SIST EN 14144:2004
(Main)Lifebuoys - Requirements, tests
Lifebuoys - Requirements, tests
This standard applies to lifebuoys used on watercraft in sea and inland navigation, on floating bodies, floating equipment, marine equipment and shore equipment in the vicinity of bodies of water.
The standard specifies the main dimensions, design, safety requirements and testing of lifebuoys.
Rettungsringe - Anforderungen, Prüfungen
Diese Norm gilt für Rettungsringe, die auf Wasserfahrzeugen in der See- und Binnenschifffahrt, auf Schwimmkörpern, schwimmenden Anlagen, meerestechnischen Anlagen sowie für Landanlagen im Bereich von Wasserflächen verwendet werden.
Die Norm dient dazu, Hauptmaße, Konstruktion, Sicherheitsanforderungen und Prüfungen von Rettungsringen festzulegen.
Bouées de sauvetage - Exigences, essais
Rešilni pasovi – Zahteve, preskusi
General Information
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Rešilni pasovi – Zahteve, preskusiRettungsringe - Anforderungen, PrüfungenBouées de sauvetage - Exigences, essaisLifebuoys - Requirements, tests47.080ýROQLSmall craft13.340.60Protection against falling and slippingICS:Ta slovenski standard je istoveten z:EN 14144:2003SIST EN 14144:2004en01-september-2004SIST EN 14144:2004SLOVENSKI
STANDARD
SIST EN 14144:2004
EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 14144April 2003ICS 47.080English versionLifebuoys - Requirements, testsBouées de sauvetage - Exigences, essaisRettungsringe - Anforderungen, PrüfungenThis European Standard was approved by CEN on 2 January 2003.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the Management Centre has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece,Iceland, Ireland, Italy, Luxembourg, Malta, Netherlands, Norway, Portugal, Slovakia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre: rue de Stassart, 36
B-1050 Brussels© 2003 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 14144:2003 ESIST EN 14144:2004
EN 14144:2003 (E) 2 Contents Page Foreword.3 1 Scope.4 2 Normative references.4 3 Terms and definitions.4 4 Safety requirements.5 4.1 Design.5 4.1.1 General.5 4.1.2 Buoyancy body.5 4.1.3 Top material.5 4.1.4 Grab line.5 4.1.5 Reflective strips.5 4.1.6 Colour.5 4.2 Dimensions.6 4.3 Buoyancy.6 4.4 Mass.6 4.5 Strength.6 4.6 Resistance.7 4.7 Burning behaviour.7 4.8 Temperature ranges for serviceability.7 5 Testing.7 5.1 General.7 5.1.1 Scope and sequence of testing.7 5.1.2 Manufacturer's certificates.7 5.1.3 Testing body.8 5.2 Dimensions, mass, design.8 5.3 Temperature tests.8 5.4 Drop test.8 5.4.1 Free fall into water.8 5.4.2 Free fall onto concrete floor.8 5.5 Resistance.8 5.5.1 Resistance to diesel fuel.8 5.5.2 Resistance to seawater.8 5.6 Strength.9 5.7 Load-carrying capacity.9 6 Designation.9 7 Marking.9 Bibliography.10
SIST EN 14144:2004
EN 14144:2003 (E) 3 Foreword This document EN 14144:2003 has been prepared by Technical Committee CEN/TC 15 “Inland navigation vessels”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2003, and conflicting national standards shall be withdrawn at the latest by October 2003 The standard specifies requirements for lifebuoys within the meaning of the following Directives: - 96/98/EC of 20 December 1996 on marine equipment and - 82/714/EEC: Council Directive of 4 October 1982 laying down technical requirements for inland waterway vessels. The standard is intended to apply generally, i.e. not just to inland navigation vessels, but also to seagoing vessels. This document contains bibliographical references. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are b
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.