SIST EN ISO 15614-6:2006
(Main)Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 6: Arc and gas welding of copper and its alloys (ISO 15614-6:2006)
Specification and qualification of welding procedures for metallic materials - Welding procedure test - Part 6: Arc and gas welding of copper and its alloys (ISO 15614-6:2006)
ISO 15614-6:2006 specifies how a preliminary welding procedure specification is qualified by welding procedure tests. It applies to the arc and gas welding of copper and copper alloys in all product forms.
Anforderung und Qualifizierung von Schweißverfahren für metallische Werkstoffe - Schweißverfahrensprüfung - Teil 6: Lichtbogen- und Gasschweißen von Kupfer und seinen Legierungen (ISO 15614-6:2006)
Dieser Teil von ISO 15614 legt fest, wie eine Schweißanweisung durch Schweißverfahrensprüfungen qualifiziert wird. Er wird angewendet beim Lichtbogenschweißen und Gasschweißen von Kupfer- und Kupferlegierungen in allen Produktformen.
Dieser Teil von ISO 15614 definiert die Bedingungen für die Durchführung der Schweißverfahrensprüfungen und den Geltungsbereich für Schweißverfahren für alle praktischen schweißtechnischen Tätigkeiten innerhalb des Bereiches der Einflussgrößen nach Abschnitt 9.
Dieser Teil von ISO 15614 ist für alle neuen Schweißverfahren anwendbar. Er setzt jedoch bereits bestehende Schweißverfahrensprüfungen, die nach früheren nationalen Normen oder Regeln durchgeführt wurden, nicht außer Kraft. Wenn zusätzliche Prüfungen verlangt werden, um die Qualifizierungen technisch anzupassen, sind nur diese zusätzlichen Prüfungen an einem Prüfstück durchzuführen, das mit den Bestimmungen dieses Teils von ISO 15614 übereinstimmen sollte.
Zusätzliche Prüfungen dürfen durch die Anwendungsnormen gefordert werden.
Die Grundsätze dieses Teils von ISO 15614 dürfen bei anderen Schmelzschweißprozessen angewendet werden.
Descriptif et qualification d'un mode opératoire de soudage pour les matériaux métalliques - Épreuve de qualification d'un mode opératoire de soudage - Partie 6: Soudage a l'arc et aux gaz du cuivre et de ses alliages (ISO 15614-6:2006)
L'ISO 15614-6:2006 spécifie comment un descriptif de mode opératoire de soudage préliminaire est qualifié par une épreuve. Elle est applicable au soudage à l'arc et aux gaz du cuivre et des alliages de cuivre sous toutes ses formes.
Popis in kvalifikacija varilnih postopkov za kovinske materiale - Preskus varilnega postopka - 6. del: Obločno in plamensko varjenje bakra in njegovih zlitin (ISO 15614-6:2006)
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-oktober-2006
3RSLVLQNYDOLILNDFLMDYDULOQLKSRVWRSNRY]DNRYLQVNHPDWHULDOH±3UHVNXVYDULOQHJD
SRVWRSND±GHO 2EORþQRYDUMHQMHEDNUDLQQMHJRYLK]OLWLQ ,62
Specification and qualification of welding procedures for metallic materials - Welding
procedure test - Part 6: Arc and gas welding of copper and its alloys (ISO 15614-6:2006)
Anforderung und Qualifizierung von Schweißverfahren für metallische Werkstoffe -
Schweißverfahrensprüfung - Teil 6: Lichtbogen- und Gasschweißen von Kupfer und
seinen Legierungen (ISO 15614-6:2006)
Descriptif et qualification d'un mode opératoire de soudage pour les matériaux
métalliques - Épreuve de qualification d'un mode opératoire de soudage - Partie 6:
Soudage a l'arc et aux gaz du cuivre et de ses alliages (ISO 15614-6:2006)
Ta slovenski standard je istoveten z: EN ISO 15614-6:2006
ICS:
25.160.10 Varilni postopki in varjenje Welding processes
77.120.30 Baker in bakrove zlitine Copper and copper alloys
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 15614-6
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2006
ICS 25.160.10
English Version
Specification and qualification of welding procedures for metallic
materials - Welding procedure test - Part 6: Arc and gas welding
of copper and its alloys (ISO 15614-6:2006)
Descriptif et qualification d'un mode opératoire de soudage Anforderung und Qualifizierung von Schweißverfahren für
pour les matériaux métalliques - Épreuve de qualification metallische Werkstoffe - Schweißverfahrensprüfung - Teil
d'un mode opératoire de soudage - Partie 6: Soudage à 6: Lichtbogenschweißen von Kupfer seinen Legierungen
l'arc et aux gaz du cuivre et de ses alliages (ISO 15614- (ISO 15614-6:2006)
6:2006)
This European Standard was approved by CEN on 16 March 2006.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15614-6:2006: E
worldwide for CEN national Members.
Foreword
This document (EN ISO 15614-6:2006) has been prepared by Technical Committee CEN/TC 121
"Welding", the secretariat of which is held by DIN, in collaboration with Technical Committee
ISO/TC 44 "Welding and allied processes".
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by October 2006, and conflicting national standards
shall be withdrawn at the latest by October 2006.
This document has been prepared under a mandate given to CEN by the European Commission
and the European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this
document.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Cyprus,
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
ANNEX ZA
(informative)
Relationship between this International Standard and the Essential
Requirements of EU Directive 97/05/IEC
This European Standard has been prepared under a mandate given to CEN by the European
Commission to provide a means of conforming to Essential Requirements of the New Approach
Directives 97/23/EC.
Once this standard is cited in the Official Journal of the European Communities under that Directive
and has been implemented as a national standard in at least one Member State, compliance with
the clauses of this standard given in Table ZA confers, within the limits of the scope of this
standard, a presumption of conformity with the corresponding Essential Requirements of that
Directive and associated EFTA regulations.
Table ZA — Correspondence between this European Standard and Directive 97/23/EC
Clause(s)/Sub-clause(s) of Essential Requirements (ERs) of Qualifying remarks/Notes
this EN Directive 97/23/EC
Clauses 4, 5, 6, 7, 8, 9, 10 Annex l, 3.1.2 Permanent joining
WARNING: Other requirements and other EU Directives may be applicable to the product(s) falling
within the scope of this standard.
INTERNATIONAL ISO
STANDARD 15614-6
First edition
2006-04-01
Specification and qualification of welding
procedures for metallic materials —
Welding procedure test —
Part 6:
Arc and gas welding of copper and its
alloys
Descriptif et qualification d'un mode opératoire de soudage pour les
matériaux métalliques — Épreuve de qualification d'un mode opératoire
de soudage —
Partie 6: Soudage à l'arc et aux gaz du cuivre et de ses alliages
Reference number
ISO 15614-6:2006(E)
©
ISO 2006
ISO 15614-6:2006(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2006
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2006 – All rights reserved
ISO 15614-6:2006(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions. 2
4 Welding processes . 2
5 Preliminary welding procedure specification (pWPS) . 2
6 Welding procedure test. 3
7 Test piece . 3
7.1 General. 3
7.2 Shape and dimensions of test pieces. 3
7.3 Welding of test pieces. 4
8 Examination and testing . 7
8.1 Extent of testing. 7
8.2 Location and taking of test specimens . 8
8.3 Non-destructive testing. 8
8.4 Destructive testing. 12
8.5 Acceptance levels. 13
8.6 Re-testing . 13
9 Range of qualification . 14
9.1 General. 14
9.2 Related to the manufacturer . 14
9.3 Related to the parent material . 14
9.4 Common to all welding procedures. 16
9.5 Specific to processes. 18
10 Welding procedure qualification record (WPQR) . 18
Annex A (informative) Welding Procedure Qualification Record form (WPQR) . 19
Bibliography . 22
ISO 15614-6:2006(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 15614-6 was prepared by the European Committee for Standardization (CEN) Technical Committee
CEN/TC 121, Welding, in collaboration with Technical Committee ISO/TC 44, Welding and allied processes,
Subcommittee SC 10, Unification of requirements in the field of metal welding, in accordance with the
Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
ISO 15614 consists of the following parts, under the general title Specification and qualification of welding
procedures for metallic materials — Welding procedure test:
⎯ Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys
⎯ Part 2: Arc welding of aluminium and its alloys
⎯ Part 3: Fusion and pressure welding of non-alloyed and low-alloyed cast irons
⎯ Part 4: Finishing welding of aluminium castings
⎯ Part 5: Arc welding of titanium, zirconium and their alloys
⎯ Part 6: Arc and gas welding of copper and its alloys
⎯ Part 7: Overlay welding
⎯
...
SLOVENSKI STANDARD
01-oktober-2006
Popis in kvalifikacija varilnih postopkov za kovinske materiale - Preskus varilnega
postopka - 6. del: Obločno in plamensko varjenje bakra in njegovih zlitin (ISO
15614-6:2006)
Specification and qualification of welding procedures for metallic materials - Welding
procedure test - Part 6: Arc and gas welding of copper and its alloys (ISO 15614-6:2006)
Anforderung und Qualifizierung von Schweißverfahren für metallische Werkstoffe -
Schweißverfahrensprüfung - Teil 6: Lichtbogen- und Gasschweißen von Kupfer und
seinen Legierungen (ISO 15614-6:2006)
Descriptif et qualification d'un mode opératoire de soudage pour les matériaux
métalliques - Épreuve de qualification d'un mode opératoire de soudage - Partie 6:
Soudage a l'arc et aux gaz du cuivre et de ses alliages (ISO 15614-6:2006)
Ta slovenski standard je istoveten z: EN ISO 15614-6:2006
ICS:
25.160.10 Varilni postopki in varjenje Welding processes
77.120.30 Baker in bakrove zlitine Copper and copper alloys
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN ISO 15614-6
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2006
ICS 25.160.10
English Version
Specification and qualification of welding procedures for metallic
materials - Welding procedure test - Part 6: Arc and gas welding
of copper and its alloys (ISO 15614-6:2006)
Descriptif et qualification d'un mode opératoire de soudage Anforderung und Qualifizierung von Schweißverfahren für
pour les matériaux métalliques - Épreuve de qualification metallische Werkstoffe - Schweißverfahrensprüfung - Teil
d'un mode opératoire de soudage - Partie 6: Soudage à 6: Lichtbogenschweißen von Kupfer seinen Legierungen
l'arc et aux gaz du cuivre et de ses alliages (ISO 15614- (ISO 15614-6:2006)
6:2006)
This European Standard was approved by CEN on 16 March 2006.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2006 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15614-6:2006: E
worldwide for CEN national Members.
Foreword
This document (EN ISO 15614-6:2006) has been prepared by Technical Committee CEN/TC 121
"Welding", the secretariat of which is held by DIN, in collaboration with Technical Committee
ISO/TC 44 "Welding and allied processes".
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by October 2006, and conflicting national standards
shall be withdrawn at the latest by October 2006.
This document has been prepared under a mandate given to CEN by the European Commission
and the European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this
document.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Cyprus,
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland,
Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
ANNEX ZA
(informative)
Relationship between this International Standard and the Essential
Requirements of EU Directive 97/05/IEC
This European Standard has been prepared under a mandate given to CEN by the European
Commission to provide a means of conforming to Essential Requirements of the New Approach
Directives 97/23/EC.
Once this standard is cited in the Official Journal of the European Communities under that Directive
and has been implemented as a national standard in at least one Member State, compliance with
the clauses of this standard given in Table ZA confers, within the limits of the scope of this
standard, a presumption of conformity with the corresponding Essential Requirements of that
Directive and associated EFTA regulations.
Table ZA — Correspondence between this European Standard and Directive 97/23/EC
Clause(s)/Sub-clause(s) of Essential Requirements (ERs) of Qualifying remarks/Notes
this EN Directive 97/23/EC
Clauses 4, 5, 6, 7, 8, 9, 10 Annex l, 3.1.2 Permanent joining
WARNING: Other requirements and other EU Directives may be applicable to the product(s) falling
within the scope of this standard.
INTERNATIONAL ISO
STANDARD 15614-6
First edition
2006-04-01
Specification and qualification of welding
procedures for metallic materials —
Welding procedure test —
Part 6:
Arc and gas welding of copper and its
alloys
Descriptif et qualification d'un mode opératoire de soudage pour les
matériaux métalliques — Épreuve de qualification d'un mode opératoire
de soudage —
Partie 6: Soudage à l'arc et aux gaz du cuivre et de ses alliages
Reference number
ISO 15614-6:2006(E)
©
ISO 2006
ISO 15614-6:2006(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2006
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii © ISO 2006 – All rights reserved
ISO 15614-6:2006(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions. 2
4 Welding processes . 2
5 Preliminary welding procedure specification (pWPS) . 2
6 Welding procedure test. 3
7 Test piece . 3
7.1 General. 3
7.2 Shape and dimensions of test pieces. 3
7.3 Welding of test pieces. 4
8 Examination and testing . 7
8.1 Extent of testing. 7
8.2 Location and taking of test specimens . 8
8.3 Non-destructive testing. 8
8.4 Destructive testing. 12
8.5 Acceptance levels. 13
8.6 Re-testing . 13
9 Range of qualification . 14
9.1 General. 14
9.2 Related to the manufacturer . 14
9.3 Related to the parent material . 14
9.4 Common to all welding procedures. 16
9.5 Specific to processes. 18
10 Welding procedure qualification record (WPQR) . 18
Annex A (informative) Welding Procedure Qualification Record form (WPQR) . 19
Bibliography . 22
ISO 15614-6:2006(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 15614-6 was prepared by the European Committee for Standardization (CEN) Technical Committee
CEN/TC 121, Welding, in collaboration with Technical Committee ISO/TC 44, Welding and allied processes,
Subcommittee SC 10, Unification of requirements in the field of metal welding, in accordance with the
Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
ISO 15614 consists of the following parts, under the general title Specification and qualification of welding
procedures for metallic materials — Welding procedure test:
⎯ Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys
⎯ Part 2: Arc welding of aluminium and its alloys
⎯ Part 3: Fusion and pressure welding of non-alloyed and low-alloyed cast irons
⎯ Part 4: Finishing welding of aluminium castings
⎯ Part 5: Arc welding of titanium, zirconium and their alloys
⎯ Part 6: Arc and gas welding of copper and its alloys
⎯ Part 7: Overlay welding
⎯ Pa
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.