SIST-TP CLC IEC/TR 63216:2020
(Main)Low-voltage switchgear and controlgear - Electromagnetic compatibility assessment for switchgear and controlgear and their assemblies (IEC/TR 63216:2019)
Low-voltage switchgear and controlgear - Electromagnetic compatibility assessment for switchgear and controlgear and their assemblies (IEC/TR 63216:2019)
The purpose of this document is to define homogeneous categories for the electromagnetic environments in order to harmonize as far as practicable all general rules and product standard requirements of electromagnetic compatibility (EMC), applicable to low-voltage switchgear, controlgear and their assemblies with built-in electronic circuits.
Niederspannungsschaltgeräte - Bewertung der elektromagnetischen Verträglichkeit von Schaltgeräten und deren Schaltgerätekombinationen (IEC/TR 63216:2019)
Appareillage à basse tension – Evaluation de la compatibilité électromagnétique des appareillages et ensembles d’appareillages à basse tension (IEC/TR 63216:2019)
Nizkonapetostne stikalne in krmilne naprave - Ocena elektromagnetne združljivosti za stikalne in krmilne naprave ter njihove sklope (IEC/TR 63216:2019)
General Information
Standards Content (Sample)
SLOVENSKI STANDARD
SIST-TP CLC IEC/TR 63216:2020
01-november-2020
Nizkonapetostne stikalne in krmilne naprave - Ocena elektromagnetne
združljivosti za stikalne in krmilne naprave ter njihove sklope (IEC/TR 63216:2019)
Low-voltage switchgear and controlgear - Electromagnetic compatibility assessment for
switchgear and controlgear and their assemblies (IEC/TR 63216:2019)
Niederspannungsschaltgeräte - Bewertung der elektromagnetischen Verträglichkeit von
Schaltgeräten und deren Schaltgerätekombinationen (IEC/TR 63216:2019)
Appareillage à basse tension – Evaluation de la compatibilité électromagnétique des
appareillages et ensembles d’appareillages à basse tension (IEC/TR 63216:2019)
Ta slovenski standard je istoveten z: CLC/IEC TR 63216:2020
ICS:
29.130.20 Nizkonapetostne stikalne in Low voltage switchgear and
krmilne naprave controlgear
33.100.01 Elektromagnetna združljivost Electromagnetic compatibility
na splošno in general
SIST-TP CLC IEC/TR 63216:2020 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST-TP CLC IEC/TR 63216:2020
---------------------- Page: 2 ----------------------
SIST-TP CLC IEC/TR 63216:2020
TECHNICAL REPORT CLC/IEC TR 63216
RAPPORT TECHNIQUE
TECHNISCHER BERICHT
August 2020
ICS 29.130.20
English Version
Low-voltage switchgear and controlgear - Electromagnetic
compatibility assessment for switchgear and controlgear and
their assemblies
(IEC/TR 63216:2019)
Appareillage à basse tension - Evaluation de la Niederspannungsschaltgeräte - Bewertung der
compatibilité électromagnétique des appareillages et elektromagnetischen Verträglichkeit von Schaltgeräten und
ensembles d'appareillages à basse tension deren Schaltgerätekombinationen
(IEC/TR 63216:2019) (IEC/TR 63216:2019)
This Technical Report was approved by CENELEC on 2020-08-10.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2020 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. CLC/IEC TR 63216:2020 E
---------------------- Page: 3 ----------------------
SIST-TP CLC IEC/TR 63216:2020
CLC/IEC TR 63216:2020 (E)
European foreword
This document (CLC/IEC TR 63216:2020) consists of the text of IEC/TR 63216:2019 prepared by
SC 121A "Low-voltage switchgear and controlgear" of IEC/TC 121 "Switchgear and controlgear and
their assemblies for low voltage".
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Endorsement notice
The text of the International Technical Report IEC/TR 63216:2019 was approved by CENELEC as a
European Technical Report without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60038 NOTE Harmonized as EN 60038
IEC 60364-5-52 NOTE Harmonized as HD 60364-5-52
IEC 60947 (series) NOTE Harmonized as EN IEC 60947 (series)
IEC 61000 (series) NOTE Harmonized as EN 61000 (series)
IEC 61000-2-2 NOTE Harmonized as EN 61000-2-2
IEC 61000-2-12 NOTE Harmonized as EN 61000-2-12
IEC 61000-4-9 NOTE Harmonized as EN 61000-4-9
IEC 61000-4-10 NOTE Harmonized as EN 61000-4-10
IEC 61000-4-12 NOTE Harmonized as EN 61000-4-12
IEC 61000-4-14 NOTE Harmonized as EN 61000-4-14
IEC 61000-4-20 NOTE Harmonized as EN 61000-4-20
IEC 61000-4-21 NOTE Harmonized as EN 61000-4-21
IEC 61000-4-27 NOTE Harmonized as EN 61000-4-27
IEC 61000-4-28 NOTE Harmonized as EN 61000-4-28
IEC 61000-4-31 NOTE Harmonized as EN 61000-4-31
IEC 61000-4-34 NOTE Harmonized as EN 61000-4-34
IEC 61000-4-39 NOTE Harmonized as EN 61000-4-39
IEC 61000-6-4 NOTE Harmonized as EN IEC 61000-6-4
IEC 61439 (series) NOTE Harmonized as EN IEC 61439 (series)
IEC 61508 (series) NOTE Harmonized as EN 61508 (series)
2
---------------------- Page: 4 ----------------------
SIST-TP CLC IEC/TR 63216:2020
CLC/IEC TR 63216:2020 (E)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60050-161 1990 International Electrotechnical Vocabulary. - -
Chapter 161: Electromagnetic compatibility
+ A1 1997 - -
+ A2 1998 - -
+ A3 2014 - -
+ A4 2014 - -
+ A5 2015 - -
+ A6 1990 - -
+ A7 2017 - -
+ A8 2018 - -
IEC 60050-441 - International Electrotechnical Vocabulary. - -
Switchgear, controlgear and fuses
IEC 60364-4-44 - Electrical installations of buildings -- Part 4- - -
44: Protection for safety - Protection
against voltage disturbances and
electromagnetic disturbances
IEC 60364-5-53 - Low-voltage electrical installations -- Part - -
5-53: Selection and erection of electrical
equipment - Protection, isolation,
switching, control and monitoring
IEC 60364-5-54 - Low-voltage electrical installations - Part 5- HD 60364-5-54 -
54: Selection and erection of electrical
equipment - Earthing arrangements and
protective conductors
IEC 60947-1 - Low-voltage switchgear and controlgear - EN 60947-1 -
Part 1: General rules
IEC 61000-2-4 2002 Electromagnetic compatibility (EMC) - Part EN 61000-2-4 2002
2-4: Environment - Compatibility levels in
industrial plants for low-frequency
conducted disturbances
3
---------------------- Page: 5 ----------------------
SIST-TP CLC IEC/TR 63216:2020
CLC/IEC TR 63216:2020 (E)
Publication Year Title EN/HD Year
IEC 61000-4-2 2008 Electromagnetic compatibility (EMC) - Part EN 61000-4-2 2009
4-2: Testing and measurement techniques
- Electrostatic discharge immunity test
IEC 61000-4-3 - Electromagnetic compatibility (EMC) - Part EN 61000-4-3 -
4-3: Testing and measurement techniques
- Radiated, radio-frequency,
electromagnetic field immunity test
IEC 61000-4-4 - Electromagnetic compatibility (EMC) - Part EN 61000-4-4 -
4-4: Testing and measurement techniques
- Electrical fast transient/burst immunity
test
IEC 61000-4-5 - Electromagnetic compatibility (EMC) - Part EN 61000-4-5 -
4-5: Testing and measurement techniques
- Surge immunity test
IEC 61000-4-6 - Electromagnetic compatibility (EMC) - Part EN 61000-4-6 -
4-6: Testing and measurement techniques
- Immunity to conducted disturbances,
induced by radio-frequency fields
IEC 61000-4-8 - Electromagnetic compatibility (EMC) - Part EN 61000-4-8 -
4-8: Testing and measurement techniques
- Power frequency magnetic field immunity
test
IEC 61000-4-11 - Electromagnetic compatibility (EMC) - Part EN IEC 61000-4--
4-11: Testing and measurement 11
techniques - Voltage dips, short
interruptions and voltage variations
immunity tests for equipment with input
current up to 16 A per phase
IEC 61000-4-13 - Electromagnetic compatibility (EMC) - Part EN 61000-4-13 -
4-13: Testing and measurement
techniques - Harmonics and
interharmonics including mains signalling
at a.c. power port, low frequency immunity
tests
IEC 61000-4-16 - Electromagnetic compatibility (EMC) - Part EN 61000-4-16 -
4-16: Testing and measurement
techniques - Test for immunity to
conducted, common mode disturbances in
the frequency range 0 Hz to 150 kHz
IEC 61000-4-18 - Electromagnetic compatibility (EMC) - Part EN IEC 61000-4--
4-18: Testing and measurement 18
techniques - Damped oscillatory wave
immunity test
IEC 61000-4-19 - Electromagnetic compatibility (EMC) - Part EN 61000-4-19 -
4-19: Testing and measurement
techniques - Test for immunity to
conducted, differential mode disturbances
and signalling in the frequency range 2 kHz
to 150 kHz at a.c. power ports
IEC 61000-6-1 - Electromagnetic compatibility (EMC) - Part EN IEC 61000-6-1 -
6-1: Generic standards - Immunity
standard for residential, commercial and
light-industrial environments
4
---------------------- Page: 6 ----------------------
SIST-TP CLC IEC/TR 63216:2020
CLC/IEC TR 63216:2020 (E)
Publication Year Title EN/HD Year
IEC 61000-6-2 - Electromagnetic compatibility (EMC) - Part EN IEC 61000-6-2 -
6-2: Generic standards - Immunity
standard for industrial environments
IEC 61000-6-3 - Electromagnetic compatibility (EMC) - Part EN 61000-6-3 -
6-3: Generic standards - Emission
standard for residential, commercial and
light-industrial environments
IEC 61000-6-5 - Electromagnetic compatibility (EMC) - Part EN 61000-6-5 -
6-5: Generic standards - Immunity for
equipment used in power station and
substation environment
IEC 61000-6-7 - Electromagnetic compatibility (EMC) - Part EN 61000-6-7 -
6-7: Generic standards - Immunity
requirements for equipment intended to
perform functions in a safety-related
system (functional safety) in industrial
locations
Industrial-process measurement and
IEC 61131-2 - EN 61131-2 -
control – Programmable controllers – Part
2: Equipment requirements and tests
IEC 61439-1 2011 Low-voltage switchgear and controlgear EN 61439-1 2011
assemblies - Part 1: General rules
IEC 61800-3 - Adjustable speed electrical power drive EN IEC 61800-3 -
systems - Part 3: EMC requirements and
specific test methods
IEC Guide 107 - Electromagnetic compatibility - Guide to - -
the drafting of electromagnetic
compatibility publications
CISPR 11 (mod) 2015 Industrial, scientific and medical equipment EN 55011 2016
- Radio-frequency disturbance
characteristics - Limits and methods of
measurement
+ A1 2016 + A1 2017
+ A2 2019 - -
- - + A11 2020
CISPR 32 - Electromagnetic compatibility of multimedia EN 55032 -
equipment - Emission requirements
Voltage characteristics of electricity EN 50160 -
supplied by public electricity networks
5
---------------------- Page: 7 ----------------------
SIST-TP CLC IEC/TR 63216:2020
---------------------- Page: 8 ----------------------
SIST-TP CLC IEC/TR 63216:2020
IEC TR 63216
®
Edition 1.0 2019-10
TECHNICAL
REPORT
colour
inside
Low-voltage switchgear and controlgear – Electromagnetic compatibility
assessment for switchgear and controlgear and their assemblies
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 29.130.20 ISBN 978-2-8322-7542-9
Warning! Make sure that you obtained this publication from an authorized distributor.
® Registered trademark of the International Electrotechnical Commission
---------------------- Page: 9 ----------------------
SIST-TP CLC IEC/TR 63216:2020
– 2 – IEC TR 63216:2019 © IEC 2019
CONTENTS
FOREWORD . 4
INTRODUCTION . 6
1 Scope . 7
2 Normative references . 7
3 Terms and definitions . 9
4 Classification of the electromagnetic environments . 11
4.1 General . 11
4.2 Emission classification . 11
4.3 Environments . 12
4.4 Low voltage supply . 14
4.4.1 Nominal voltages . 14
4.4.2 Faults in power supply networks . 14
4.4.3 Nominal frequencies . 14
4.4.4 Electromagnetic disturbances in power supply networks . 15
4.5 EMC environment classification . 15
4.6 Principle of compatibility . 16
5 Drafting of EMC requirements . 16
5.1 General . 16
5.2 EMC assessment . 17
5.3 Drafting of EMC requirements in product and assembly standards . 17
6 Radiocommunication . 18
6.1 General . 18
6.2 Radiated emissions . 18
6.3 Conducted emissions . 18
6.4 Immunity . 18
6.4.1 General . 18
6.4.2 Radiated immunity . 19
6.4.3 Radio frequency (common mode) . 19
6.5 Typical radiocommunication standards . 19
7 EMC related information . 19
7.1 Information on the product environment . 19
7.2 Information related to emission limits . 19
7.3 Instruction for use . 20
7.4 Good wiring practices . 20
8 Test levels of switchgear and controlgear . 20
8.1 Emission limits and test methods . 20
8.2 Immunity test levels . 21
8.3 Type tests . 23
Annex A (informative) Rationale of the electromagnetic compatibility based on the
electric network topology . 24
A.1 General . 24
A.2 Overvoltage levels in the installation . 24
Annex B (informative) Electromagnetic phenomena . 25
B.1 EMC phenomena . 25
B.1.1 General . 25
B.1.2 Voltage dips and short interruptions . 25
---------------------- Page: 10 ----------------------
SIST-TP CLC IEC/TR 63216:2020
IEC TR 63216:2019 © IEC 2019 – 3 –
B.1.3 Overvoltages . 25
B.1.4 Sine wave disturbances . 26
B.1.5 Three-phase system disturbances . 26
B.1.6 Electromagnetic disturbances . 26
B.1.7 Electromagnetic fields (EMF) . 27
B.1.8 Transient . 27
B.1.9 Radiated modulated disturbances . 27
B.1.10 Radio frequency identification (RFID) systems . 27
B.1.11 Radiated pulsed disturbances . 28
B.1.12 Electrostatic discharge . 28
B.2 Relation between testing standards and basic phenomena . 28
Bibliography . 31
Figure 1 – Ports of entry of electromagnetic disturbances into equipment . 11
Figure 2 – Example of EMC environments . 13
Figure 3 – Principle of EMC compatibility . 16
Figure 4 – CISPR 11:2015, Class A limits (quasi peak) for conducted and radiated
emission at 10 m . 21
Table 1 – Typical environment levels . 15
Table 2 – Minimum immunity test levels . 21
Table A.1 – Relation between surge coupling and overvoltage category . 24
Table B.1 – Testing standards covering basic phenomena . 29
---------------------- Page: 11 ----------------------
SIST-TP CLC IEC/TR 63216:2020
– 4 – IEC TR 63216:2019 © IEC 2019
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR –
Electromagnetic compatibility assessment
for switchgear and controlgear and their assemblies
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
The main task of IEC technical committees is to prepare International Standards. However, a
technical committee may propose the publication of a technical report when it has collected
data of a different kind from that which is normally published as an International Standard, for
example "state of the art".
IEC TR 63216, which is a technical report, has been prepared by subcommittee 121A: Low-
voltage switchgear and controlgear, of IEC technical committee 121: Switchgear and
controlgear and their assemblies for low voltage.
The text of this technical report is based on the following documents:
Enquiry draft Report on voting
121A/292/DTR 121A/306A/RVDTR
Full information on the voting for the approval of this technical report can be found in the
report on voting indicated in the above table.
---------------------- Page: 12 ----------------------
SIST-TP CLC IEC/TR 63216:2020
IEC TR 63216:2019 © IEC 2019 – 5 –
This document has been drafted in accordance with the ISO/IEC Directives, Part 2.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under "http://webstore.iec.ch" in the data related to
the specific document. At this date, the document will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
A bilingual version of this publication may be issued at a later date.
IMPORTANT – The 'colour inside' logo on the cover page of this publication indicates
that it contains colours which are considered to be useful for the correct
understanding of its contents. Users should therefore print this document using a
colour printer.
---------------------- Page: 13 ----------------------
SIST-TP CLC IEC/TR 63216:2020
– 6 – IEC TR 63216:2019 © IEC 2019
INTRODUCTION
Low-voltage switchgear and controlgear and their assemblies (hereinafter referred to as
"equipment") compliant with their standards, when installed and used in accordance with
manufacturer's instructions, operate safely and reliably with a good level of immunity and do
not produce interferences in normal operation or reasonably foreseeable faulty conditions.
This document is intended to support discussions within IEC TC 121 and its sub-committees,
and with other TCs/SCs, by explaining electromagnetic compatibility assessment of
equipment and compatibility measures contained in the IEC 60947 series of standards.
Those measures are based on a system approach, depending on the EMC environment in
industrial applications. They include design rules and type tests to ensure the compatibility of
equipment to the intended electromagnetic environment.
The collection of IEC 61000 series is very large and very generic. The intent of this document
is to provide the essential applicable EMC concepts for IEC TC 121 and its sub-committees'
working groups, maintenance teams and project teams.
For this intent, this document defines specific descriptions of the relevant EMC environments
which are derived from the generic ones of IEC 61000 series. In addition, these environments
are consistent with the zones defined by IEC 61131-2.
---------------------- Page: 14 ----------------------
SIST-TP CLC IEC/TR 63216:2020
IEC TR 63216:2019 © IEC 2019 – 7 –
LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR –
Electromagnetic compatibility assessment
for switchgear and controlgear and their assemblies
1 Scope
The purpose of this document is to define homogeneous categories for the electromagnetic
environments in order to harmonize as far as practicable all general rules and product
standard requirements of electromagnetic compatibility (EMC), applicable to low-voltage
switchgear, controlgear and their assemblies with built-in electronic circuits.
This document also addresses incorporated radiocommunication functions.
The typical application environments for such equipment include the electrical distribution in
infrastructure, commercial and industrial buildings and the control systems of machinery,
including motor-driven systems.
The primary intention of EMC requirements is to ensure the safe and reliable operation of the
equipment, as well as the communication efficiency of the radiocommunication equipment
within their intended environments.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their
content constitutes requirements of this document. For dated references, only the edition
cited applies. For undated references, the latest edition of the referenced document (including
any amendments) applies.
IEC 60050-161:1990, International Electrotechnical Vocabulary (IEV) – Part 161:
Electromagnetic compatibility
IEC 60050-161:1990/AMD1:1997
IEC 60050-161:1990/AMD2:1998
IEC 60050-161:1990/AMD3:2014
IEC 60050-161:1990/AMD4:2014
IEC 60050-161:1990/AMD5:2015
IEC 60050-161:1990/AMD6:2016
IEC 60050-161:1990/AMD7:2017
IEC 60050-161:1990/AMD8:2018
IEC 60050-441, International Electrotechnical Vocabulary (IEV) – Part 441: Switchgear,
controlgear and fuses
IEC 60364-4-44, Low-voltage electrical installations – Part 4-44: Protection for safety –
Protection against voltage disturbances and electromagnetic disturbances
IEC 60364-5-53, Low-voltage electrical installations – Part 5-53: Selection and erection of
electrical equipment – Devices for protection for safety, isolation, switching, control and
monitoring
IEC 60364-5-54, Low-voltage electrical installations – Part 5-54: Selection and erection of
electrical equipment – Earthing arrangements and protective conductors
---------------------- Page: 15 ----------------------
SIST-TP CLC IEC/TR 63216:2020
– 8 – IEC TR 63216:2019 © IEC 2019
IEC 60947-1, Low-voltage switchgear and controlgear – Part 1: General rules
IEC 61000-2-4:2002, Electromagnetic compatibility (EMC) – Part 2-4: Environment –
Compatibility levels in industrial plants for low-frequency conducted disturbances
IEC 61000-4-2:2008, Electromagnetic compatibility (EMC) – Part 4-2: Testing and
measurement techniques – Electrostatic discharge immunity test
IEC 61000-4-3, Electromagnetic compatibility (EMC) – Part 4-3: Testing and measurement
techniques – Radiated, radio-frequency, electromagnetic field immunity test
IEC 61000-4-4, Electromagnetic compatibility (EMC)
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.