EN 60335-2-89:2010/A1:2016

Household and similar electrical appliances - Safety - Part 2-89: Particular requirements for commercial refrigerating appliances with an incorporated or remote refrigerant condensing unit or compressor

Sicherheit elektrischer Geräte für den Hausgebrauch und ähnliche Zwecke - Teil 2-89: Besondere Anforderungen für gewerbliche Kühl-/Gefriergeräte mit eingebautem oder getrenntem Verflüssigersatz oder Motorverdichter

Appareils électrodomestiques et analogues - Sécurité - Partie 2-89: Règles particulières pour les appareils de réfrigération à usage commercial avec une unité de condensation du fluide frigorigène ou un compresseur incorporés ou à distance

Gospodinjski in podobni električni aparati - Varnost - 2-89. del: Posebne zahteve za komercialne hladilne naprave z vgrajeno ali zunanjo hladilno kondenzatorsko enoto ali kompresorjem - Dopolnilo A1

General Information

• Status: Published
• Publication Date: 11-Feb-2016
• Withdrawal Date: 11-Feb-2019
• ICS: 97.130.20 - Commercial refrigerating appliances
• Technical Committee: CLC/TC 61 - Safety of household and similar electrical appliances
• Drafting Committee: IEC/SC 61C - IEC_SC_61C
• Current Stage: 6060 - Document made available - Publishing
• Start Date: 12-Feb-2016
• Completion Date: 12-Feb-2016
• Directive: 2006/42/EC - Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast)
• Mandate: M/396 - Mandate to CEN and Cenelec for standardisation in the field of machinery
• Ref Project: SIST EN 60335-2-89:2011/A1:2016 - Household and similar electrical appliances - Safety - Part 2-89: Particular requirements for commercial refrigerating appliances with an incorporated or remote refrigerant condensing unit or compressor

Relations

• Replaced By: EN IEC 60335-2-89:2022 - Household and similar electrical appliances - Safety - Part 2-89: Particular requirements for commercial refrigerating appliances and ice-makers with an incorporated or remote refrigerant unit or motor-compressor
• Effective Date: 23-Jan-2023
• Amends: EN 60335-2-89:2010 - Household and similar electrical appliances - Safety - Part 2-89: Particular requirements for commercial refrigerating appliances with an incorporated or remote refrigerant condensing unit or compressor
• Effective Date: 28-Jan-2023

Standards Content (Sample)

SLOVENSKI STANDARD
01-april-2016
*RVSRGLQMVNLLQSRGREQLHOHNWULþQLDSDUDWL9DUQRVWGHO3RVHEQH]DKWHYH
]DNRPHUFLDOQHKODGLOQHQDSUDYH]YJUDMHQRDOL]XQDQMRKODGLOQRNRQGHQ]DWRUVNR
HQRWRDOLNRPSUHVRUMHP'RSROQLOR$
Household and similar electrical appliances - Safety - Part 2-89: Particular requirements
for commercial refrigerating appliances with an incorporated or remote refrigerant
condensing unit or compressor
Sicherheit elektrischer Geräte für den Hausgebrauch und ähnliche Zwecke - Teil 2-89:
Besondere Anforderungen für gewerbliche Kühl-/Gefriergeräte mit eingebautem oder
getrenntem Verflüssigersatz oder Motorverdicht
Appareils électrodomestiques et analogues - Sécurité - Partie 2-89: Règles particulières
pour les appareils de réfrigération à usage commercial avec une unité de condensation
du fluide frigorigène ou un compresseur incorporés ou à distance
Ta slovenski standard je istoveten z: EN 60335-2-89:2010/A1:2016
ICS:
97.130.20 Hladilne naprave za trgovine Commercial refrigerating
appliances
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN 60335-2-89:2010/A1

NORME EUROPÉENNE
EUROPÄISCHE NORM
February 2016
ICS 97.130.20
English Version
Household and similar electrical appliances - Safety -
Part 2-89: Particular requirements for commercial refrigerating
appliances with an incorporated or remote refrigerant
condensing unit or compressor
(IEC 60335-2-89:2010/A1:2012 , modified)
Appareils électrodomestiques et analogues - Sécurité - Sicherheit elektrischer Geräte für den Hausgebrauch und
Partie 2-89: Règles particulières pour les appareils de ähnliche Zwecke - Teil 2-89: Besondere Anforderungen für
réfrigération à usage commercial avec une unité de gewerbliche Kühl-/Gefriergeräte mit eingebautem oder
condensation du fluide frigorigène ou un compresseur getrenntem Verflüssigersatz oder Motorverdichter
incorporés ou à distance (IEC 60335-2-89:2010/A1:2012 , modifiziert)
(IEC 60335-2-89:2010/A1:2012 , modifiée)
This amendment A1 modifies the European Standard EN 60335-2-89:2010; it was approved by CENELEC on 2015-08-17. CENELEC
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this amendment the
status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation under the
responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the same status as
the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2016 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 60335-2-89:2010/A1:2016 E

European foreword
This document (EN 60335-2-89:2010/A1:2016) consists of the text of IEC 60335-2-89:2010/A1:2012 prepared
by SC 61C "Safety of refrigeration appliances for household and commercial use" of IEC/TC 61 "Safety of
household and similar electrical appliances", together with the common modifications prepared by CLC/TC 61,
"Safety of household and similar electrical appliances".

The following dates are fixed:

(dop) 2016-08-12
• latest date by which the document has to be
implemented at national level
by publication of an identical
national standard or by endorsement
(dow) 2019-02-12
• latest date by which the national standards conflicting
with the document have to be withdrawn

Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such patent rights.

This amendment supplements or modifies the corresponding clauses of EN 60335-1:2012 and
EN 60335-2-89:2010.
Clauses, subclauses, notes, tables and annexes which are additional to those in IEC 60335-2-89:2010/A1:2012
or in IEC 60335-1:2010 are prefixed “Z”.

This document has been prepared under a mandate given to CENELEC by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive.

For the relationship with EU Directive 2006/42/EC, see informative Annex ZZ, which is an integral part of this
document.
Endorsement notice
The text of the International Standard IEC 60335-2-89:2010/A1:2012 was approved by CENELEC as a
European Standard with agreed common modifications.

COMMON MODIFICATIONS
Introduction
Replace the addition of CENELEC common modifications with the following:
The Essential Health and Safety Requirements of the Machinery Directive 2006/42/EC have also been taken
into account.
Products within the scope of this standard may incorporate pressurized components for which the Pressure
Equipment Directive, 2014/68/EU, applies:
Refrigerating systems having a pressure greater than 0,05 MPa are considered to be assemblies falling within
the scope of the Pressure Equipment Directive, 2014/68/EU. However, according to Article 1, item 2 (f) of the
Directive, equipment classified no higher than category I under Article 13 of the PED and covered by the Low
Voltage Directive or Machinery Directive are excluded from its scope.

Compliance with this standard does not give a means of conformity with the essential requirements of the
Pressure Equipment Directive for those appliances that fall within its scope.

Other requirements and other EU Directives may be applicable to the appliances falling within the scope of this
standard.
1 Scope
st
Add after the 1 paragraph the following new paragraph:
This standard applies to commercial refrigerators and freezers used for the display of food products, including
beverages, for retail sale.
Add the following NOTE after NOTE 101:
NOTE Z101 Commercial use of these refrigerating appliances is for example their use in restaurants, canteens,
hospitals and commercial enterprises such as bakeries, butcheries, supermarkets etc.
Add the following paragraph before NOTE 102:
In many countries additional requirements on the safe use of the equipment covered may be specified by the
national health authorities, the national authorities responsible for the protection of labour, the national water
supply authorities and similar authorities.
NOTE 102:
Delete the second dashed item:
Add the following dashed item:
– for scrapping of appliances, additional requirements may be necessary.

NOTE 103
Add the following new dashed item:
– appliances with a charge greater than 150 g of flammable refrigerant in each separate refrigerant circuit.

NOTE 104: Delete the NOTE.
Add the following new paragraph:
Products covered by this standard do not create a noise hazard; therefore no specific provisions concerning
noise are given.
2 Normative references
Add the following standards:
EN 614-1:2006+A1:2009, Safety of machinery – Ergonomic design principles – Part 1: Terminology and general
principles
EN 614-2:2000+A1:2008, Safety of machinery - Ergonomic design principles - Part 2: Interactions between the
design of machinery and work tasks
EN ISO 14159:2008, Safety of machinery - Hygiene requirements for the design of machinery (ISO 14159:2002)

3 Terms and Definitions
Add the following definitions:
3.Z101
guard
part of the appliance specifically designed to provide protection by means of a physical barrier
3.Z102
operator
person installing, operating, adjusting, maintaining, cleaning or moving the appliance
3.Z103
commercial use
intended use of appliances covered by this standard in a professional way
Note 1 to entry: For the purpose of this standard commercial use may be read as not intended for domestic use.
4 General requirement
Replacement:
Appliances shall be constructed so that they function safely so as to cause no danger to persons or
surroundings during normal use, even in the event of carelessness, and during installation, adjusting,
maintenance, cleaning, repairing or transportation.
The use of flammable refrigerants involves some additional hazards which are not associated with appliances which use
non-flammable refrigerants.
This standard addresses the hazard due to ignition of leaked flammable refrigerant by potential ignition sources associated
with the appliance.
The hazard due to ignition of leaked flammable refrigerant by an external potential ignition source associated with the
environment in which the appliance is installed is compensated for by the low probability of ignition.
In general, this principle is achieved by fulfiling the relevant requirements specified in this standard and compliance is
checked by carrying out all the relevant tests.
The interpretations included in CLC/TR 50417 shall be taken into consideration together with the relevant requirements in
the standards listed therein.
7 Marking and instructions
7.1 Replace the fourth and fifth dashed items in part 1 by:

- business name and full address of the manufacturer and, where applicable, his authorized representative;
- model or type reference, serial number, if any, and production year;

NOTE Z101  Production year is the year when the production process is completed. The production year can be a part of the serial number.

Add a new dashed item:
- designation of the appliance.

NOTE Z102  The designation may be a combination of letters and/or numbers and shall enable to identify the machine as specified in the
instructions.
7.12 Add the following to the addition:
The instructions shall contain the following:
- business name and full address of the manufacturer and, where applicable, his authorized representative;
- model or type reference of the appliance as marked on the appliance itself, except for the serial number;
- designation of the appliance together with its explanation in case it is given by a combination of letters
and/or numbers;
- a general description of the appliance, when needed due to the complexity of the appliance;
- specific precautions if required during installation, operation, adjusting, user maintenance, cleaning,
repairing or moving;
- when needed drawings, diagrams, descriptions and explanations necessary for the safe use and user
maintenance of the appliance;
- the possible reasonably foreseeable misuse and, whenever relevant, a warning against the effects it may
have on the safe use of the appliance;
The words “Original instructions” shall appear on the language version(s) verified by the manufacturer or by the
authorized representative.
When a translation of the original instructions has been provided by a person introducing the appliance on the
market; the meaning of the sentence “Translation of the original instructions” has to appear in the relevant
instructions delivered with the appliance.
The instructions for maintenance/service to be done by specialized personnel, mandated by the manufacturer or
the authorized representative may be supplied in only one Community language which the specialized
personnel understand.
The instructions shall indicate the type and frequency of inspections and maintenance required for safe
operation including the preventive maintenance measures.
Add the new following sub-clauses:
7.12.Z101 Information shall be given:
– on use, transportation, assembly, dismantling when out of service, testing or foreseeable breakdowns, if
these operations have consequences on stability of the appliance in order to avoid overturning, falling or
uncontrolled movements of the appliance or of its component parts;
– on how to maintain adequate mechanical stability when in use, during transportation, assembly,
dismantling, scrapping and any other action involving the appliance;
– on the protective measures to be taken by the user, including, where appropriate, the personal
protective equipment to be provided;
– on the operating method to be followed in the event of accident or breakdown; if a blockage is likely to
occur the operating method to safely unblock the appliance;
– on the specifications on the spare parts to be used, when these affect the health and safety of the
operator;
– that the A-weighted emission sound pressure level is below 70 dB(A);
7.12.1.Z102 Instructions shall be given, when necessary, concerning safe handling and transportation on
the packed appliance or have to be delivered together with the package.
7.12.1.Z103 If the installation instructions state that appliance can be placed on top of a other appliance,
they shall state which appliances are suitable. Instructions shall be given for the assembly of the appliances.
The instructions shall state how to obtain any fixing attachments required, unless they are supplied with the
appliance.
7.12.Z104 The instructions shall include a warning that the appliance shall be disconnected from its power
source during cleaning or maintenance and when replacing parts. If the removal of the plug is foreseen, it shall
be clearly indicated that the removal of the plug has to be such that an operator can check from any of the
points to which he has access that the plug remains removed.
If this is not possible, due to the construction
...