Petroleum and related products - Determination of the flammability characteristics of fluids in contact with hot surfaces - Manifold ignition test (ISO 20823:2003)

This International Standard specifies a method to determine the relative flammability of fluids when contacted with a hot metal surface
at a fixed temperature, but it is also possible to gauge fluid ignition temperatures by adjustment of mainfold temperature. The primary use is to assess the resistance to ignition of fire-resistant hydraulic fluids which are, by definition, difficult to ignite. The use of this International Standard with other types of more flammable fluids will significantly increase the hazards of this procedure. This procedure is specified in ISO 12922 as an indicator of fire-resistance.

Mineralölerzeugnisse und verwandte Produkte - Bestimmung der Entflammbarkeits-Charakteristik von Flüssigkeiten bei Kontakt mit heißen Oberflächen - Zündverfahren (ISO 20823:2003)

Diese Internationale Norm beschreibt ein Prüfverfahren zur Bestimmung der relativen Entflammbarkeit von Flüssigkeiten beim Auftreffen auf heiße, metallische Oberflächen bei einer fest eingestellten Temperatur. Durch Anpassung der Oberflächentemperatur besteht ebenfalls die Möglichkeit, die Zündtemperatur von Flüssigkeiten anzuzeigen.
Die Hauptanwendung besteht in der Bewertung der Zündhemmung schwerentflammbarer Druckflüssigkeiten, welche durch Definition schwer entzündbar sind.
Diese Norm kann auch für andere Typen entflammbarer Flüssigkeiten bei niedrigeren Oberflächentemperaturen angewendet werden. Dabei ist jedoch mit einem deutlich zunehmenden Anstieg der Brandgefahr während der Prüfung zu rechnen.
ANMERKUNG   Dieses Prüfverfahren ist in ISO 12922:1999, Lubricants, industrial oils and related products (class L) - Family H (Hydraulic systems) - Specifications for categories HFAE, HFAS, HFB, HFC, HFDR and HFDU als Prüfung der Schwerentflammbarkeit vorgeschrieben

Pétrole et produits connexes - Détermination des caractéristiques d'inflammabilité de fluides au contact de surfaces chaudes - Essai d'inflammation sur métal chaud (ISO 20823:2003)

L'ISO 20823:2003 spécifie une méthode d'essai qui a pour but de déterminer les caractéristiques d'inflammabilité relative des fluides quand ils sont mis au contact d'une surface métallique chaude à une température définie, mais il est également possible d'évaluer la température d'inflammation d'un fluide en ajustant la température du métal.
Elle est particulièrement utilisée pour évaluer la résistance à l'inflammation des fluides hydrauliques difficilement inflammables, qui sont par définition difficiles à enflammer.
Elle peut être utilisée avec d'autres types de fluides plus inflammables à des températures de surface inférieures, mais ceci peut accroître considérablement les risques liés à la méthode.

Nafta in naftni proizvodi – Določanje lastnosti gorljivosti tekočin v stiku z vročimi površinami – Preskus vžiganja (ISO 20823:2003)

General Information

Status
Published
Publication Date
31-Oct-2003
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
01-Nov-2003
Due Date
01-Nov-2003
Completion Date
01-Nov-2003

Buy Standard

Standard
EN ISO 20823:2003
English language
8 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST EN ISO 20823:2003
01-november-2003
1DIWDLQQDIWQLSURL]YRGL±'RORþDQMHODVWQRVWLJRUOMLYRVWLWHNRþLQYVWLNX]YURþLPL
SRYUãLQDPL±3UHVNXVYåLJDQMD ,62
Petroleum and related products - Determination of the flammability characteristics of
fluids in contact with hot surfaces - Manifold ignition test (ISO 20823:2003)
Mineralölerzeugnisse und verwandte Produkte - Bestimmung der Entflammbarkeits-
Charakteristik von Flüssigkeiten bei Kontakt mit heißen Oberflächen - Zündverfahren
(ISO 20823:2003)
Pétrole et produits connexes - Détermination des caractéristiques d'inflammabilité de
fluides au contact de surfaces chaudes - Essai d'inflammation sur métal chaud (ISO
20823:2003)
Ta slovenski standard je istoveten z: EN ISO 20823:2003
ICS:
13.220.40 Sposobnost vžiga in Ignitability and burning
obnašanje materialov in behaviour of materials and
proizvodov pri gorenju products
75.080 Naftni proizvodi na splošno Petroleum products in
general
SIST EN ISO 20823:2003 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 20823:2003

---------------------- Page: 2 ----------------------

SIST EN ISO 20823:2003

---------------------- Page: 3 ----------------------

SIST EN ISO 20823:2003

---------------------- Page: 4 ----------------------

SIST EN ISO 20823:2003

---------------------- Page: 5 ----------------------

SIST EN ISO 20823:2003

---------------------- Page: 6 ----------------------

SIST EN ISO 20823:2003


INTERNATIONAL ISO
STANDARD 20823
First edition
2003-08-01


Petroleum and related products —
Determination of the flammability
characteristics of fluids in contact with
hot surfaces — Manifold ignition test
Pétrole et produits connexes — Détermination des caractéristiques
d'inflammabilité de fluides au contact de surfaces chaudes — Essai
d'inflammation sur métal chaud




Reference number
ISO 20823:2003(E)
©
ISO 2003

---------------------- Page: 7 ----------------------

SIST EN ISO 20823:2003
ISO 20823:2003(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2003
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2003 — All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 20823:2003
ISO 20823:2003(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 20823 was prepared by Technical Committee ISO/TC 28, Petroleum products and lubricants.
© ISO 2003 — All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 20823:2003

---------------------- Page: 10 ----------------------

SIST EN ISO 20823:2003
INTERNATIONAL STANDARD ISO 20823:2003(E)

Petroleum and related products — Determination of the
flammability characteristics of fluids in contact with hot
surfaces — Manifold ignition test
WARNING — The use of this International Standard may involve hazardous materials, operations and
equipment. This International Standard does not purport to address all of the safety problems
associated with its use. It is the responsibility of the user of this International Standard to establish
appropriate safety and health practices and determine the applicability of regulatory limitations prior
to use.
1 Scope
This International Standard specifies a test method to determine the relative flammability of fluids when
contacted with a hot metal surface at a fixed temperature, but it is also possible to gauge fluid ignition
temperatures by adjustment of the manifold temperature.
It is primarily used to assess the resistance to ignition of fire-resistant hydraulic fluids which are, by definition,
difficult to ignite.
It may be used with other types of more flammable fluids at lower surface temperatures, but this could
significantly increase the hazards of this procedure.
NOTE The procedure given in this International Standard is specified in ISO 12922:1999, Lubricants, industrial oils
and related products (class L) — Family H (Hydraulic systems) — Specifications for categories HFAE, HFAS, HFB, HFC,
HFDR and HFDU.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
1)
ISO 3170:— , Petroleum liquids — Manual sampling
3 Principle
A 10 ml test portion of fluid is dropped from a predetermined height and at a specified rate, onto a tube heated
to 700 °C, or another temperature in a series. The resulting spray is examined for flash or burn, both on the
tube and after dripping from the tube.

1)
To be published. (Revision of ISO 3170:1988)
© ISO 2003 — All rights reserved 1

---------------------- Page: 11 ----------------------

SIST EN ISO 20823:2003
ISO 20823:2003(E)
4 Reagents and materials
4.1 Steel wool
4.2 Absorbent cotton (cotton wool)
4.3 Cleaning solvent: any suitable light hydrocarbon solvent for wiping the tube.
NOTE 2,2,4-trimethylpentane, heptane or petroleum spirit boiling between 60 °C and 80 °C are suitable.
5 Apparatus
5.1 Simulated manifold test rig
5.1.1 General
The rig consists of a heated simulated manifold supported in a box frame, and is illustrated in Figure 1. It shall
be located in a fire-resistant enclosure with adequate ventilation to remove toxic and/or noxious combustion or
decomposition products.
5.1.2 Manifo
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.