivi na konstrukcije« – Evropski standardi za konstrukcijske izdelke v zvezi z aluminijastimi konstrukcijami – prEN 1090-1: Izvedba jeklenih konstrukcij in aluminijastih konstrukcij – 1. del: Zahteve za ugotavljanje skladnosti sestavnih delov konstrukcij5 – prEN 1090-3: Izvedba jeklenih konstrukcij in aluminijastih konstrukcij – 3. del: Tehnične zahteve za aluminijaste konstrukcije5 EN 1999 je razdeljen na pet delov: EN 1999-1-1 Projektiranje konstrukcij iz aluminijevih zlitin: Splošna pravila za konstrukcije. EN 1999-1-2 Projektiranje konstrukcij iz aluminijevih zlitin: Projektiranje požarnovarnih konstrukcij. EN 1999-1-3 Projektiranje konstrukcij iz aluminijevih zlitin: Konstrukcije, občutljive na utrujanje. EN 1999-1-4 Projektiranje konstrukcij iz aluminijevih zlitin: Hladno oblikovane konstrukcijske pločevine. EN 1999-1-5 Projektiranje konstrukcij iz aluminijevih zlitin: Lupinaste konstrukcije.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Eurocode 9 - Design of aluminium structures - Part 1-1: General structural rulesEvrokod 9: Projektiranje konstrukcij iz aluminijevih zlitin - 1-1. del: Splošna pravila za konstrukcijeEurocode 9 - Calcul des structures en aluminium - Partie 1-1: Regles généralesEurocode 9 - Bemessung und Konstruktion von Aluminiumtragwerken - Teil 1-1: Allgemeine BemessungsregelnTa slovenski standard je istoveten z:EN 1999-1-1:2007SIST EN 1999-1-1:2007en;fr;de91.080.10Kovinske konstrukcijeMetal structures91.010.30Technical aspectsICS:SIST ENV 1999-1-1:20021DGRPHãþDSLOVENSKI
STANDARDSIST EN 1999-1-1:200701-maj-2007
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 1999-1-1February 2007ICS 91.010.30; 91.080.10Supersedes ENV 1999-1-1:1998
English VersionEurocode 9 - Design of aluminium structures - Part 1-1: Generalstructural rulesEurocode 9 - Calcul des structures en aluminium - Partie 1-1: Règles généralesEurocode 9 - Bemessung und Konstruktion vonAluminiumtragwerken - Teil 1-1: AllgemeineBemessungsregelnThis European Standard was approved by CEN on 18 September 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2007 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 1999-1-1:2007: E
EN 1999-1-1: 2007 (E)
2 Content Page Foreword.7 1 General.11 1.1 Scope.11 1.1.1 Scope of EN 1999.11 1.1.2 Scope of EN 1999-1-1.11 1.2 Normative references.12 1.2.1 General references.12 1.2.2 References on structural design.12 1.2.3 References on aluminium alloys.13 1.2.4 References on welding.15 1.2.5 Other references.15 1.3 Assumptions.16 1.4 Distinction between principles and application rules.16 1.5 Terms and definitions.16 1.6 Symbols.17 1.7 Conventions for member axes.27 1.8 Specification for execution of the work.27 2 Basis of design.29 2.1 Requirements.29 2.1.1 Basic requirements.29 2.1.2 Reliability management.29 2.1.3 Design working life, durability and robustness.29 2.2 Principles of limit state design.29 2.3 Basic variables.30 2.3.1 Actions and environmental influences.30 2.3.2 Material and product properties.30 2.4 Verification by the partial factor method.30 2.4.1 Design value of material properties.30 2.4.2 Design value of geometrical data.30 2.4.3 Design resistances.30 2.4.4 Verification of static equilibrium (EQU).31 2.5 Design assisted by testing.31 3 Materials.32 3.1 General.32 3.2 Structural aluminium.32 3.2.1 Range of materials.32 3.2.2 Material properties for wrought aluminium alloys.33 3.2.3 Material properties for cast aluminium alloys.36 3.2.4 Dimensions, mass and tolerances.37 3.2.5 Design values of material constants.37 3.3 Connecting devices.38 3.3.1 General.38 3.3.2 Bolts, nuts and washers.38 3.3.3 Rivets.39 3.3.4 Welding consumables.40 3.3.5 Adhesives.42 4 Durability.42 5 Structural analysis.43 5.1 Structural modelling for analysis.43 5.1.1 Structural modelling and basic assumptions.43 5.1.2 Joint modelling.43 5.1.3 Ground-structure interaction.43 5.2 Global analysis.43
EN 1999-1-1: 2007 (E)
3 5.2.1 Effects of deformed geometry of the structure.43 5.2.2 Structural stability of frames.44 5.3 Imperfections.45 5.3.1 Basis.45 5.3.2 Imperfections for global analysis of frames.45 5.3.3 Imperfection for analysis of bracing systems.49 5.3.4 Member imperfections.52 5.4 Methods of analysis.52 5.4.1 General.52 5.4.2 Elastic global analysis.52 5.4.3 Plastic global analysis.52 6 Ultimate limit states for members.53 6.1 Basis.53 6.1.1 General.53 6.1.2 Characteristic value of strength.53 6.1.3 Partial safety factors.53 6.1.4 Classification of cross-sections.53 6.1.5 Local buckling resistance.58 6.1.6 HAZ softening adjacent to welds.59 6.2 Resistance of cross-sections.61 6.2.1 General.61 6.2.2 Section properties.62 6.2.3 Tension.63 6.2.4 Compression.64 6.2.5 Bending moment.64 6.2.6 Shear.66 6.2.7 Torsion.67 6.2.8 Bending and shear.69 6.2.9 Bending and axial force.69 6.2.10 Bending, shear and axial force.70 6.2.11 Web bearing.71 6.3 Buckling resistance of members.71 6.3.1 Members in compression.71 6.3.2 Members in bending.75 6.3.3 Members in bending and axial compression.
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.